72aba7b527
[brcm63xx] add 96348w3 board ( #10764 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32088 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06 15:45:04 +00:00
2e63f6da68
[brcm63xx] update livebox board support ( #8677 )
...
Merge most fixes from #8677 :
- add basic hardware detection of Livebox Blue 5g revisions
- register leds and gpio buttons
- fix boot address location
- properly parse mac addresses
Plus some more fixes:
- make board_livebox.c more in line with board_bcm963xx.c
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32087 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06 15:44:56 +00:00
0abe5c6244
[brcm63xx] fix leds naming for all bcm63xx boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32086 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06 15:44:52 +00:00
cc14bc096e
[brcm63xx] backport upstream spi-bcm63xx fixes
...
* message pump conversion
* not using stopping state
* setting spi driver mode bits
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32078 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06 13:31:33 +00:00
0c59a91df5
[brcm63xx] increase led number in patch 301-led_count.patch
...
So that board patches are only touching board-related code
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32076 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-06 13:31:24 +00:00
9f6ef16bdc
[brcm63xx] fix board patches so that new boards are withing appropriate ifdef
...
Some new board definitions were added within the #ifdef CONFIG_CPU_6338
section while some other were added within #ifdef CONFIG_CPU_6345, fix this
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32060 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-05 13:40:41 +00:00
c349282eff
[brcm63xx] fix bisectability of patch 303-spi-board-info.patch
...
It uses spi_register_board_info() from linux/spi/spi.h but does not include it
explicitely.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32058 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-05 13:40:35 +00:00
266c70cdf4
[kernel] bump to 3.3.8
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32055 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-05 06:57:51 +00:00
7d6df5d239
bcm63xx: fix ethernet on 96328avng and 963281TAN
...
The internal switch did not get registered.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32041 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-06-04 08:35:25 +00:00
b032357e85
bcm63xx: build images for 6328 reference boards with various flash sizes
...
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32004 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-30 10:27:46 +00:00
e343446e23
bcm63xx: readd accidentially dropped network config for SPW303V
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@32003 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-30 10:27:42 +00:00
b93700be90
bcm63xx: build images for DSL-274XB revision F1
...
Build images for D-Link DSL-274XB revision F1. Flashing
through original web UI as well as CFE works.
Known issues:
* wifi led inverted (on when wifi is off and vice cersa)
* same issues as generic bcm6328 support
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31885 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:51 +00:00
e4a82f8318
bcm63xx: add ath9k to atheros wifi profile
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31884 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:48 +00:00
2df17dbf20
bcm63xx: enable bcm6328 support and required drivers
...
BCM6328 support is in a usable state, with the following issues
* internal switch port not configurable
* external phys not supported
* broadcom wifis will probably not work correctly
* and all other generic bcm63xx issues (so yes, still no ADSL)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31883 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:46 +00:00
20cab203ed
bcm63xx: add support for DSL-274XB rev F1
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31882 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:43 +00:00
58de534f18
bcm63xx: fix port state after network down
...
bcm_enetsw_probe did not properly reset port states, resulting in
connected ports staying disabled after bringing up the interface the
second time.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31881 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:40 +00:00
9a873721da
bcm63xx: add a fixup for ath9k devices
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31880 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:37 +00:00
96ef7778af
bcm63xx: add support for the HSSPI controller
...
Add support for the HSSPI controller found on bcm6328 and SPI attached
flash.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31879 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:33 +00:00
5b950415b8
bcm63xx: add preliminary support for bcm6328
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31878 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:29 +00:00
bf8af3c6f2
bcm63xx: add flash type detection
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31877 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:25 +00:00
afb39de7d0
bcm63xx: pad Speedport W303 V images to 4 MiB
...
Prevents CFE from flashing to the second image offset. Fix up the rootfs
length on first boot else CFE will complain.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31876 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:22 +00:00
4ecf7d09a1
bcm63xx: add a default switch configuration for DSL-274XB
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31874 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:17 +00:00
4abdddf848
bcm63xx: setup network config through uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31873 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:14 +00:00
6082cee9d6
bcm63xx: move the board name workaround to /lib/brcm63xx.sh
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31872 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:11 +00:00
1148159a4f
bcm63xx: use the exact board id as board identification string
...
No need to keep the bcm63xx/ at the start or the chipid info at the end.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31871 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-27 13:22:08 +00:00
e100214e23
kernel: update linux 3.3 to 3.3.7
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31848 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-23 21:05:32 +00:00
cb4c118e50
linux: move certain disabled symbols to the generic configs
...
