The 3.10.x infrastructure has been present for some time, and seems to
run fine here.
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39483 3c298f89-4303-0410-b956-a3cf2f4a3e73
It was recently sent to linux-mips for comments. It adds workaround for
WNR3500L to enable USB port.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39469 3c298f89-4303-0410-b956-a3cf2f4a3e73
It does the same, it just reorders things
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39468 3c298f89-4303-0410-b956-a3cf2f4a3e73
This does not add any new features, just some changes to the patches
and a first try to use dt to set the irqs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39466 3c298f89-4303-0410-b956-a3cf2f4a3e73
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.
[juhosg: change subject]
Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39429 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since the yaffs code update (r39084), it is not
possible to install OpenWrt on RouterBoards with
small-page NAND chips. Fix the yaffs code to make
it work again.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39409 3c298f89-4303-0410-b956-a3cf2f4a3e73
The 3.6 kernel isn't used by any of the x86 subtargets, so remove it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39403 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the 'swconfig_trig_set_brightness' function to set
the brightness value of the LED when the link goes down.
This ensures that the last brighness value is saved into
a local variable which is used to track the actual LED
status.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39402 3c298f89-4303-0410-b956-a3cf2f4a3e73
This ensures that the generated images will have enough erase
blocks for JFFS2.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39397 3c298f89-4303-0410-b956-a3cf2f4a3e73
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39392 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used for Compex devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39388 3c298f89-4303-0410-b956-a3cf2f4a3e73
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39384 3c298f89-4303-0410-b956-a3cf2f4a3e73
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.
Fix the macro to check the size of the final image
instead of the rootfs image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39383 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reverts r38197.
The automatically created firmware partition includes
the partition_table partition. Apart from the partition
table, this partition contains sensitive data on some
Compex devices which data can be destroyed when the
firmware partition gets modified. Revert the change to
prevent that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39382 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39379 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39378 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39373 3c298f89-4303-0410-b956-a3cf2f4a3e73
The default inittab uses "askconsole" which is implemented by procd
and uses the console provided by the kernel command line.
Hence, this platform specific workaround is not necessary anymore.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39367 3c298f89-4303-0410-b956-a3cf2f4a3e73
Support for the BCM63268 is usable, enable it by default.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39364 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add kernel support for the BCM963269BHR board, USB and Ethernet switch,
LEDs and buttons are working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39363 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow using the HSSPI controller since it works just fine, as well as
the integrated switch core, since that one works too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39362 3c298f89-4303-0410-b956-a3cf2f4a3e73
The HIFN driver is a PCI driver, thus requires PCI support to be enabled
to compile. Therefore let it depend on PCI..
Should fix mvebu builds.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39357 3c298f89-4303-0410-b956-a3cf2f4a3e73
we should not abuse the platform_data pointer.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39354 3c298f89-4303-0410-b956-a3cf2f4a3e73
- as ENT_DEBUG is removed, move the messages into pr_notice
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39350 3c298f89-4303-0410-b956-a3cf2f4a3e73
Replace the leading spaces with tabs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39342 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used for AR8327.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39337 3c298f89-4303-0410-b956-a3cf2f4a3e73
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39335 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update a few devices with their actual port numbers, especially those
with two ports.
Should allow properly using the second port on the Neufboxen and HW553
and HW556.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39325 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow setting the number of available usb host ports for boards with
additional sanity checks to allow using the second port on devices
where it is available.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39324 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add and enable USB support for the BCM63268 family of SoCs.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39323 3c298f89-4303-0410-b956-a3cf2f4a3e73
USB will fail to work if compiling with BCM6318 only if BCM63XX_HAS_EHCI
and BCM63XX_HAS_OHCI are not selected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39322 3c298f89-4303-0410-b956-a3cf2f4a3e73
Return the same clock for usbh and usbd on BCM6318 to prevent the clock
getting disabled despite being supposed to be enabled, e.g. by the
following sequence:
clk_enable(usbh); <- usbh->usage = 1, enabled
clk_enable(usbd); <- usbd->usage = 1, enabled (no effect)
clk_disable(usbd); <- usbd->usage = 0, -> disabled!
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39321 3c298f89-4303-0410-b956-a3cf2f4a3e73
Changeset r39302 updated a board section and added twice .has_ehci0,
this is not necessary, so fix it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39304 3c298f89-4303-0410-b956-a3cf2f4a3e73
This board is pretty similar to ARV752DPW22.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39303 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM6318 has a special initialization sequence which involves touching
PLL control registers in the USBH_PRIV register space, as well as
toggling a bit the Simulation control register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39302 3c298f89-4303-0410-b956-a3cf2f4a3e73
The rt2x00 wifi driver may still need updating to
function with this device.
Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39298 3c298f89-4303-0410-b956-a3cf2f4a3e73
Power LED is not active low, and ppp-fail is red, not green.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39294 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was not supposed to be committed, remove it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39293 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable the use of the USB gadget device at the board level so we can use
bcm63xx_udc on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39292 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also fixing a build warning due to a misplaced parenthesis in the
previous submission.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39291 3c298f89-4303-0410-b956-a3cf2f4a3e73
Very similar to the BCM96318REF board except for the name and the
SDRAM/DDR configuration which is totally transparent for us.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39286 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM6318 support is usable enough to be enabled by default, turn it on.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39284 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add basic support for the BCM96318REF board which is comprised of:
- HS-SPI flash support
- Ethernet switch support
- USB slave device support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39283 3c298f89-4303-0410-b956-a3cf2f4a3e73
Provide clock toggling for the USB host and slave controller as well as
for the Ethernet Switch. The bcm63xx_enetsw driver is changed not to use
request_mem_region() as the Roboswitch register overlaps with the
Roboswitch IUDMA channels, hence making the driver return -EBUSY. A
future fix might be to use variable size RSET_ENETSW sizes depending on
the chip we are targetting.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39282 3c298f89-4303-0410-b956-a3cf2f4a3e73
While adding support for BCM6345 Ethernet, some changes in the macros
ENETDMA{C,S} where introduced which now make the bcm63xx USB gadget
driver fail to build. Fix this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39279 3c298f89-4303-0410-b956-a3cf2f4a3e73
A missing condition check in dev-hsspi.c prevented the controller from
being registered on 6318 where it is fully functional.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39278 3c298f89-4303-0410-b956-a3cf2f4a3e73
varid might both unused and unitialized when building for e.g: bcm6318,
fix these two warnings turned into errors.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39277 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM63XX's ohci controller does not need the frame number shift, but that
was guarded with a PPC symbol. Fix this by making the no-fix generally
available.
This is a regression from the previous conversion to ohci platform driver.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39274 3c298f89-4303-0410-b956-a3cf2f4a3e73
CFE seems to leave the SPI flash mapping in an invalid state after
loading the kernel on some reference boards, so fix it up on boot.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39273 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add inital support for BCM6318, but keep it disabled for now until
most things are supported.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39272 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add initial support for the BCM63268 family of SoCs, but keep it
disabled for now as most things don't work yet.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39271 3c298f89-4303-0410-b956-a3cf2f4a3e73
The low PCIe window on BCM6328 and BCM6362 is actually only 1 MiB big,
not 16 MiB.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39270 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some SoCs have variants which are mostly the same, but use a different
chip id (or not). Add code for detecting them and handling them as
their standard counterparts.
This adds support for e.g. BCM6369.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39269 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the non runtime detect code since its effectiveness is dubious
and almost never used.
Also update affinity patches to work on top of it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39268 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update bmips cleanup patches with upstream submission and backport a few
bmips fixes.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39267 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes generic SPI flash accesses on BCM6358/BCM6368. BCM6338 still needs
additional fixes for M25P80, so it remains broken for now.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39266 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes e.g. SPI flash access on BCM6358/BCM6368. Transfers < 256 bytes
are not affected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39265 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the HSSPI driver with the upstream submitted one that has a
workaround for the auto cs down issue.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39264 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are no generic patches for kernel 3.7 any more, remove this stuff.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39262 3c298f89-4303-0410-b956-a3cf2f4a3e73
Instead of looking into the proc entry provided by broadcom-diag use
the board info from /proc/cpuinfo to get the board we are on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39256 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the new led api also on brcm47xx.
The led for failsafe indication is searched for.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39255 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove the code used on the old switch driver.
The Ethernet drive is loaded as a module and needs some time to get up
therefor we added some wait function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39254 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes brcm47xx target use the default gpio led and button driver
and not broadcom-diag any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39253 3c298f89-4303-0410-b956-a3cf2f4a3e73
This backports some patches from linux upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39249 3c298f89-4303-0410-b956-a3cf2f4a3e73
This helps to avoid high order alloction failures.
