This is a minor rework of the SDK driver. This driver needs a full rewrite.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38846 3c298f89-4303-0410-b956-a3cf2f4a3e73
get_cycles() is used in some places as one part of the seed for the
kernel PRNG.
This backports the following commit from mainline linux kernel:
9c9b415c50bc298ac61412dff856eae2f54889ee
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38834 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add the profile for the TP-LINK WR842N/ND v2
Small update, because of a change in the Makefile.
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4382/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38815 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add the user space support for the TL-WR842N/ND v2
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4354/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38814 3c298f89-4303-0410-b956-a3cf2f4a3e73
Get the factory assigned mac addresses stored in the caldata
partition and asign them to lan and wan interfaces. Also put
the correct mac addresses into the WiFi eeprom files to ensure
that the ath9k driver will use the correct ones.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Patchwork: http://patchwork.openwrt.org/patch/4350/
[juhosg:
- move WiFi MAC address setup to the firmware hotplug file,
- use the official MAC address for the 2.4GHz as well,
- remove uci-defaults.sh modifications,
- update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38812 3c298f89-4303-0410-b956-a3cf2f4a3e73
- update kernel to 3.12
- add patches for clocks, i2c, usb, sid, rtc
- support common image for A10/A13/A20
- add support for a couple boards
- most drivers are configured into the kernel as of now
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38811 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current implementation of mtd will not append the backup
file created by sysupgrade to the correct partition, as mtd will append
the data to first jffs2 partition it finds. As the kernel is also
stored on a jffs2 partition (which resides before the overlay
partition), the data will be appended to this partition.
To fix this problem, a new option
-s <number> skip the first n bytes when appending data to the jffs2 partiton, defaults to "0"
is added to mtd.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38807 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some devices are using tty1 as the default console, also swap the early
boot console in such case. This is needed for the WGT634U.
Thank you Russell for reporting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38794 3c298f89-4303-0410-b956-a3cf2f4a3e73
The BCM5365 needs a shift of 7 bits and not 6 bits like the BCM5325 for
the untagged ports.
Thank you Russell for reporting this and testing the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38793 3c298f89-4303-0410-b956-a3cf2f4a3e73
- enable building uboot for imx23 along sbImage by default
- (doc updated)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38781 3c298f89-4303-0410-b956-a3cf2f4a3e73
boardnum is unstable, so allow using NULL to make it unchecked.
A method for differentiating F7D3301 from F7D3302 using nvram is
unknown at this point. Reading the first 32bits of magic from the
"linux" mtd partition would do the trick, but these 2 are similar
enough that we don't need separate led/button definitions. Not knowing
which one you have is only a usability issue for upgrading the device:
they expect different magic numbers for their trx images.
Signed-off-by: Cody P Schafer <devel@codyps.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38767 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is a problem when phydev is not set at this position and not the other way around.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38744 3c298f89-4303-0410-b956-a3cf2f4a3e73
Just fixing up a few things for the Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38733 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add user space support for the TL-WA750RE/WA850RE range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38718 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38717 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes bgmac work without sprom and refreshed the patches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38715 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some more code for bgmac core rev 4 and it now restarts all
cores when initializing the first one on BCM4708. I am just able to
send under 100 packages and then DMA TX does not work any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38714 3c298f89-4303-0410-b956-a3cf2f4a3e73
This pci ID is used by sprom less BCM4313 devices.
This is a backport from the mainline kernel.
This is part of #13551.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38713 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is also known as BCM470{7,8,9}.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38712 3c298f89-4303-0410-b956-a3cf2f4a3e73
- add building of a standard uImage along with the combined kernel+rootfs
- remove 'old' image build - that was for a very old and obsolete bootloader
To update the bootloader for GW2387,GW2388,GW2391 (NOR Flash) from uboot:
put latest NOR bootloader on tftp server:
http://svn.gateworks.com/laguna/trunk/images/u-boot_nor.bin
Laguna> setenv ipaddr <localip>
Laguna> setenv ipaddr <serverip>
Laguna> tftpboot 0x800000 laguna/u-boot-nor.bin
Laguna> erase 0x10000000 +$(filesize)
Laguna> cp.b 0x800000 0x10000000 $(filesize)
Laguna> reset
To update the bootloader for GW2380,GW2382,GW2383 (SPI Flash) from uboot:
put latest SPI bootloader on tftp server:
http://svn.gateworks.com/laguna/trunk/images/u-boot_spi.bin
Laguna> setenv ipaddr <localip>
Laguna> setenv ipaddr <serverip>
Laguna> tftpboot 0x800000 laguna/u-boot-spi.bin
Laguna> erase 0x60000000 +$(filesize)
Laguna> cp.b 0x800000 0x60000000 $(filesize)
Laguna> reset
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38703 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38699 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
The GPIO bit banging protocol implementation was copied from the old
switch driver and adapted to this driver and changed to the mainline
kernel GPIO interface.