* CONFIG_ARCH_DMA_ADDR_T_64BIT
* CONFIG_ARCH_HAS_ILOG2_U32
* CONFIG_ARCH_HAS_ILOG2_U64
* CONFIG_ARCH_PHYS_ADDR_T_64BIT
* CONFIG_ARCH_SUPPORTS_MSI
* CONFIG_GENERIC_CPU_DEVICES
* CONFIG_HWMON_DEBUG_CHIP
* CONFIG_I2C_PXA_PCI
* CONFIG_LEDS_GPIO
* CONFIG_MINIX_FS_NATIVE_ENDIAN
* CONFIG_MLX4_CORE
* CONFIG_POWER_SUPPLY
* CONFIG_POWER_SUPPLY_DEBUG
* CONFIG_QUOTACTL
* CONFIG_SDIO_UART
* CONFIG_SENSORS_K10TEMP
* CONFIG_SENSORS_SCH56XX_COMMON
* CONFIG_SENSORS_VIA_CPUTEMP
* CONFIG_SERIO_AMBAKMI
* CONFIG_SERIO_I8042
* CONFIG_SERIO_LIBPS2
* CONFIG_SERIO_PCIPS2
* CONFIG_SERIO_RAW
* CONFIG_SERIO_SERPORT
* CONFIG_SPI_BITBANG
* CONFIG_SPI_GPIO
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31737 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-15 10:58:52 +00:00
cc87185921
kernel: update linux 3.3 to 3.3.6
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31709 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-14 09:18:32 +00:00
3303e79b79
kernel: update linux 3.3 to 3.3.5
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31645 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-07 20:11:43 +00:00
8336cde37f
bcm63xx: fix a race between PCI bus scan and fallback sprom registration
...
The fallback sprom handler was installed too late, resulting in ssb
failing to get a valid sprom on some devices.
Fixes #11384 .
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31638 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-06 21:25:34 +00:00
a9d023be01
[brcm63xx] use a define for the poll and debounce interval
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31550 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-05-02 15:40:26 +00:00
465b2a024c
kernel: update linux 3.3 to 3.3.4
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31541 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-30 08:38:11 +00:00
7466f87cc1
[brcm63xx] switch to gpio-keys-polled
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31491 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-27 16:44:48 +00:00
643a3ba58c
bcm63xx: drop linux 3.2 support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31464 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24 11:49:27 +00:00
f8cce554ff
bcm63xx: drop linux 3.0 support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31463 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24 11:49:24 +00:00
d4be3ed641
bcm63xx: switch kernel to 3.3
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31462 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-04-24 11:49:19 +00:00
4e77771341
bcm63xx: enable bcm6368 for linux 3.3 and build images
...
Only build bcm6368 images when building for linux 3.3.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31133 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28 20:42:37 +00:00
f60e4f7459
bcm63xx: add initial support for bcm6368 boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31132 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28 20:42:34 +00:00
d569a898ab
bcm63xx: add driver for the internal hw trng on bcm6368
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31131 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28 20:42:30 +00:00
37d45e311b
bcm63xx: replace SPI driver with latest upstream version
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31130 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28 20:42:25 +00:00
9daebe4304
bcm63xx: add ethernet support for bcm6368
...
Add basic support for the internal ethernet switch on bcm6368. It behaves
as a dumb switch for now, but allows basic connectivity.
Also drop the ethernet patch for bcm6345 for now, it needs rework.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31129 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28 20:42:20 +00:00
8dc562dfaa
bcm63xx: add missing bits from extirq support
...
Add missing external IRQ code parts for older chips in the new code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31128 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28 20:42:15 +00:00
f6e63fd141
bcm63xx: reorder patches
...
