Thanks to Bruno Randolf for testing and Manuel Lauss for providing a fix.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44487 3c298f89-4303-0410-b956-a3cf2f4a3e73
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44486 3c298f89-4303-0410-b956-a3cf2f4a3e73
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44470 3c298f89-4303-0410-b956-a3cf2f4a3e73
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44469 3c298f89-4303-0410-b956-a3cf2f4a3e73
- according to imx6 Makefile and u-Boot documentation is itb
and probably should not be changed
- this fixes build error if CONFIG_TARGET_ROOTFS_INCLUDE_FIT is set
(missing .itb file)
- use DTS_DIR (like in imx6 Makefile)
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44468 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current pxa3xx_nand driver doesn't support sub-page writing,
so the VID header offset must be specified explicitly.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44455 3c298f89-4303-0410-b956-a3cf2f4a3e73
oops, accidently moved instead of copied them
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44454 3c298f89-4303-0410-b956-a3cf2f4a3e73
ZyXEL NBG6716 "rfkill" is a switch, not a button.
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44453 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44451 3c298f89-4303-0410-b956-a3cf2f4a3e73
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44450 3c298f89-4303-0410-b956-a3cf2f4a3e73
procd gets last console from cmdline, so swapping tty1 (framebuffer) and ttyAMA0 (uart) is enough to force procd output via uart
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44448 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Dimitri for testing this.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44430 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Allow --command-line parameters of kexec-tools be parsed and used by
the kernel.
- For malta machine, mark kernel code and kernel data segments as
"System RAM" instead of "reserved" in /proc/iomem, otherwise
kexec-tools will complain that program segments in ELF kernel file
are invalid.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44429 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds corrected profile and build image for the TL-MR12U board.
Unfortunately i cannot test the factory image since i can't find anywhere
the original chinese firmware but
the generated openwrt-ar71xx-generic-tl-mr12u-v1-squashfs-sysupgrade.bin
worked just fine over a modified mr3040 factory image i managed to modify
to initially flash the mr12u from the original firmware.
Proper kernel support probably should be added since cat /proc/cpuinfo shows
MR13U.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44427 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44426 3c298f89-4303-0410-b956-a3cf2f4a3e73
ZyXEL NBG6716 add missing GPIO USB power on/off
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44425 3c298f89-4303-0410-b956-a3cf2f4a3e73
We obviously can't use sizeof(*buf) which is always 1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44424 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add GoFlex Net "Board Name" , set and cleanup network default and LEDs.
Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44422 3c298f89-4303-0410-b956-a3cf2f4a3e73
We shouldn't read data directly into the header struct, as some devices
(e.g. Edimax) need more bytes due to some extra header.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44414 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Jo-Philipp Wich
Rafał Miłecki
Imre Kaloz
Nicolas Thill
Luka Perkov