* libertas: does not depend on mac80211 but on cfg80211 and it uses wext
* libipw: also uses wext
* net-hermes: it is enough if the main package net-hermes depends on cfg80211
* Now it is possible to build it without cfg80211 at all
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28437 3c298f89-4303-0410-b956-a3cf2f4a3e73
The old firmware for ath9k_htc was not compatible with the driver since april.
Also update to a new version of linux-firmware to get the newest version of these firmware files.
Thank you Helmut Schaa for reporting this.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28433 3c298f89-4303-0410-b956-a3cf2f4a3e73
wireless-testing 2011-08-26 properly detects and works with linux 3.1.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28096 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is always used to build a firmware for linux systems also if we are on freebsd.
This is one patch from #9897
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27926 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes b43 work on broadcom SoCs using bcma as system bus.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27734 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the firmware from linux-firmware git where possible.
Update some firmware files in that process and check for missing firmware files for some modules.
* update Ralink firmwares
* update ath9k_htc firmware
* add firmware for mwl8k
* add more firmware files for libertas-sd and libertas-usb
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27252 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow enabling of N-PHY support for BCM4321 and BCM4322.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26736 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow reenabling the PIO mode fallback for b43.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26735 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow enabling debug output and debugfs for B43.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26734 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the 5.10.56.27 firmware option. This includes updating b43-fwcutter to
its newest release 14 and updating the b43-fwsquash.py to recognise rev 16
n phy files.
Also rename the current options from STABLE/EXPERIMENTAL to their version
numbers.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26733 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently the device id in the platform driver is hardcoded to an
id which is specific to AR9130/AR9132 SOCs as it supports only wmac
(wireless mac) of these SOCs. But this needs to be dynamic when we
want to support different wmac of SOCs. So add id_table to driver to
make it extendable to more SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26604 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Some module should be loaded later to load them after the modules they are depending on
* add some more missing config symbols
* make CS5535 build again
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26570 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds the Intel wireless drivers for their normal cards.
Thank you framer99 for the patch, I extended it a little bit.
This closes#7227
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26534 3c298f89-4303-0410-b956-a3cf2f4a3e73
adds some more pending patches which (among other things) fix the 'failed to stop RX DMA' messages
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26506 3c298f89-4303-0410-b956-a3cf2f4a3e73
Felix Fietkau
Nicolas Thill
Jonas Gorski
Jo-Philipp Wich
Hauke Mehrtens
Hamish Guthrie
Gabor Juhos