Reorder patches for a clearer distinction between the purposes of
the different patches.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31127 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-28 20:42:09 +00:00
887c0ecd98
targets: replace madwifi in profiles with ath5k, madwifi is unmaintained
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31015 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-19 09:58:13 +00:00
3815238ec6
[brcm63xx] remove udc patch since it is unused
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30920 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-13 14:06:44 +00:00
95137eb756
[brcm63xx] remove 3.1 support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30823 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-05 16:50:42 +00:00
1fdf0ff167
[brcm63xx] rename 96348GW-1{0,1}-gen to 96348GW-1{0,1}-generic
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30822 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-05 14:49:34 +00:00
8cd8278777
[brcm63xx] generate generic images for BCM96358VW and BCM96358VW2 ( #10666 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30821 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-05 14:49:31 +00:00
d49acac3eb
[brcm63xx] wire bcm96348gw-10 reset button ( #10854 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30820 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-05 14:23:45 +00:00
e6029cf3d7
Merge branch 'bcm63xx'
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30819 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-03-05 13:29:54 +00:00
395eb83d49
brcm63xx: add support for linux 3.3
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30027 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-02-04 10:17:27 +00:00
db12fa60c6
kernel: update linux 3.0 to 3.0.18
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29965 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-31 09:43:53 +00:00
61579d0934
[brcm63xx] build 96348R images
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29960 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-30 21:12:32 +00:00
58cd86efe5
[brcm63xx] remove support for 2.6.39
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29959 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-30 21:12:28 +00:00
c1defe3633
[brcm63xx] bump to 3.0.17
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29958 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-30 21:12:25 +00:00
4aabd3dd85
brcm63xx: add support for linux 3.2
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29731 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-13 14:59:50 +00:00
348b4546eb
kernel: update linux 3.1 to 3.1.9
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29726 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-13 14:38:28 +00:00
b2e991c3b2
kernel: update linux 3.0 to 3.0.17
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29725 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-13 14:10:44 +00:00
84cac8c91b
[brcm63xx] Remove invalid LED GPIO from GW6200 board definition. GPIO 35 isn't intended to control ethernet LED (the led behaviour is a side effect) and using the gpio as an led causes kernel panics.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29712 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-01-11 13:47:48 +00:00
3361c4d1bf
[brcm63xx] don't package gpioctl by default
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29288 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-21 16:36:39 +00:00
d724cd4a24
[brcm63xx] fix D-Link DSL-2650U image generation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29266 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-19 21:34:51 +00:00
16fd48e131
linux: update 3.0 to 3.0.9
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29264 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-19 18:39:12 +00:00
7d6a631816
[brcm63xx] build images for D-Link DSL-2650U ( #9003 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29238 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-18 10:37:03 +00:00
fb3e9ac6b0
[brcm63xx] build images for Pirelli A226M ( #10409 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29045 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:22 +00:00
150feffb3b
[brcm63xx] register uart0 on DWV-S0 boards ( #10409 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29044 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:18 +00:00
f849b5a225
[brcm63xx] rename 456-board_DWV-S0_ehci.patch to 456-board_DWV-S0_fixes.patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29041 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:05 +00:00
e30803b3df
linux: update 3.1 to 3.1.1
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29007 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 10:48:05 +00:00
0a7950b452
target: globally disable BSD process accounting
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28584 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-25 16:18:36 +00:00
ff1d70f47d
kernel: update kernel to version 2.6.39.4
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28022 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-16 22:04:10 +00:00
9518b7c8a1
[brcm63xx] fix ehci build on 3.0+
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27946 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-10 11:37:25 +00:00
d558e58172
[kernel] add ignore_oc in struct ehci_hcd
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27945 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-10 11:37:21 +00:00
4c03d36b1b
bcm63xx: add support for linux 3.1-rc1
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27941 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-09 12:19:49 +00:00
fc87157651
[brcm63xx] add support for BCM6345 Ethernet DMA engine
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27881 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-02 18:55:55 +00:00
c6242377bd
[brcm63xx] improve BCM6345 support
...
- runtime detect the amount of memory available
- define EBI_BASE as MPI_BASE to get rid of chip-select specific hacks
- fix GPIO control
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27880 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-02 18:55:46 +00:00
66421cdc87
bcm63xx: Fix SPI commands and register offsets for BCM6348
...
In 240-spi.patch, spi registers for bcm6348 were all messed up. This patch fixes that.
It also fixes some spi commands for all bcm63xx.
Signed-off-by: Anthony Blakemore <stokie-ant@raverbaby.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27774 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-25 19:52:47 +00:00
f780ffc6fd
[brcm63xx] add ehci support to DWV-S0 board ( #9059 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27622 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-16 08:39:04 +00:00
1218fd06fb
[brcm63xx] fix GEN_SPI_RSET_BASE macro ( #9697 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27604 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-13 09:33:11 +00:00
88704d73bb
[brcm63xx] move board_HW553 inside the ifdef ..BCM6358 .. endif block
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27484 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-06 10:00:39 +00:00
297aefe3b4
[brcm63xx] Makefile: fixed inclusion of kmod-leds-gpio as a module (breaks Image Generator) - the module is built into the kernel.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27471 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-06 06:35:24 +00:00
81e08b77c2
[brcm63xx] profiles: GW6X00: fixed inclusion of both wl and wlc wireless tools...should be just wlc
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27470 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-06 06:35:22 +00:00
5e1e039c45
[brcm63xx] hw553: fix missing has_uart0 in board definition ( #9533 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27448 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-07-04 15:04:58 +00:00
210af3e57c
kernel: update kernel to 2.6.39.2
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27298 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-28 19:30:58 +00:00
b5051f91ff
kernel: update ssb and bcma to linux-next next-20110627
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27295 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-27 21:28:40 +00:00
fa61065873
[brcm63xx] remove gpiodev, prefer sysfs gpio
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27284 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-25 19:26:17 +00:00
d72a90ee7b
[brcm63xx] register SSB sprom after ethernet devices
...