The ADM6996L is different from the ADM6996M which is supported, for
both specs are available in the Internet.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38698 3c298f89-4303-0410-b956-a3cf2f4a3e73
In particular, phy_connect before register_netdev. This is because
register_netdev runs the netdev notifiers, which can race with the rest of
the initialization in ag71xx_probe. In my case this manifested in two ways:
1) If ag71xx is compiled as a module and inserted after netifd has started,
netifd is notified by register_netdev before the call to
ag71xx_phy_connect. netifd tries to bring the interface up, which calls
ag71xx_open, which in turn enters ag71xx_phy_start. This keys off
ag->phy_dev (which is still NULL) and thinks this is a fixed-link board,
and enters ag71xx_link_adjust. This looks at ag->speed which is not yet
initialized and hits the BUG() in the switch (ag->speed) in
ag71xx_link_adjust.
This is the wrong code path for ag71xx_phy_start - my board has PHYs that
need to be brought up with phy_start. Doing ag71xx_phy_connect before
register_netdev ensures that ag->phy_dev is non-NULL before
ag71xx_phy_start is ever called.
2) When ag71xx is built into the kernel, and netconsole is enabled, there
is a gap in the initial burst of replayed printks right after the netdev
comes up. My assumption is that netconsole is also triggered by a netdev
notifier, and part of this printk burst happens before the call into
ag71xx_phy_connect, so part of the burst is lost while the PHY comes up.
This patch fixes the gap - all the printks before eth0 comes up are bursted
in full when netconsole initializes.
ag71xx_phy_connect_xxx no longer runs with a registered netdev, so the
logging has been adjusted accordingly to avoid "unregistered net_device" or
"eth%d" messages in dmesg.
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38689 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg:
- remove the Image/Build/CyberTANLZMA/loader macro, it is not used
- move the MYNETREXT SingleProfile definition to the correct place]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38688 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38686 3c298f89-4303-0410-b956-a3cf2f4a3e73
Append EOF markers to the END of the UBI image
file. This forces the kernel to erase all blocks
after the marker even if those blocks are not
empty.
Additionally, the resulting image can be flashed
from the original web UI now, so use '-factory'
suffix for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38683 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch should prevent overriding of sysupgrade binaries in the bin directory
if we build images for more then one file system type.
Discussion:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-October/022108.html
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38674 3c298f89-4303-0410-b956-a3cf2f4a3e73
The switch is renamed to "switch0" in newer (3.10) linux kernels.
Configure the switch using vlans by default and only configure
the physical switch ports that are present.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38673 3c298f89-4303-0410-b956-a3cf2f4a3e73
Extended the Makefile to generate a working factory reset image
for Netgear WNDR4300. The image uses UBI with two volumes squashfs
(rootfs) and JFFS2 (rootfs_data). In order to make stock U-Boot
happy, a fake rootfs image is placed into the last erase block
of the kernel partition.
Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
- restore the NetgearNAND/initramfs macro,
- remove unused {Squash,Ubi}fsTemplate macros,
- remove board specific mtd options from CONFIG_CMDLINE, append the
board specific ubi.mtd parameter to the kernel command line instead,
- increase kernel partition size to 2MiB,
- use board specific ini file for ubinize,
- put jffs2 eof mark into the rootfs_data ubi volume,
- use KDIR_TMP for temporary images,
- use the squashfs-raw image,
- increase kernel partition size to 2MiB,
- use a local ubinize macro,
- fix macro parameter comments,
- put the fake rootfs into the last erase block of the kernel
partition,
- move Image/Build/NetgearNAND/buildkernel macro before
define Image/Build/NetgearNAND,
- don't use the wndr3700 utility, use '-M' parameter of mkimage to set
the uImage magic,
- use '-recovery' suffix for the generated image, it is only usable via
the fw_recovery function of the bootloader,
- update commit log]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38655 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add new subtarget nand with UBI/UBIFS including GLUEBI and squashfs.
