This patch adds support for the Omnima MiniPlug RT5350 based board, 8MB SPI flash
Signed-off-by: Ivan Ignjatic<ivan@omnima.co.uk>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42200 3c298f89-4303-0410-b956-a3cf2f4a3e73
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42194 3c298f89-4303-0410-b956-a3cf2f4a3e73
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42193 3c298f89-4303-0410-b956-a3cf2f4a3e73
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42184 3c298f89-4303-0410-b956-a3cf2f4a3e73
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42180 3c298f89-4303-0410-b956-a3cf2f4a3e73
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42179 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the pcb tracing results[1] by anton.rad[2] MPR-A1s expose
6 unused GPIOs, only one of them working as configured in the current
DTS. This patch enables GPIO22-26.
Tested on hardware.
[1] http://i.imgur.com/kHVW2Ox.jpg
[2] https://forum.openwrt.org/viewtopic.php?pid=222698#p222698
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42178 3c298f89-4303-0410-b956-a3cf2f4a3e73
The conversion was not 100% correct and leads to u-boot failing to
verify the CRC, revert that change for now.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42170 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is causing more harm than good on most AR7 routers out there,
better have no manageable switch rather than no ethernet connection, at
least for now.
Fixes#16523, #5927
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42168 3c298f89-4303-0410-b956-a3cf2f4a3e73
we should check for ssb here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42164 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GW5520 is a small form-factor single-board computer with the following
features:
* 70x100mm form-factor
* IMX6DL 800MHz SoC (IMX6Q optional)
* 512MB 32bit DDR3 SDRAM (up to 2GB optional)
* 256MB NAND FLASH (up to 2GB optional)
* Gateworks System Controller
* 2x front-panel Intel i210 GbE adapters with passive PoE support
* 2x MiniPCIe sockets with USB support
* 2x front-panel USB
* 1x rear-panel full-size HDMI connector
* 1x front-panel bi-color user LED
* 1x front-panel user pushbutton
* 1x rear-panel barrel jack for power
* 1x Application connector with:
* 2x TTL level UARTs
* 10x TTL level Digital IO
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42148 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
* 7-port Ethernet Switch
* 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
* 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)
This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42147 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GW16082 miniPCI Expansion Mezzanine has the INTA/B/C/D IRQ's reversed
from the PCI standard. This will soon be resolved in the bootloader via
devicetree, but in the meantime this will work around the issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42146 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now it is possible to use b43 wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42143 3c298f89-4303-0410-b956-a3cf2f4a3e73
bcma does not support this card and b43 hangs when probing this card.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42142 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42129 3c298f89-4303-0410-b956-a3cf2f4a3e73
This splits up neufbox 4 for now into two images, one for each OEM.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42128 3c298f89-4303-0410-b956-a3cf2f4a3e73
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42126 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use appended dtb for board detection for bcm96328avng.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42124 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the required nodes to the dtsi files and code to prevent double
registration from the board support code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42123 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a helper for building images with dtb appended kernels.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42122 3c298f89-4303-0410-b956-a3cf2f4a3e73
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42121 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42119 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make it less likely for quilt/patch to put boards into the "wrong"
section.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42117 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hauke Mehrtens
John Crispin
Florian Fainelli
Luka Perkov
Imre Kaloz
Jonas Gorski