In case the MAC address pool is not big enough to also register a SSB SPROM
prefer registering the Ethernet devices.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27258 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-22 12:32:03 +00:00
16a2b890cf
[brcm63xx] fix tab damage in 141-led_count.patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27254 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-21 20:52:58 +00:00
a104f95d05
[kernel] fix and make usable kmod-pcmcia-rsrc
...
This module is also needed for e.g: kmod-bcm63xx-pcmcia
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27253 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-21 20:52:53 +00:00
46c6ee1ca7
[brcm63xx] use macros to generate SPI registers table and switches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27246 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-21 10:05:51 +00:00
d2e81efd80
[brcm63xx] dev-spi.c checks for running CPU, not board code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27236 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19 20:46:00 +00:00
35faebfc51
[brcm63xx] fixup patches after r27234
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27235 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19 20:28:38 +00:00
333e68fdfd
[brcm63xx] remove accidental bcm6345 related patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27234 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19 20:16:59 +00:00
f41477ce57
[brcm63xx] remove support for 2.6.37 and 2.6.38
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27233 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19 20:14:22 +00:00
0103e97008
[brcm63xx] switch to 2.6.39
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27232 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-19 20:12:45 +00:00
ab7d434b54
bcm63xx: Add support for Linux 3.0-rc3
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27192 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-06-16 14:34:40 +00:00
8cdbf2c4b6
bcm63xx: Add support for 2.6.39
...
Add support for Kernel 2.6.39. Boots fine on a BCM6358.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27019 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-27 09:54:52 +00:00
8dbfe7ca11
bcm63xx: Add support for 2.6.38
...
Add support for Kernel 2.6.38, based on 2.6.38.6. Boots fine on a BCM6358.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27018 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-27 09:54:48 +00:00
e95dc4b5c1
[brcm63xx] fold 446-board-D4PW_correction.patch in 440-board-D4PW.patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27014 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-26 13:53:00 +00:00
f1e6eb88e8
[brcm63xx] renumber patches accordingly
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27013 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-26 13:52:56 +00:00
9601ce7e1f
[brcm63xx] renumber board patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@27012 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-26 12:09:15 +00:00
195f49f69c
[brcm63xx] add support for BT Voyager 2110 ( #8810 )
...
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26959 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-20 10:06:25 +00:00
c24a32df6f
[brcm63xx] add support for DSL-2640B rev B2
...
Signed-off-by: Adrian Feliks <mexit@o2.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26958 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-20 10:06:22 +00:00
4b5cddfaca
[brcm63xx] refresh patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26957 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-20 10:06:18 +00:00
a6aa5507e7
[brcm63xx] add support for D-Link DVA-G3810BN/TL
...
This patch adds support for D-Link's DVA-G3810BN/TL product.
Signed-off-by: Roman Dumycz <roman@secureas.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26956 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-20 10:06:15 +00:00
764614896e
[brcm63xx] add support for BT Voyager 2500 ( #9070 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26954 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-20 10:06:07 +00:00
05bf83accb
[brcm63xx] add support for USR9108 LEDs ( #9372 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26953 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-20 10:06:04 +00:00
0da640db3b
bcm63xx: Add support for the T-Home Speedport W 303V
...
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26878 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-11 13:34:14 +00:00
93e4186e52
bcm63xx: Update support for the DSL-274xB revision C
...
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26876 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-11 13:33:50 +00:00
bc014cb9cd
bcm63xx: Accept any led with power in its name as power led
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26875 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-11 13:33:45 +00:00
2811523f2c
bcm63xx: Decouple Board ID and image name for fixup
...
Make the fixup board ID independent from the image name to allow using
the same board ID for similar devices.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26874 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-11 13:33:41 +00:00
b8f0b2b785
[kernel] fill maintainer infos for a couple of targets
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26836 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-06 12:37:36 +00:00
580cad4b9b
brcm47xx: when detecting a ssb pci device without an own sprom write the sprom data from the platform device to the correct pointer.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26829 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-05 14:05:21 +00:00
a6d76eb003
brcm47xx: add fallback sprom for pci devices without an own sprom.
...
If there is no sprom on an ssb based pci device on the brcm47xx
architecture ssb now asks the architecture code to look into the nvram
to get some sprom data for this device. Now we are able to read out
pci/1/1/ foo or pci/1/3/ foo config options.