Closes#14702.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39247 3c298f89-4303-0410-b956-a3cf2f4a3e73
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is
severely lacking. This patch brings it up-to-date.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39230 3c298f89-4303-0410-b956-a3cf2f4a3e73
- let LBDAF be set by generic config
- add high-speed timer support
- refresh sun5i USB patch
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39223 3c298f89-4303-0410-b956-a3cf2f4a3e73
The r39147 commit introduces a regression: at lease on some routers
with ar8216 switch large packets get lost if 802.1q tagged port is
used on the interface connected to the aforementioned switch.
The r39147 changes code in the way so interface is set to accept
packets no longer than max ethernet frame length for a given mtu.
Unfortunately ar8216 has a feature: it sends two additional bytes
as a packet header and those this header needs to be added to the
max frame length. Otherwise long enough packets get lost.
The problem only manuifests itself if interface is used in vlan
tagged mode. If interface is untagged then ar8216's header fits
into space used by 802.1q tag and not packets are lost.
Include two additional bytes in the max frame length calculation
to fix the issue.
This patch is tested and works with Trendnet TEW-632BRP.
Signed-off-by Nikolay Martynov <mar.kolya@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4656/
[juhosg:
- simplify the patch to include the additional bytes of the
switch header unconditionally,
- change subject and update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39219 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39217 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39216 3c298f89-4303-0410-b956-a3cf2f4a3e73
The built-in wireless MAC of the AR934x SoC can handle
external LNAs and the control signal of the LNAs can be
routed to any GPIO line. Add a helper function which
can be used to configure the GPIO lines.
The helper function will be used for AR934x boards
which are using externel LNAs to improve sensitivity.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39215 3c298f89-4303-0410-b956-a3cf2f4a3e73
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39214 3c298f89-4303-0410-b956-a3cf2f4a3e73
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39213 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the DMA problems with the Ethernet driver.
This also updates some other parts of the patches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39203 3c298f89-4303-0410-b956-a3cf2f4a3e73
The PHY always says there is no link
Instead of doing this dma sync a mdelay does the same trick and it is as unreliable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39202 3c298f89-4303-0410-b956-a3cf2f4a3e73
hexdump is already added to new temporary file system while less is not used at
all. While at it, remove some trailing whitespaces.
Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39181 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was called to early.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39167 3c298f89-4303-0410-b956-a3cf2f4a3e73
This uses a fixed phy instead of a dummy one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39166 3c298f89-4303-0410-b956-a3cf2f4a3e73
This updates the bgmac backport patch to the current upstream version
and adds some more patches mostly for BCM4707.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39165 3c298f89-4303-0410-b956-a3cf2f4a3e73
added dts file and userspace scripts modified to support Asus RT-N14U board
current support status:
usb works
ethernet works
buttons reset, wps
leds asus:blue:[usb|lan|wan|air|power]
i2c not tested
uart not tested
wifi not yet
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39163 3c298f89-4303-0410-b956-a3cf2f4a3e73
describes register set to control last gpio pin on mt7620 platfrom
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39162 3c298f89-4303-0410-b956-a3cf2f4a3e73
It makes no sense, the SoC has no built-in switch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39160 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39149 3c298f89-4303-0410-b956-a3cf2f4a3e73
The currently used bitmask of the maximum frame length field
is wrong for both models. On AR724x/AR933x the largest frame
size is 2047 bytes, on the AR934x it is 16383 bytes.
Make the MTU setup code model specific, and use the correct
bitmask for both models. Also change the value to the maximum.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39148 3c298f89-4303-0410-b956-a3cf2f4a3e73
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init()
and write the correct value into that from the ag71xx_open()
and ag71xx_fast_reset() functions.
Also recalculate the RX buffer size based on the actual
maximum frame length value to optimize memory allocation.
Additionaly, disallow to change the MTU value while the
interface it running.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39147 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will allow to use SoC specific values for both.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39145 3c298f89-4303-0410-b956-a3cf2f4a3e73
The currently used bitmask is not correct for all SoCs.
Introduce a new field in struct ag71xx and store the
bitmask in that. Use the current value for now, it will
be adjusted for each SoCs in further patches.
Aslo use the new field directly in the ag71xx_rx_packets
and ag71xx_hard_start_xmit() functions and remove the
ag71xx_desc_pktlen() helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39144 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without it in some occasions oops is shown on network restart. Problem was
noticed on imx6 targed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39134 3c298f89-4303-0410-b956-a3cf2f4a3e73
The previous patch was not the proper fix for PCI devices that require io
resources. The new patch is the proper fix backported from mainline.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39133 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that the switch works correctly we can enable the images for this
board.
