We do not use the result, so no need to call it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44555 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for TP-Link TL-WA7210n[0]
[0] http://www.tplink.com/en/products/details/?model=TL-WA7210N
Signed-off-by: Hendrik Frenzel <hfrenzel@scunc.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44526 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds the GMAC entries in the ipq806x dtsi file as well as in the
ap148 specific dts file.
This also adds the MDIO change as well.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44520 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change is fixing the issues observed when booting from NOR flash
with SMP enabled.
Error logs below:
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
m25p80 spi32766.0: SPI transfer failed: -110
spi_master spi32766: failed to transfer one message from queue
jffs2: Write of 873 bytes at 0x019001e8 failed. returned 0, retlen 792
Patch is cherry-picked from here:
https://www.codeaurora.org/cgit/quic/qsdk/oss/kernel/linux-msm/commit/drivers/spi/spi-qup.c?h=coconut_20140924&id=4faba89e3ffbb1c5f6232651375b9b3212b50f02
More details in the patch file.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44518 3c298f89-4303-0410-b956-a3cf2f4a3e73
It took very little to make the TL-WDR4900 work under 3.19:
- config is the same as for 3.18
- only patch 210 had to be refreshed, the other patches are
the same as for 3.18
- in /etc/config/wireless the path options need to be prefixed
with "platform/" ('platform/ffe09000.pci/...')
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44517 3c298f89-4303-0410-b956-a3cf2f4a3e73
This sets 'enable_vlan' and thus uses 802.1q
VLANs, but without tagging on either interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44509 3c298f89-4303-0410-b956-a3cf2f4a3e73
Toggles the LA bit on the WAN interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44508 3c298f89-4303-0410-b956-a3cf2f4a3e73
ipq806x target has been upgraded to 3.14. There is no need to maintain
this file anymore.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44505 3c298f89-4303-0410-b956-a3cf2f4a3e73
The watchdog driver already registers a restart notifier, we just have
to enable it in the config and in the DT to fix the "reboot" command.
This is done by integratin the following patch-set:
https://lkml.org/lkml/2015/2/20/610
I'm copy-pasting the description below:
qcom-wdt is currently assuming the presence of a dedicated node in DT
to gets its configuration. However, on msm architecture, the watchdog is
usually part of the timer block. So this patch-set is changing the driver
and slightly enhancing the timer DT bindings to provide the relevant clocks
and interrupts.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44504 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some bootloaders seem to trigger the watchdog during the boot process,
therefore the lack of watchdog driver trigger a reboot a few seconds
after boot. So we'll enable it here to avoid it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44503 3c298f89-4303-0410-b956-a3cf2f4a3e73
MPIC timers are enabled in the config, however a devicetree clock setting
is missing causing the following error:
/soc@ffe00000/timer@41100: cannot get timer frequency.
/soc@ffe00000/timer@42100: cannot get timer frequency.
This patch adds the missing clock and avoids the error.
It's a functional copy of this code
do_fixup_by_compat_u32(blob, "fsl,mpic",
"clock-frequency", get_bus_freq(0), 1);
in arch/powerpc/cpu/mpc85xx/fdt.c in the u-boot code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44501 3c298f89-4303-0410-b956-a3cf2f4a3e73
Defaulting to disabled, based on the value of
the (old?) CONFIG_RALINK_USBPHY
Signed-off-by: Claudio Leite <leitec@staticky.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44500 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thanks to Bruno Randolf for testing and Manuel Lauss for providing a fix.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44487 3c298f89-4303-0410-b956-a3cf2f4a3e73
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44486 3c298f89-4303-0410-b956-a3cf2f4a3e73
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44470 3c298f89-4303-0410-b956-a3cf2f4a3e73
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44469 3c298f89-4303-0410-b956-a3cf2f4a3e73
- according to imx6 Makefile and u-Boot documentation is itb
and probably should not be changed
- this fixes build error if CONFIG_TARGET_ROOTFS_INCLUDE_FIT is set
(missing .itb file)
- use DTS_DIR (like in imx6 Makefile)
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44468 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current pxa3xx_nand driver doesn't support sub-page writing,
so the VID header offset must be specified explicitly.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44455 3c298f89-4303-0410-b956-a3cf2f4a3e73
oops, accidently moved instead of copied them
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44454 3c298f89-4303-0410-b956-a3cf2f4a3e73
ZyXEL NBG6716 "rfkill" is a switch, not a button.
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44453 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44451 3c298f89-4303-0410-b956-a3cf2f4a3e73
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44450 3c298f89-4303-0410-b956-a3cf2f4a3e73
procd gets last console from cmdline, so swapping tty1 (framebuffer) and ttyAMA0 (uart) is enough to force procd output via uart
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44448 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Dimitri for testing this.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44430 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Allow --command-line parameters of kexec-tools be parsed and used by
the kernel.
- For malta machine, mark kernel code and kernel data segments as
"System RAM" instead of "reserved" in /proc/iomem, otherwise
kexec-tools will complain that program segments in ELF kernel file
are invalid.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44429 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds corrected profile and build image for the TL-MR12U board.
Unfortunately i cannot test the factory image since i can't find anywhere
the original chinese firmware but
the generated openwrt-ar71xx-generic-tl-mr12u-v1-squashfs-sysupgrade.bin
worked just fine over a modified mr3040 factory image i managed to modify
to initially flash the mr12u from the original firmware.
Proper kernel support probably should be added since cat /proc/cpuinfo shows
MR13U.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44427 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44426 3c298f89-4303-0410-b956-a3cf2f4a3e73
ZyXEL NBG6716 add missing GPIO USB power on/off
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44425 3c298f89-4303-0410-b956-a3cf2f4a3e73
We obviously can't use sizeof(*buf) which is always 1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44424 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add GoFlex Net "Board Name" , set and cleanup network default and LEDs.
Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44422 3c298f89-4303-0410-b956-a3cf2f4a3e73
We shouldn't read data directly into the header struct, as some devices
(e.g. Edimax) need more bytes due to some extra header.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44414 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some devices have uImage headers after some extra headers (e.g. Edimax
devices). To support such cases our verify callback function should be
allowed to return header offset, not just a boolean value.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44412 3c298f89-4303-0410-b956-a3cf2f4a3e73
usbgadget was initially enabled in the hope to support gadget mode
as it seems to be supported by the hardware.
However, it currently breaks things and doesn't work anyway, so
remove the usbgadget feature.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44407 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: michael lee <igvtee@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44401 3c298f89-4303-0410-b956-a3cf2f4a3e73
tested on a nor and a spi laguna
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44393 3c298f89-4303-0410-b956-a3cf2f4a3e73
the kernel has increased and does not fit into the 1,5MB anymore.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44391 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on config-3.18 with the following changes.
- CONFIG_GENERIC_NET_UTILS is removed as it is already set in generic
kernel config.
- CONFIG_CPU_MICROMIPS is explicitly unset as required in kernel 3.19.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44388 3c298f89-4303-0410-b956-a3cf2f4a3e73
Jonas Gorski
Felix Fietkau
Imre Kaloz
John Crispin
Rafał Miłecki
Jo-Philipp Wich
Nicolas Thill
Luka Perkov