This target will be used for NAND based router which make use of
UBI (and maybe UBIFS later on) in order to provide proper NAND
support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
- tweak target.mk:
change BOARDNAME variable,
improve Target/Description,
remove targz and ubifs from FEATURES and add broken flag,
- optimize kernel configuration:
disable ubifs, it is not used yet,
disable unused MTD options,
disable SPI support
disable unused network drivers,
tune kernel command line,
- remove image/ubinize.cfg, it will be in a follow-up patch
- move profile modifications into a separate patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38646 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current code only allows to automatically set
root device on MTD partitions. Move the code to MTD
core to allow to use it with all MTD devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38643 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some more bgmac patches from mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38637 3c298f89-4303-0410-b956-a3cf2f4a3e73
Ensures that the 'Default' images are generated
even if the subtarget has no profiles.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38635 3c298f89-4303-0410-b956-a3cf2f4a3e73
The buildbots found some new missing config options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38633 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds the userland support for the Pogoplug E02 by Cloud
Engines, Inc.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38631 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds a DTS file for the Pogoplug E02 by Cloud Engines, Inc.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38630 3c298f89-4303-0410-b956-a3cf2f4a3e73
* use lower case letters in generated images
* extend support for boot/ directory
* fix some typos
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38629 3c298f89-4303-0410-b956-a3cf2f4a3e73
Changes include PCI fixes and various upstream pending patches.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38624 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was spotted by the buildbots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38604 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TEW-692GR images are missing since r36169. Uncomment
the board specific macro in image/Makefile, in order to
generate those again.
Only build tested. No idea if the the image works or not,
I have bricked my TEW-692GR a few months ago.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38603 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- remove MultiProfile, it makes no sense for a single board
- move SingleProfile call and the mtdlayout to a different
location keep things sorted (well, almost)]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38593 3c298f89-4303-0410-b956-a3cf2f4a3e73
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- rename and refresh kernel patch,
- fix some checkpatch warnings and adjust whitespaces in
mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38591 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).
1. http://svn.dragino.com/dragino2
Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
- rename and refresh kernel patch,
- fix checkpatch warnings in mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38587 3c298f89-4303-0410-b956-a3cf2f4a3e73
Upstream commit c655bc6896b94ee0223393f26155c6daf1e2d148 changed number of
arguments in nf_ct_iterate_cleanup() function.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38547 3c298f89-4303-0410-b956-a3cf2f4a3e73
Pins with no mux option failed to be recognized as gpios.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38540 3c298f89-4303-0410-b956-a3cf2f4a3e73
When the mdio bus is unregistered the newly created phy will also be
unregistered and freed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38539 3c298f89-4303-0410-b956-a3cf2f4a3e73
On some devices with e.g. a BCM2535F switch the second MAC is used, but
we can not find a phy under all addresses between 0 and 31, 0xffffffff
is returned as phy id. If we can not find a phy at the expected address
create a dummy one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38538 3c298f89-4303-0410-b956-a3cf2f4a3e73
Upstream commit 9ddebc46 ("MIPS: OCTEON: Rename Kconfig
CAVIUM_OCTEON_REFERENCE_BOARD to CAVIUM_OCTEON_SOC") renamed a Kconfig
symbol, thus making all MIPS builds ask for this specific Kconfig
symbol, add it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38535 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the warnings and errors reported by checkpatch on swconfig.c
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38523 3c298f89-4303-0410-b956-a3cf2f4a3e73
The interrupt mapping for legacy interrupts was backwards causing interrupts
to be mapped improperly behind a PCIe to PCI bridge (ie GW16082 mezzanine).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38519 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable SATA support (for IMX6D/IMX6Q) static in the kernel. It seems there
are some issues causing the driver to not load properly when built as
a module which still need to be worked out.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38515 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add upstream patches needed for PCIe through a switch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38511 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is for Mikrotik devices only, rename the subtarget
to reflect that. Also fix the wget2nand script to use
the new image names.
Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38509 3c298f89-4303-0410-b956-a3cf2f4a3e73
The nand subtarget supports Mikrotik boards only. Change
the title and the description to reflect that.
Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38508 3c298f89-4303-0410-b956-a3cf2f4a3e73
Ensure that menuconfig shows the correct help text for
subtargets.
Based on the patch by Stefan Agner:
http://patchwork.openwrt.org/patch/4123/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38507 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this patch we treated only phy addr 30 as an external phy, but
there is a register to check that. Now we do not have to try to reset
the switch to check for an external switch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38502 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on 'kernel: update x86 generic to 3.10.13' patch
from http://patchwork.openwrt.org/patch/4129/
Signed-off-by: Ulrich Weber <uw@xyne.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38500 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on 'kernel: update x86 generic to 3.10.13' patch
from http://patchwork.openwrt.org/patch/4129/
Signed-off-by: Ulrich Weber <uw@xyne.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38499 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on 'kernel: update x86 generic to 3.10.13' patch
from http://patchwork.openwrt.org/patch/4129/
Signed-off-by: Ulrich Weber <uw@xyne.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38498 3c298f89-4303-0410-b956-a3cf2f4a3e73
Both Allnet and OpenMesh sysupgrade uses fw_setenv from uboot-envtools to
change different settings in the uboot environment. uboot-envtools version
2013.01 introduced a filesystem lock "/var/lock/fw_printenv.lock" to guarantee
mutually exclusive access to the uboot environment. But the path /var doesn't
exist on the sysupgrade ramfs.
An upgrade on these devices fails since r36033 ("[package] uboot-envtools:
upgrade to version 2013.01.01") with following messages:
Error opening lock file /var/lock/fw_printenv.lock
failed to update U-Boot environment
Creating the "/var/lock" path before running fw_setenv is therefore a
requirement unless the locking functionality in fw_setenv is removed or
replaced with optional locking.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38483 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes the 5 GHz LED.
The same function has no effect on the 2.4 GHz LED at all, so we might
as well remove it.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38482 3c298f89-4303-0410-b956-a3cf2f4a3e73
TARGET_x86_generic_Soekris48xx is not defined,
CONFIG_TARGET_x86_generic_Soekris48xx is
This changes makes it possible to override the network config for soekris net48xx
and net45xx targets.
Signed-off-by: Bruno Randolf <br1@einfach.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38450 3c298f89-4303-0410-b956-a3cf2f4a3e73
Changes include:
* switching to profiles
* adding ubifs support
* building image for GW54XX board
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38441 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this patch, the patch
target/linux/generic/patches-3.10/770-bgmac-backport.patch
would not apply.
Signed-off-by: Tobias Steinicke <tsteinicke@net.t-labs.tu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38438 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixed voltage regulator support is required by several drivers that have
regulator consumers, such as the sgtl5000 audio codec used on many i.MX6
boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38426 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Gateworks GW51xx family of products is based on the Freescale
i.MX6DL SoC and offers a small form-factor with peripherals such as:
* i.MX6DL 512MB DDR3
* 256MB NAND FLASH
* 2x PCIe
* 1x USB EHCI (to PCIe socket2)
* 1x USB OTG (to front panel or PCIe socket1)
* 1x uSD
* LVDS
* HDMI AudioVideo out
* Analog Video in
* Digital IO
* Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38425 3c298f89-4303-0410-b956-a3cf2f4a3e73
They make our life easier when testing ramdisk images.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38420 3c298f89-4303-0410-b956-a3cf2f4a3e73
This just add some bytes to the kernel and is activated on other targets.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38388 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without specifying -march gcc uses -march=mips1 by default, but that
causes problems when compiling openssl. Use -march=r5000 instead to
compile a userland optimized for the CPU used on this device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38386 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some more boards.
