This deactivates ssb and G-PHY code in b43 for the mips74k profile in
brcm47xx.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41594 3c298f89-4303-0410-b956-a3cf2f4a3e73
Reduces code size a bit and sets affinity to boot cpu by default.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41591 3c298f89-4303-0410-b956-a3cf2f4a3e73
Restore alphatetical order in uci-defaults scripts and brcm63xx.sh
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41590 3c298f89-4303-0410-b956-a3cf2f4a3e73
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41588 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch also makes use of the new leds script.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41585 3c298f89-4303-0410-b956-a3cf2f4a3e73
By using uci-defaults force_link is enabled, which fixes some link issues if ethernet cable isn't connected when LAN is initialized.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41583 3c298f89-4303-0410-b956-a3cf2f4a3e73
this will make the rc1 images boot with the default config.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41578 3c298f89-4303-0410-b956-a3cf2f4a3e73
found 2 more
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41574 3c298f89-4303-0410-b956-a3cf2f4a3e73
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.
This was the one thing missing from r41474 for sysupgrade board
detection to work properly.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41567 3c298f89-4303-0410-b956-a3cf2f4a3e73
Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.
I'll leave the equivalent patch for xrx200 to someone who has a
board to test.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41565 3c298f89-4303-0410-b956-a3cf2f4a3e73
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.
Signed-off-by: André Valentin <avalentin@marcant.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41562 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since kernel 3.11, the third parameter passed to notifier_call()
is of type struct netdev_notifier_info. This patch fixes an oops
when setting a netdev LED trigger.
Signed-off-by: Claudio Leite <leitec@staticky.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41552 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move defines and board_info structs back to their proper locations so
(de-)selecting SOC support won't break the build.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41550 3c298f89-4303-0410-b956-a3cf2f4a3e73
A reboot is issued by setting the watchdog timer to a low value, when
the value is decreased from 1 to 0 by the hardware the system will
reboot. Setting this value to 1 does not work every time, it is a
little bit more reliable when setting it to 3. This timer runs with
some MHz or KHz so nobody will notice the increased waiting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41548 3c298f89-4303-0410-b956-a3cf2f4a3e73
broadcom-wl now builds in the mips74k profile, so remove these chips
from the generic profile.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41546 3c298f89-4303-0410-b956-a3cf2f4a3e73
The previous attempt (r40717) to fix squashfx made the system bootable but
overlayfs remained broken.
This enables block2mtd again using the right partition number and naming
and adds MTD_ROOTFS_SPLIT option.
However onboard rootfs partition name had to be renamed to place overlay on
CF instead of onboard NAND.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41541 3c298f89-4303-0410-b956-a3cf2f4a3e73
No config option should be set to m in the default config, because
there is also some script needed which picks the module up into the
image and that is missing this way. Always create a kmod when building
a module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41539 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41538 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41537 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41534 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most ar7 devices have only 16 MiB RAM, so select low_mem to give them
a chance to work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41532 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41531 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Hauke Mehrtens
Jonas Gorski
Luka Perkov
Felix Fietkau
Imre Kaloz