to get and set bootloader options in flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11514 3c298f89-4303-0410-b956-a3cf2f4a3e73
to get and set bootloader options in flash memory.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11512 3c298f89-4303-0410-b956-a3cf2f4a3e73
r6040_rx() was rewritten.
Further changes:
- fix a bug in hex2str(), which overwrote the source with a zero
- removed rx_free_desc counter; allocate skb inside r6040_rx() on the fly
- r6040_rx: don't take the error from the MLSR register (may be too late) but from the descriptor (we may have to allow these errors (via MCR0) there
- r6040_alloc_rxbufs() may fail due to lack of skb, added a return value
- changed some debugs
- more defines
- version: 0.18 -> 0.19
Signed-Off by Joerg Albert <jal2@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11508 3c298f89-4303-0410-b956-a3cf2f4a3e73
- re-added the parent parameter to specify a netdevice to steal the MAC address from (optional).
- fixed null pointer access in r6040_rx() (lp->dev init. was missing)
- fixed "scheduling while atomic" endless loop if tx_timeout() was called (caused by the re-allocs of the buffers)
- fixed tx timeouts (tx irq weren't re-enabled on rx irq)
It adds some defines and cleans the code a bit (IMHO).
Signed-Off by Joerg Albert <jal2@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11507 3c298f89-4303-0410-b956-a3cf2f4a3e73
this is the first of three patches to fix the ethernet driver of RDC R32xx applied to svn r10754.
It adds debugs and make some procedures (r6040_*) global symbols in order to help with debugging kernel oops. Version is increased from 0.16 to 0.18 to avoid conflicts with the driver variant metioned in the X-WRT forum (call 0.17.3) Tested on a Sitecom WL-153.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11506 3c298f89-4303-0410-b956-a3cf2f4a3e73
I noticed my wrt350n would not reliably reboot after entering
the reboot command. I found this code in the source for the
wrt600n. It corrects the problem, and the wrt350n reboots
reliably now.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11470 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch allows the bcm57xx module to work correctly with failsafe mode.
insmod doesn't return an error when a module loads but doesn't detect a switch.
I added the check_module function to load the module, then make sure
it doesn't just exit immediately. This allows preinit to only attempt to
load the bcm57xx module when switch-robo and switch-adm dont detect a switch.
The activate_gpio parameter to bcm57xx simply instructs the module to attempt
to activate the switch via gpio before probing for the switch.
Tested on wrt350n.
Signed-off-by: Ben Pfountz <netprince (at) vt (dot) edu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@11468 3c298f89-4303-0410-b956-a3cf2f4a3e73
Imre Kaloz
Matteo Croce
John Crispin
Gabor Juhos
Andy Boyett
Felix Fietkau
Yuji Mano
Peter Denison
Florian Fainelli