This will fix some problems where the wireless devices does not got an
mac address and the following message was show:
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26801 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-05-01 20:28:35 +00:00
026165ed70
brcm63xx: remove patches/configs for 2.6.35
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26709 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-17 18:39:46 +00:00
2bfbe9f602
[brcm63xx] Fixed directory error: added ra1320 patches to trunk/target... subdir instead if target.... in trunk branch.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26699 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-17 01:15:47 +00:00
7c6472a3db
[brcm63xx] Generate images for RTA1320_16M-based routers
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26681 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-15 14:31:36 +00:00
b2ae50ed27
bcm63xx: Move the OpenWrt rootfs length field
...
Dual image capable CFEs store an image sequence at the same place as
currently OpenWrt stores the actual rootfs length, so it will get
overwritten when flashing through such a CFE.
To prevent this from happening, move the rootfs length field to the next
four bytes, thus completely using the reserved1 field.
Since the reserved1 field is now completely in use, it does not make sense
to allow it to be set from the imagetag utility, so remove the option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26680 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-15 12:18:25 +00:00
5fb18eaef8
kernel: Update to version 2.6.37.6
...
Thank you Peter Wagner for the patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26441 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-04-03 13:59:07 +00:00
5a76d52bf8
[brcm63xx] Updated kernel version to 2.6.37.4. Tested with 6348 and 6358 devices.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@26387 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-03-31 06:16:23 +00:00
e844751afa
bcm63xx: Really fix the flash driver in 2.6.37
...
Read back the actual rootfs length from the image tag.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25938 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-03-07 16:55:01 +00:00
78f95daf33
[brcm63xx] fix patches after 2.6.37 update, patch from KanjiMonster
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25810 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-03-01 16:02:38 +00:00
7bfdfcc4bd
[brcm63xx] add support for 2.6.37, patches from KanjiMonster
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25629 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-02-20 19:59:22 +00:00
2ec15bd5be
[brcm63xx] add support for HW553 bcm6358-based boards ( #8844 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25590 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-02-19 15:44:06 +00:00
3cea035cac
[brcm63xx] add support for 'MAGIC' bcm6348-based board
...
I wrote a patch to add 96348SV board (aka MAGIC) support to trunk.
In my case I've found it in a Telsey "Alice W-Gate" router, fairly common
(in the past) in Italy.
I used the board definition (GPIOs, leds, ...) from the Broadcom GPL-2
relased code (here is a mirror: http://beghiero.myftp.org/sorgenti/boardparms.c )
Thanks to KanjiMonster for the support on the IRC channel.
Signed-off-by: Laurento Frittella <laurento.frittella@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25584 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-02-19 12:44:27 +00:00
0a5005e824
[kernel] update to 2.6.35.11
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25582 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-02-19 12:44:16 +00:00
239a77ed96
[brcm63xx] fix T-Com Speedport W 500V default config
...
The device is called SPW500V, not SP500W.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25431 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-02-09 13:09:02 +00:00
405d9f27b2
[brcm63xx] fix build of brcm-wl
...
The fallback needs to be exported for bcm63xx, too. Runtime tested with a
BCM4322 on a BCM6358.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25420 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-02-08 13:46:12 +00:00
4e2d90b5b8
[brcm63xx] give some credits to Tanguy Bouzeloc in the spi driver
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25133 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-01-27 02:11:08 +00:00
29481143bf
[brcm63xx] multiple SPI driver fixes
...
- fix platform device registration
- fix chipselect, command register defines, add missing clock
- make slave select proper
- fix multibytes transferts
Signed-off-by: Tanguy Bouzéloc <tanguy.bouzeloc@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24849 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-29 16:19:59 +00:00
a6ec44df02
[brcm63xx] patches-2.6.35: mtd flashmap: Really fixed sparelen and rootfslen. The real rootfslen for OpenWRT images comes from a bigendian uint32_t in reserved1 of the bcm_tag, which is now used to correctly calculate the rootfslen (and thus the sparelen).
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24843 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-28 08:10:32 +00:00
cec3802964
[brcm63xx] patches-2.6.36: Fix flashmap spare length calculation from previous commit (for rootfs and rootfs_data mtd partitions). Apparently the interruption in working on it resulted in an incorrect memory of getting it working.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24842 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-28 04:05:04 +00:00
62f90595e1
[brcm63xx] spi driver: remove bcm_rset usage
...
Since bcm636x platform embeds two spi master device,
the attached patch removes static bcm_rset usage, replaced by
"bs->regs" field for all I/O operation.
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24840 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-28 00:24:50 +00:00
ec103967cb
Added OpenWRT-specific field to imagetag so that we can record the real root length, so that when the CRC fixup is applied and the root length is recorded as zero we can still calculate the rootfs mtd partition size.