This fixes parts of #14316 and #14133.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38383 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now it is possible to build ubi/ubifs images for only selected boards inside
single target.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38375 3c298f89-4303-0410-b956-a3cf2f4a3e73
Linux 3.9 is EOL since quite a while, no need to keep support for it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38370 3c298f89-4303-0410-b956-a3cf2f4a3e73
Run tested on WAG354Gv2.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38369 3c298f89-4303-0410-b956-a3cf2f4a3e73
Commit r37470 did not add a default conig for the ARM_ERRATA symbols for kernel 3.3.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38352 3c298f89-4303-0410-b956-a3cf2f4a3e73
init no longer exists as a parameter
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38342 3c298f89-4303-0410-b956-a3cf2f4a3e73
sizeof when applied to a pointer typed expression gives the size of the
pointer.
Found by coccinelle spatch "misc/noderef.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38312 3c298f89-4303-0410-b956-a3cf2f4a3e73
Early printk was disabled because it caused hangs on some devices, the
old patches were using the CFE console now we use the normal serial
console, it is at a constant address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38309 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add patches like they are currently in the mainline mips tree and add
some more pending patches for board detection.
* Now the board name is shown under machine in /proc/cpuinfo.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38308 3c298f89-4303-0410-b956-a3cf2f4a3e73
* do not try initialize a unused phy
* some improvements to the phylib patch
* do not turn the phy off when mac is off
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38306 3c298f89-4303-0410-b956-a3cf2f4a3e73
In 3.10 we might build those, so for now just add this functionality.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38297 3c298f89-4303-0410-b956-a3cf2f4a3e73
Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38294 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bool logic was the wrong way around.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38292 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bgmac driver will be used on the brcm47xx and the bcm53xx target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38289 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bgmac driver will be used on the brcm47xx and the bcm53xx target.
These are only the patches already applied in current net-next/master
branch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38288 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport appropriate patches to allow using device tree only board
defintions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38280 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is not supported by the controller.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38234 3c298f89-4303-0410-b956-a3cf2f4a3e73
vfp3 should be named vfpv3
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38222 3c298f89-4303-0410-b956-a3cf2f4a3e73
use the srab switch driver on these SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38200 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the bgmac driver with the patches already used for bcm47xx target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38199 3c298f89-4303-0410-b956-a3cf2f4a3e73
The SRAB interface is used on BCM4707 and BCM5301X SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38198 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is in preparation for sysupgrade support for Compex devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38197 3c298f89-4303-0410-b956-a3cf2f4a3e73
- remove the kernel+rootfs partitions from the MTD partition map,
- use a temporary directory for intermediate image files,
- append the root squashfs directly to the kernel,
- don't hardcode uImage size in the jffs2 images,
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38194 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the image building code so that the kernel correctly
distinguishes between hardware revisions.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38192 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.
Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38190 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Gateworks GW51xx family of products is based on the Freescale
i.MX6DL SoC and offers a small form-factor with peripherals such as:
- i.MX6DL 512MB DDR3
- 256MB NAND FLASH
- 1x PCIe
- 1x USB EHCI (to PCIe socket)
- 1x USB OTG
- HDMI out
- Analog Video in
- Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38189 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Gateworks GW54xx family of products is based on the Freescale
i.MX6Q SoC and offers a large variety of peripherals such as:
- i.MX6Q 1GB DDR3 (standard)
- 256MB NAND FLASH (standard)
- 6x PCIe (3x with USB)
- Optional expansion for additional USB/PCI based periperhals
- 1x USB EHCI
- 1x USB OTG
- HDMI Audio/Video in/out
- Analog Video in/out
- Analog Audio in/out
- Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38188 3c298f89-4303-0410-b956-a3cf2f4a3e73
During a reset the gpiolib warns about using the reset gpio
without explicit requesting it before:
[ 147.930000] ------------[ cut here ]------------
