The 3.6 kernel isn't used by any of the x86 subtargets, so remove it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39403 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39402 3c298f89-4303-0410-b956-a3cf2f4a3e73
This ensures that the generated images will have enough erase
blocks for JFFS2.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39397 3c298f89-4303-0410-b956-a3cf2f4a3e73
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39392 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used for Compex devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39388 3c298f89-4303-0410-b956-a3cf2f4a3e73
Recent lxc versions are not useful if this option is not enabled. That said,
enable KERNEL_POSIX_MQUEUE by default when KERNEL_LXC_MISC is selected.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39385 3c298f89-4303-0410-b956-a3cf2f4a3e73
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39384 3c298f89-4303-0410-b956-a3cf2f4a3e73
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.
Fix the macro to check the size of the final image
instead of the rootfs image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39383 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39382 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39379 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39378 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39373 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make the IPv4 "do not fragment" bit a configurable variable for the 6rd
tunnel interface as the bit should not be set in the encapsulating IPv4
header according to RFC3056.
On top the config variable allows to enable/disable path mtu discovery
for tunnel interfaces.
Config variable can be passed to netifd as tunnel config support is
already present for the "do not fragment" bit.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39370 3c298f89-4303-0410-b956-a3cf2f4a3e73
The default inittab uses "askconsole" which is implemented by procd
and uses the console provided by the kernel command line.
Hence, this platform specific workaround is not necessary anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39367 3c298f89-4303-0410-b956-a3cf2f4a3e73
make sure log buffer size is not bigger than the ubus message size
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39365 3c298f89-4303-0410-b956-a3cf2f4a3e73
Support for the BCM63268 is usable, enable it by default.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39364 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add kernel support for the BCM963269BHR board, USB and Ethernet switch,
LEDs and buttons are working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39363 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow using the HSSPI controller since it works just fine, as well as
the integrated switch core, since that one works too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39362 3c298f89-4303-0410-b956-a3cf2f4a3e73
The HIFN driver is a PCI driver, thus requires PCI support to be enabled
to compile. Therefore let it depend on PCI..
Should fix mvebu builds.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39357 3c298f89-4303-0410-b956-a3cf2f4a3e73
we should not abuse the platform_data pointer.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39354 3c298f89-4303-0410-b956-a3cf2f4a3e73
Florian Fainelli
Gabor Juhos
Luka Perkov
Steven Barth
John Crispin
Zoltan HERPAI
Jonas Gorski
Hauke Mehrtens