...
Signed-off-by: Daniel Dickinson <daniel@cshore.neomailbox.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24838 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-26 04:18:13 +00:00
dda75774e9
base-files: Added uci-defaults script to run mtd fixtrx on firstboot for devices that need it.
...
Signed-off-by: Daniel Dickinson <daniel@cshore.neomailbox.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24836 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-26 04:18:04 +00:00
d93fac4436
mtd flashmap: Switched to calculating the rootfs size rather than depending on being given the size in the imagetag. This is because solving the problem of second boot CRC errors requires changeing the rootfs size in the image to zero.
...
Signed-off-by: Daniel Dickinson <daniel@cshore.neomailbox.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24834 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-26 04:17:56 +00:00
16c44de3e9
[brcm63xx] Fixed Comtrend CT536_CT5621 board settings. These boards are based on the 96348GW-11 reference design but have different GPIOs therefore we use the board fixups now availabed (thanks the patches by Jonas Gorski) to create a separate board entry for these boards and leave the reference design with reference GPIOs. Also these boards only have enet1 (no enet0) so we set that in the board definition, and use a defconfig for a single interface network.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24442 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-10 18:59:58 +00:00
7b9da8d0b0
[brcm63xx] Profiles: GW6X00: Replace ext2 module with ext4 as ext2 and 3 are going away. Remove kmod-loop as the need for it has been superseded by block-extroot, and remove kmod-fs-vfat as it takes space and is rarely needed.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24316 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-08 00:40:31 +00:00
de92064134
[brcm63xx] Profiles: Make buttons and led modules included by default so that failsafe will work in the case of builds for releases.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24315 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-08 00:40:28 +00:00
374672d6c0
[brcm63xx] Profiles: Move wpad-mini to the profiles that use it, rather than default for all profiles (because -wpad-mini means it's not selectable, which isn't what we always want for the No WiFi profile
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24314 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-08 00:40:24 +00:00
75c9c63874
[brcm63xx] patches: Renamed 150-led_count to 141-led_count so it comes before the 15-alice_gate2_leds.patch as which led count was mistakenly given the same number.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24310 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07 17:32:29 +00:00
b32148f92f
Revert "[brcm63xx] patches-2.6.35: Added flash chip definition for Macronix MX29LV640T."
...
This reverts commit 43511418ae2771a6662a83a254f06e37f4ac19e5.
It belongs in generic not brcm63xx.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24308 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07 17:02:31 +00:00
cb1024cc90
[brcm63xx] patches-2.6.35: Added flash chip definition for Macronix MX29LV640T.
...
Thanks blunoise
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24307 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07 16:42:23 +00:00
194d1e24c0
[brcm63xx] boards: Added GW6x00 fixups and GPIOs. The GW6200 GPIOs are different than the reference design 96348GW so we use fixup to allow us to define the correct ones, also the GW6000 has no GPIO-controlled leds.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24305 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07 15:15:54 +00:00
efe3905b6c
[brcm63xx] patches: Refreshed patches after led_count
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24304 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07 15:15:51 +00:00
5ac34fd9f0
[brcm63xx] board definitions: Added patch for calculating led count, which was part of the patch removed in the previous commit
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24303 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07 15:15:47 +00:00
903d1b5311
[brcm63xx] Remove patch 140-new_bcm96348gw_leds because it is really the GW6200 leds, not the generic 96348GW. Another commit will add the GW6200 specific boardid and leds. This removal reverts the 96348GW leds to the reference design GPIOs.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24302 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-07 15:15:41 +00:00
5700d60a40
[brcm63xx] base-files: Added the preinit information for reset button and preinit indication led, and preinit interface
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24276 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-06 06:46:03 +00:00
6407278c23
[brcm63xx] board definition: Fixed CPVA642 LED definitions
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24275 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-06 06:45:57 +00:00
a67ee8325d
[brcm63xx] board definitions: Added CPVA642 GPIO leds and buttons and refreshed patches later in series due to fuzz
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24274 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-06 04:31:23 +00:00
36114ce181
[bcm63xx] base-files: Added network defconfig because board only has one ethernet (4-port switch)
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24273 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-12-06 02:01:08 +00:00
9b5364abf2
[brcm63xx] image Makefile: Corrected router imagename length limiting. Thanks KanjiMonster for reminding me.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24191 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28 22:13:00 +00:00
0c4e2c5526
bcm63xx: Add support for the T-Com Speedport W 500V.
...
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28 22:04:44 +00:00
68981f5d8e
bcm63xx: Add board id override fixup.
...