[ 147.930000] WARNING: at drivers/gpio/gpiolib.c:103 gpio_ensure_requested+0x68/0xcc()
[ 147.930000] autorequest GPIO-5
[ 147.930000] Modules linked in: ath5k ath mac80211 ipv6 cfg80211 compat arc4 crypto_blkcipher aead gpio_button_hotplug
[ 147.930000] Call Trace:
[ 147.930000] [<8004e3bc>] dump_stack+0x8/0x34
[ 147.930000] [<80058430>] warn_slowpath_common+0x78/0xa4
[ 147.930000] [<800584e4>] warn_slowpath_fmt+0x2c/0x38
[ 147.930000] [<80166f18>] gpio_ensure_requested+0x68/0xcc
[ 147.930000] [<80167264>] gpio_direction_output+0xdc/0x168
[ 147.930000] [<8004aba8>] ar2315_restart+0x28/0x54
[ 147.930000] [<80069778>] sys_reboot+0x178/0x1c0
[ 147.930000] [<80043670>] stack_done+0x20/0x40
[ 147.930000]
[ 147.930000] ---[ end trace 2c7a53d8549562d6 ]---
This is fixed with this patch by using another gpiolib api call
which includes the missing request.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38183 3c298f89-4303-0410-b956-a3cf2f4a3e73
It works:
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r38163)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# uname -a
Linux OpenWrt 3.10.12 #1 Tue Sep 24 18:47:12 CEST 2013 avr32 GNU/Linux
root@OpenWrt:/# cat /proc/cpuinfo
processor : 0
chip type : AT32AP700x revision C
cpu arch : AVR32B revision 1
cpu core : AP7 revision 0
cpu MHz : 140.000
i-cache : 16K (4 ways x 128 sets x 32)
d-cache : 16K (4 ways x 128 sets x 32)
features : dsp simd ocd perfctr java
bogomips : 281.23
root@OpenWrt:/#
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38174 3c298f89-4303-0410-b956-a3cf2f4a3e73
Compile tested only. The target is marked as
broken since 16 months so the kernel version
does not matter too much.
The target is scheduled for removal.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38162 3c298f89-4303-0410-b956-a3cf2f4a3e73
Compile tested only. The target is marked as
broken since 9 months so the kernel version
does not matter too much.
The target is scheduled for removal.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38159 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the kernel and rootfs partitions. The Seama
parser can find those automatically:
0x000000070000-0x000000ff0000 : "firmware"
2 seama-fw partitions found on MTD device firmware
0x000000070000-0x0000001b0000 : "kernel"
0x0000001b0000-0x000000ff0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
1 squashfs-split partitions found on MTD device rootfs
0x000000360000-0x000000ff0000 : "rootfs_data"
0x000000ff0000-0x000001000000 : "radiocfg"
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38155 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used for the WD My Net N600 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38154 3c298f89-4303-0410-b956-a3cf2f4a3e73
- append the root squashfs directly after the kernel,
- use the 64kraw/128kraw template instead of the 64k/128k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on WZR-HP-G300NH and WZR-600DHP boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38153 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Image/Build/WZRHP64K and the Image/Build/WZRHP128K macros
are similar. Move the common stuff into the Image/Build/WZRHP
macro and update the orignal macros to use that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38152 3c298f89-4303-0410-b956-a3cf2f4a3e73
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a TEW-673GRU board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38151 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Image/Build/DIR825B1 and the Image/Build/DLRTDEV macros
are identical. Merge those into a new Image/Build/CameoAP94
macro, and update the device profiles to use the new macro.
Also rename the dir825b1_* mtdlayout macros to cameo_ap94_*.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38150 3c298f89-4303-0410-b956-a3cf2f4a3e73
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a WispStation M5 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38148 3c298f89-4303-0410-b956-a3cf2f4a3e73
The firmware generation part is the same for both
macros. Move that into a separate macro and use the
new macro for Image/Build/UB{NTXM,DEV}.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38146 3c298f89-4303-0410-b956-a3cf2f4a3e73
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on the WHR-G301N board only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38141 3c298f89-4303-0410-b956-a3cf2f4a3e73
- remove the 'kernel' and 'rootfs' partitions from the mtd layout,
- move the .okli image into the uImage,
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on the MZK-W300NH board only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38139 3c298f89-4303-0410-b956-a3cf2f4a3e73
- append the root squashfs directly to the kernel,
- use the 64kraw-nojffs template instead of sqashfs-only
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a TEW-712BR devices only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38130 3c298f89-4303-0410-b956-a3cf2f4a3e73
- append the root squashfs directly to the kernel,
- use the 64kraw/64kraw-nojffs template instead of 64k/squashfs-only,
- ensure, that the signature is placed at the correct offset in
the *-factory images,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on DIR-600-A1 and TEW-632BR devices only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38129 3c298f89-4303-0410-b956-a3cf2f4a3e73
The MTD layout of the AP99 based devices is different.
Add new macros to reflect that and use the new macros
for the DIR-615-E4 board.
