This patch adds OpenWRT support for the Netgear WNR2200 (N300)
wireless router with USB.
Technical details of this router can be found at
http://www.netgear.com/home/products/wirelessrouters/work-and-play/WNR2200.aspx
and http://wikidevi.com/wiki/Netgear_WNR2200
Signed-off-by: Aidan Kissane <aidankissane@googlemail.com>
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4055/
[juhosg:
- add commit message and SoB line from the original patch
- remove dead code from mach-wnr2200.c
- refresh 624-MIPS-ath79-WNR2200-support.patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38059 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds support for Byte Queue Limits in bgmac and b44, now it is
possible to use more advanced network queue control algorithms.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38038 3c298f89-4303-0410-b956-a3cf2f4a3e73
This updates the patches for BCM5354 to the version send for upstream
Linux inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38037 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38036 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Rafał for the data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38035 3c298f89-4303-0410-b956-a3cf2f4a3e73
this will make image builder build rt305x targets per default
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38025 3c298f89-4303-0410-b956-a3cf2f4a3e73
now that we have modprobe we can set more than half of the modules to AutoProbe
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38021 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is needed to make modprobe work
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38020 3c298f89-4303-0410-b956-a3cf2f4a3e73
ubox now has modprobe support
build and install the tool
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38019 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is used on Huawei E970 (brcm47xx).
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38010 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Javier Achirica for the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38008 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds detection for Linksys E1200 V2
Thank you Lightsword and Rafał.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38006 3c298f89-4303-0410-b956-a3cf2f4a3e73
Gabor Juhos
Felix Fietkau
John Crispin
Luka Perkov
Hauke Mehrtens
Steven Barth