Update the xburst target to kernel version 3.18 and also remove the broken 3.10 support.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45031 3c298f89-4303-0410-b956-a3cf2f4a3e73
will re-add it tomorrow after fixing it
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45028 3c298f89-4303-0410-b956-a3cf2f4a3e73
The usb stroage not working since updated 3.18. Porting from MTK's source code.
Signed-off-by: wengbj <fl.service@t-firefly.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45021 3c298f89-4303-0410-b956-a3cf2f4a3e73
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Last time i got some mess . This is new version.
Signed-off-by: Jay Weng <fl.service@t-firefly.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45018 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use `mktplinkfw sysupgrade` or `mktplinkfw factory` or
`mktplinkfw image`
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44998 3c298f89-4303-0410-b956-a3cf2f4a3e73
Should fix pcmcia on BCM6348 and BCM6358 after switching to DT-probed
gpio controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44995 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes the following issue:
drivers/gpio/gpio-bcm63xx.c: In function 'bcm63xx_gpio_probe':
drivers/gpio/gpio-bcm63xx.c:80:4: error: implicit declaration of function 'devm_kasprintf' [-Werror=implicit-function-declaration]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44986 3c298f89-4303-0410-b956-a3cf2f4a3e73
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44985 3c298f89-4303-0410-b956-a3cf2f4a3e73
Respect the vmlinux load address when generating images.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44983 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44982 3c298f89-4303-0410-b956-a3cf2f4a3e73
All images generated contain dtbs, so it is now unused.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44980 3c298f89-4303-0410-b956-a3cf2f4a3e73
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44969 3c298f89-4303-0410-b956-a3cf2f4a3e73
Zoltan HERPAI
Felix Fietkau
Lars-Peter Clausen
John Crispin
Imre Kaloz
Jonas Gorski
Gabor Juhos
Rafał Miłecki