Armada XP/370 boards share these hardware blocks with Orion and Kirkwood
SoCs.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35059 3c298f89-4303-0410-b956-a3cf2f4a3e73
These symbols are used by 3.8+ kernels
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35054 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thanks to kyak for spotting this
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35047 3c298f89-4303-0410-b956-a3cf2f4a3e73
Summary:
* remove all files/* (since merged to upstream)
* patches on nand-spl, mmc and lcd driver
Thanks a lot to Xiangfu Liu!
Signed-off-by: Xiangfu Liu <xiangfu@sharism.cc>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35034 3c298f89-4303-0410-b956-a3cf2f4a3e73
The busybox size is increased by 3.2KByte uncompressed on bcm47xx with
this commit.
This zram-swap automatically creates a zram device, a swap partition on
it and make the kernel swap pages to it.
Thank you Bastian Bittorf <bittorf@bluebottle.com> for idea and the
script.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35025 3c298f89-4303-0410-b956-a3cf2f4a3e73
I wanted to use some statistics from /sys/kernel/debug/ieee80211,
so I enabled PACKAGE_MAC80211_DEBUGFS. But I could not use it,
because CONFIG_KERNEL_DEBUG_FS was not set and it's a little bit
hidden. After manually setting CONFIG_KERNEL_DEBUG_FS to y,
everything was fine. This patch automatically selects
CONFIG_KERNEL_DEBUG_FS if PACKAGE_MAC80211_DEBUGFS is set.
Additionally, the help text says "Say N unless you know you need this.",
but it's default y. This help text is copied verbatim from the
kernel's Kconfig and not true for us. So remove this part of the
help text
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35014 3c298f89-4303-0410-b956-a3cf2f4a3e73
This prevents private traffic from leaking out to the internet
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35012 3c298f89-4303-0410-b956-a3cf2f4a3e73
remove firmware for LP-Phy core rev 14, I have never seen such a device.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35000 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds diag leds/buttons support for Linksys E1000 V1. It worked on
my router, however it may need some tweaking by people more familiar
with openwrt and c to make it fit for commiting.
Thank you hhm for this patch.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34996 3c298f89-4303-0410-b956-a3cf2f4a3e73
I wrote this patch some time ago because I had a need for one of the
Gigabit ports (Linksys E3000) to be forced to 100FD. This is based
on the robocfg sources included w/ the RT-N16 sources from ASUS.
Since work is progressing on a BGMAC driver that could be included in
OpenWRT, this may be useful to someone else.
In testing, forcing the speed to 10/100 or 1000 worked fine; however,
when trying to force full-duplex mode, the result was always
half-duplex. I was not able to isolate the source of the problem
(this patch, driver or H/W limitation). The only way I could get it
to work was to set the port to Auto, but then only advertise 100FD
(not included in this patch).
I have a modified version of the robocfg package as well, I'd have to
clean it up a little first (remove the full-duplex hack) before
submitting it if there is interest.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34992 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is in part based on a patch send by Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34991 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is the version like it was send for mainline inclusion.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34988 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Add support for blocking forwarding while address assignments
* Fix relay restarting function
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34985 3c298f89-4303-0410-b956-a3cf2f4a3e73
Neither --create-backup nor --restore-backup need an image name (following
the backup filename). Treat them in uniform way.
Mostly fixes#12346.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34974 3c298f89-4303-0410-b956-a3cf2f4a3e73
- introduce "list interface" options to specify the ifaces to listen on, takes uci- or network device name
- set the default system description to distrib @ hostname, e.g. "OpenWrt Barrier Breaker r34744 @ vbox"
- introduce "option lldp_description" to override the automatically generated description
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34970 3c298f89-4303-0410-b956-a3cf2f4a3e73
Felix Fietkau
Vasilis Tsiligiannis
Florian Fainelli
Mirko Vogt
Jo-Philipp Wich
Hauke Mehrtens
John Crispin
Steven Barth