Add a fixup for the kernel to check the bcm tag of the image for a boardid in
the information1 field, and use that instead of the supplied one by cfe. This
is triggered by a + at the start of the information1 field.
Also modify the image generation to generate apropriately tagged images.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24189 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28 22:04:40 +00:00
e96cc39f19
bcm63xx: Finalize support for DSL-274xB, rev C2.
...
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28 22:04:36 +00:00
e21b57d529
bcm63xx: Allow 'colored' power leds.
...
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24187 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28 22:04:30 +00:00
94a1adaf05
bcm63xx: Don't hardcode the switch ethernet interface in preinit.
...
Currently eth1 is hardcoded as the expected interface switches in diagmode.
This patch replaces the eth1 with the ifname, and also directly tests if
the interface specified by ifname has a switch attached.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24186 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28 22:04:26 +00:00
f78d9eebba
bcm63xx: Add defconfigs.
...
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24185 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-28 22:04:19 +00:00
1ae1fb6b50
update to the latest stable kernels
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24136 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-24 18:50:11 +00:00
ed589945f0
[brcm63xx] image Makefile: Removed extraneous tab from Image/LimitName16 macro definition. The solves the strange whitespace in front of the image name in the info1 section
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24127 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-24 11:06:13 +00:00
53af0d5fbb
[brcm63xx] image: Limited image name put into the info1 field to 16 characters and eliminted the OpenWRT revision. This makes using the image (router) name as the board name possible, so that boards with same real boardid but different GPIOs can be detected and the correct GPIOs used.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24118 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-23 20:17:08 +00:00
4470bf532c
[brcm63xx] Initial support for Telsey CPVA642 boards (no vlans, no DSL, GPIO led/buttons not known).
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24040 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-19 13:41:54 +00:00
caefcca898
[tools/firmware-utils] imagetag: Significantly updated brcm63xx imagetag writing tool.
...
* Rewrote commandline parsing code using gengetopt
- We now get long options
- We have more options including use of the info section for
board information (e.g. to add the same boardid but
different GPIOs on different routers)
* Added back the ability to write stock images (this is useful, for example,
when copying the firmware from the in-memory flash, and then being
able to create an image that will let you revert to/test stock firmware
* Fixed copying of CRCs to use memcpy instead of strncpy (strncpy stops at 0)
* Added ability to use all sections of the imagetag, including custom magic
signatures (e.g. for the Telsey router I'm adding soon), info sections,
and reserved sections
* Added putting the router type (as defined in the image generating Makefile)
into the info1 section and the filesystem type in the info2 section.
This will be used by mtd (when I add the code) to return the name of
image used to flash this router. (As requested by Jo, as well as being
useful for same boardid different board scenario described above).
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-16 06:46:53 +00:00
dcc7bd0d17
[brcm63xx] Add wps button on alice gate
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23903 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-06 21:08:44 +00:00
a497060e39
update kernels to 2.6.32.25 and 2.6.35.8
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23851 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-11-04 09:01:08 +00:00
27c9658984
[brcm63xx] register uart driver on livebox ( #8013 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23653 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-27 10:02:13 +00:00
b024c3f927
[brcm63xx] refresh 2.6.35 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23652 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-27 10:02:08 +00:00
307bfbe677
[brcm63xx] Fix nxp_74hc164 driver compile error (builbot)
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23623 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-24 16:10:41 +00:00
4701c8448b
[brcm63xx] fix platform_devices registration
...
Signed-off-by: Tanguy Bouzéloc <tanguy.bouzeloc@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23517 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-18 19:49:54 +00:00
6591e5b4dd
[brcm63xx] add bcm96338W2 e7t board (D-Link 2640U/BRU/C, #7558 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23508 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 17:45:50 +00:00
f46ab7dcae
[brcm63xx] remove 2.6.32 support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23505 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 16:32:35 +00:00
f320f07d40
[brcm63xx] fix SPI driver, move register out of driver code
...
Signed-off-by: Tanguy Bouzéloc <tanguy.bouzeloc@efixo.com
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23504 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:09:30 +00:00
a52f0a386a
[brcm63xx] restore kernel oldconfig
...
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23503 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:09:24 +00:00
bfa00c8c0b
[brcm63xx] refresh patches
...
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23502 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:09:04 +00:00
5eb60cbbf7
[brcm63xx] refresh nb4 support. Register 74x164 device
...
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23501 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:08:57 +00:00
43a07c2197
[brcm63xx] add spi devices board info int bcm63xx_boards
...
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23500 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:08:51 +00:00
193172120b
[brcm63xx] add 74x164 SPI chip support
...
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23499 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:08:45 +00:00
7475affd50
[kernel] backport SPI master with no RXTX support (from 2.6.36)
...
