Change the autoload number from '5' to '05' so the module loads earlier (as intended).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38293 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38036 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Javier Achirica for the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38008 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38001 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37977 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most of the Linksys devices without an own GPIO configuration where
detected as WRT54G. On one board this made OpenWrt to boot into
failsafe every time, because one GPIO configurated as button was not a
button.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37970 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was itriggered by to many non buffalo devices
This closes#14043.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37804 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds button and led info, which I determined
by manually poking the gpio values.
Signed-off-by: Josh Stone <cuviper@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37655 3c298f89-4303-0410-b956-a3cf2f4a3e73
add the boot flag to make the kernel modules needed for Ethernet and
diag load on startup.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37284 3c298f89-4303-0410-b956-a3cf2f4a3e73
In kernel 3.10 the proc interface changed, this patch adds the changes needed for the new interface.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37280 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was done to reduce the number of forward declaration needed.
This does not contain any real change in the code.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37278 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hauke Mehrtens
John Crispin