This prevents overwriting of the 'mac' partition which
contain vital informations. The disadvantage of the change
is that the usable space is reduced by 192KiB. Blame the
vendors for the unfriendly partition layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38128 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the reference board name in the macro
instead of the SoC number.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38127 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also remove the similar code from the Netgear
profile and use the new feature instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38126 3c298f89-4303-0410-b956-a3cf2f4a3e73
- remove the kernel and rootfs partitions from the mtd layout,
the kernel creates those automatically,
- remove estimation step, it is not needed anymore
- put the root squashfs directly after the kernel
- use the 64kraw template
With the default configuration, this allows to use more space for
rootfs_data with 64KiB. Tested on WNDR3700 v1 only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38120 3c298f89-4303-0410-b956-a3cf2f4a3e73
The new macro will be used to determine the firmware
partition size from an MTD layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38117 3c298f89-4303-0410-b956-a3cf2f4a3e73
Improve the macro to return correct value for
all squashfs variant.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38116 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make it possible to append the rootfs image directly
to the kernel.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38115 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the wlan2g led in the default configuration of dir-825-c1.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4079/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38106 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch
- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
(wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
explicit
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38105 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make it consistent with the other Netgear boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38103 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable GPIO 20. This hands off control of the blue planet led to the
integrated switch. Consequently, remove the led configuration for the
blue planet led.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4080/
[juhosg: whitespace fixup]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38096 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows to build images for other boards, even if
the image is too big for Cameo devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38095 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patches fixes the lan led configuration. The new configuration is
identical to the one in mach-db120.c and it works. The previous one
didn't work at all.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38094 3c298f89-4303-0410-b956-a3cf2f4a3e73
The goal is to set the WAN MAC address to the one on the
sticker on the bottom of the unit. Currently it is not
used at all. But some users expect the WAN interface to
have the MAC address that is written on the sticker.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38091 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the local MAC address parser function and use
the generic one instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38090 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the local MAC address parser function and use
the generic one instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38089 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the local MAC address parser function and use
the generic one instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38088 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the local MAC address parser function and use
the generic one instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38087 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the local MAC address parser function and use
the generic one instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38086 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rename the function and extend it in order to make it
usable from board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38085 3c298f89-4303-0410-b956-a3cf2f4a3e73
- remove common imx6q-ventana.dtsi - there isn't enough commonality to
warrent this
- rename user led's to 1-based
- add alises used by bootloader
- clean up iomux gpios
- fix pfuze slave address
- enable sata
- add delay after release of pci reset downstream from PCIe switch
- remove PCIe clock configuration as its now handled in updated driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38081 3c298f89-4303-0410-b956-a3cf2f4a3e73
It's the same as in base-files package.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38077 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change some flow-level unctions to return with an
error code in order to be able to report errors
to the core code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38068 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.
Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200
Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
- add commit message and SoB line from the original patch
- remove dead code from mach-wnr2200.c
- refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38059 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds support for Byte Queue Limits in bgmac and b44, now it is
possible to use more advanced network queue control algorithms.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38038 3c298f89-4303-0410-b956-a3cf2f4a3e73
This updates the patches for BCM5354 to the version send for upstream
Linux inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38037 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38036 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Rafał for the data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38035 3c298f89-4303-0410-b956-a3cf2f4a3e73
this will make image builder build rt305x targets per default
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38025 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is used on Huawei E970 (brcm47xx).
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38010 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds detection for Linksys E1200 V2
Thank you Lightsword and Rafał.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38006 3c298f89-4303-0410-b956-a3cf2f4a3e73
A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38005 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38004 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.
The patch is in preparation for multiple firmware format
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38002 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38001 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. Now it should be
possible to read decimal and hex vars of max 8 bit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37999 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.
However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.
This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37998 3c298f89-4303-0410-b956-a3cf2f4a3e73
Separate OpenWrt specific MTD options from the mainline
option by moving those into a new submenu in the kernel
configuration interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37997 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Use different structs depending on the number of nvram variables to check.
* Add detection of ZTE H218N, this closes#14151.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37996 3c298f89-4303-0410-b956-a3cf2f4a3e73
The revision is stored in a different register than it is in other
Broadcom switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37995 3c298f89-4303-0410-b956-a3cf2f4a3e73
These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37994 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37993 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.