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23498 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:08:39 +00:00
292e6071e4
[brcm63xx] register earlier extended platform devices
...
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23497 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-17 14:08:34 +00:00
dd2a52b3a0
[kernel] update 2.6.35.x to 2.6.35.7
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23213 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-10-04 07:42:32 +00:00
2e243c343e
[brcm63xx] remove wpa-supplicant and iw from the Tecom GW6x00 profile
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23051 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-09-13 08:30:35 +00:00
36ab483f47
[brcm63xx] default to using 2.6.35
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23038 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-09-12 21:23:53 +00:00
97a561ae31
[brcm63xx] remove 2.6.33 support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23037 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-09-12 21:23:47 +00:00
e79fccc1da
[brcm63xx] change the Tecom GW6x00 profile to use wl instead of b43
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23036 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-09-12 21:23:41 +00:00
61db512e5c
[brcm63xx] register udc and spi devices at the correct init level
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23035 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-09-12 21:23:35 +00:00
3506323f4a
[brcm63xx] refresh 2.6.35 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23034 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-09-12 21:23:29 +00:00
229d390a6c
[linux] enable SYSRQ for all targets, remove overrides from brcm63xx, octeon and omap35xx
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22846 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-30 22:59:20 +00:00
79cda87dc5
[brcm63xx] add 2.6.35 support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22800 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-25 19:56:08 +00:00
53fe275b46
[kernel] update to 2.6.32.20
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22766 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-22 17:07:37 +00:00
dfda352bca
[brcm63xx]: base-files: diag.sh: For power button as preinit status led, end with led left on, not off
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22466 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-02 19:33:08 +00:00
8b6a51edad
[brcm63xx] base-files: brcm63xx.sh: Added comtrend (96348GW-11) to routers with buttons and leds on preinit
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22465 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-02 19:32:59 +00:00
ba4b087197
[brcm63xx] patches-2.6.32/33: Reset button on Comtrend routers is GPIO 33 not GPIO 32
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22464 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-08-02 19:32:40 +00:00
514d70b175
[brcm63xx] reorder profiles
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22390 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-26 18:58:35 +00:00
80edf72017
[brcm63xx] fix a typo in 040-bcm963xx_flashmap.patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22386 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-25 00:10:37 +00:00
0b47979d12
update kernel versions
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22289 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-19 11:34:03 +00:00
c8c989694d
[brcm63xx] fix alice gate2 internet:green led ( #6743 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22273 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-18 10:29:44 +00:00
1cff76c4b1
[brcm63xx] add required exports for wl.ko
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22174 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-13 17:03:56 +00:00
33990405fb
massive: replace occurences of .$(LINUX_KMOD_SUFFIX) with .ko after r21950
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22145 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-12 14:06:13 +00:00
dc8d0d6700
[brcm63xx] add a wifi profile for proprietary wl
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@22009 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-07-01 01:39:04 +00:00
e5e370a876
[brcm63xx] add missing alice gate2 leds ( #6743 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21785 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-06-13 12:20:53 +00:00
924c09e04c
[brcm63xx] do not override cfg80211-related config symbols
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21769 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-06-12 18:10:16 +00:00
93df402589
generic: move more common options to generic configuration
...
* CONFIG_ABX500_CORE
* CONFIG_ATOMIC64_SELFTEST
* CONFIG_BRIDGE_IGMP_SNOOPING
* CONFIG_CAIF
* CONFIG_CEPH_FS
* CONFIG_CRYSTALHD
* CONFIG_DEFAULT_SECURITY_SELINUX
* CONFIG_DEFAULT_SECURITY_SMACK
* CONFIG_DEFAULT_SECURITY_TOMOYO
* CONFIG_DT3155
* CONFIG_IP_MROUTE_MULTIPLE_TABLES
* CONFIG_L2TP
* CONFIG_LOGFS
* CONFIG_LPC_SCH
* CONFIG_MFD_JANZ_CMODIO
* CONFIG_MFD_RDC321X
* CONFIG_N_GSM
* CONFIG_RAMOOPS
* CONFIG_SERIAL_ALTERA_JTAGUART
* CONFIG_SERIAL_ALTERA_UART
* CONFIG_SERIAL_TIMBERDALE
* CONFIG_SM_FTL
* CONFIG_SQUASHFS_XATTRS
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21750 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-06-10 10:45:51 +00:00
Florian Fainelli
John Crispin
Jonas Gorski
Gabor Juhos
Felix Fietkau
Daniel Dickinson
Jo-Philipp Wich
Hauke Mehrtens
Imre Kaloz
Claudio Mignanti
Lars-Peter Clausen