Thank you Devastator for testing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37988 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the config_enabled() macro where it is possible.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37980 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37977 3c298f89-4303-0410-b956-a3cf2f4a3e73
- change patch numbers to group the related stuff together,
- add mtd prefix where it is missing,
- use hyphens in the patch names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37974 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for building firmware images for the
TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37964 3c298f89-4303-0410-b956-a3cf2f4a3e73
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37963 3c298f89-4303-0410-b956-a3cf2f4a3e73
The skb is usually started by a padding which allows the protocols in the
network stack to add their headers in front of the payload. The skb can be
reallocated in case the preallocated padding is not large enough. This can for
example happen in the function __skb_cow which will check the requested extra
headroom and allocate more buffer when the requested headroom is bigger than
the available one. The extra buffer is aligned again to the multiple of the
NET_SKB_PAD of the target architecture.
The macro used to create the multiple of the NET_SKB_PAD is written in a way
which allows only values power two as alignment parameter. The currently used
value of 48 bytes can not be written as n ** 2 but as 2 ** 4 + 2 ** 5. The
extra buffer is therefore not always the multiple of 48 but can be 16, 64, 80,
128, 144 and so on. The generated values are also not monotonic (48 requested
bytes are mapped to 80 allocated bytes and 49 requested bytes are mapped to 64
allocated bytes).
These unexpected small values result in more reallocations of the buffer. This
was noticed prominently during tests between two QCA9558 720 MHz devices which
were connected via ethernet to PCs and had a HT40 802.11n 3x3 link between each
other. The throughput PC-to-PC during iperf TCP runs increased reliable from
186 Mibit/s to 214 Mibit/s in one direction and from 195 Mibit/s to 220 Mibit/s
in the other direction. This is a performance increase of ~14% just by reducing
the amount of reallocations.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37948 3c298f89-4303-0410-b956-a3cf2f4a3e73
- enable using hwmon GSC driver on all targets
- add a kmod package for it
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37933 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently, the module causes an oops at least on rt5350. These patches
have been accepted upstream at:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37931 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is EOL since quite a while, so no need to keep it around.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37911 3c298f89-4303-0410-b956-a3cf2f4a3e73
3.10 is stable enough, and 3.9 is EOL since a while.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37910 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37906 3c298f89-4303-0410-b956-a3cf2f4a3e73
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37895 3c298f89-4303-0410-b956-a3cf2f4a3e73
The '-initramfs' string is duplicated in the image names,
fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37892 3c298f89-4303-0410-b956-a3cf2f4a3e73
Every device I connect to the USB port is detected as 2-1, not 1-1.
So adjust the default setting accordingly.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37882 3c298f89-4303-0410-b956-a3cf2f4a3e73
When the squashfs and jffs2 images are generated
in the same turn, the compressed kernel images
are generated twice with the same parameters.
Move compressed kernel generation into a separate
phase to avoid that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37881 3c298f89-4303-0410-b956-a3cf2f4a3e73
The myloader partition parser code uses ifdef wrappers
to make the code usable on kernels below version 3.2.
All targets are using kernel 3.3 at least so the wraper
is not needed. Remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37880 3c298f89-4303-0410-b956-a3cf2f4a3e73
Those are not needed since we are generating the
initramfs images along with the others.
Remove the variables and use the template names
directly.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37876 3c298f89-4303-0410-b956-a3cf2f4a3e73
Initramfs images are not generated for profiles which
are using the squashfs-only template. Add the missing
'Image/Build/Template/squashfs-only/initramfs' to fix
that.
Also, 'Image/Build/Cameo933x/initramfs' uses wrong
parameters for 'MkuImageLzma/initramfs' due to a
misplaced commma. Remove that to fix the generated
initramfs images.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37871 3c298f89-4303-0410-b956-a3cf2f4a3e73
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37869 3c298f89-4303-0410-b956-a3cf2f4a3e73
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
The current patch contains additional configuration tweaks.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37868 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add kernel configuration and patches for Linux 3.10.
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
The current patch contains additional configuration tweaks,
and the kernel patches were refreshed.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37867 3c298f89-4303-0410-b956-a3cf2f4a3e73