Flashing from the factory firmware, the factory failsafe loader and
sysupgrade was tested successfully.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4617/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39130 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39129 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39128 3c298f89-4303-0410-b956-a3cf2f4a3e73
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39127 3c298f89-4303-0410-b956-a3cf2f4a3e73
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39126 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently, the AG71XX_RX_PKT_SIZE value limits the received
frame size to 1514/1516 bytes with/without a VLAN header
respectively. However the hardware limit is controlled by
the value the AG71XX_REG_MAC_MFL register which contains
the value of the max_frame_len field.
Compute the RX buffer size from the max_frame_len field
to get rid of the 1514/1516 byte limitation. Also remove
the unused AG71XX_RX_PKT_SIZE definition.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39121 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows to change the value dynamically.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39120 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will allow to use different values for the
different SoCs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39117 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ar7240_probe function uses the network device name
in the kernel log messages, however the name is not yet
initialized when the ar7240_probe function is called.
Use the mdio bus name in the messages to avoid ugly
log lines like the following one:
eth%d: Found an AR7240/AR9330 built-in switch
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39116 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ag71xx debugfs code uses the network device name
for the device specific debugfs directory. Since r38689
'ar71xx: ag71xx: fix a race involving netdev registration'
the debugfs initialization happens before the ethernet
device gets registered and the network device name contains
'eth%d' at this point. If the board setup code registers
multiple ag71xx devices, the debugfs code tries to create
the device specific dir with the same name which causes
an error like this:
eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
ag71xx: probe of ag71xx.0 failed with error -12
Use the device name for the debugfs directory to avoid the
collisions. Also add an error message and change the return
code if the debugfs_create_dir call fails.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39115 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some of the Gateworks Ventana boards have CAN bus support, therefore
we will install the userspace utils.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39113 3c298f89-4303-0410-b956-a3cf2f4a3e73
All Gateworks Ventana boards have a Gateworks System Controller
which emulates the following:
- ds1672 RTC
- pca953x GPIO expander
- hardware monitor
- at24 eeprom
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39112 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39102 3c298f89-4303-0410-b956-a3cf2f4a3e73
Set up the chipselect GPIO directly in rb95x_nand_init
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39087 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is used on newer RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39086 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit bc76682d93955cfb33051beb503ad9f8a5450578
Merge: 3a8580e ffa781d
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Jul 11 17:46:25 2013 +1200
Merge branch 'master' of ssh://www.aleph1.co.uk/home/aleph1/git/yaffs2
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39084 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39083 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39082 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is not used by any platform.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39081 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: remove the image generation part until the ethernet
switch issue is resolved]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39078 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39077 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables jumbo frames on AR8327 switch by default.
I have tested it on TP-Link TL-WDR3600.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39076 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TL-WA801ND v2 board has only one LAN port which makes
it more similar to the TL-WR[78]50RE devices. Move the
board setup code into the mach-tl-wax50re.c file.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39072 3c298f89-4303-0410-b956-a3cf2f4a3e73
This way it is a bit easier to add other TP-LINK devices based on the
Atheros AP123 reference board with one LAN port.
Based-on: http://patchwork.openwrt.org/patch/4506/
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39071 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add the user space support for the TL-WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4501/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39064 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add kernel support for the TP-LINK WA801ND v2
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Patchwork: http://patchwork.openwrt.org/patch/4500/
[juhosg:
- the TL-WA801ND v2 does not have a sliding switch, it uses a push button
for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that,
- rename kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39063 3c298f89-4303-0410-b956-a3cf2f4a3e73
This breaks some devices where the serial console is not at port 0 but
somewhere else.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39060 3c298f89-4303-0410-b956-a3cf2f4a3e73
there are still various missing pieces for full support.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39040 3c298f89-4303-0410-b956-a3cf2f4a3e73
GW5400, GW5300, and GW5200 have CAN bus option.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39034 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Gateworks GW53xx family of products is based on the Freescale
i.MX6DL SoC and offers a small form-factor with peripherals such as:
* i.MX6DL
* NAND FLASH
* 4x PCIe
* 4x USB EHCI (1x front-panel; 3x PCIe sockets)
* 1x USB OTG
* 1x uSD
* LVDS connector (VLDS for display, PWM/GPIO for backlight, i2c for touch)
* HDMI Audio/Video out
* Analog Video in
* Digital IO
* Gateworks System Controller
* Accelerometer
* Canbus
* Optional GPS
* Industrial temp (-40C to +85C)
* DC input voltage 8 to 42V (Passive PoE and 802.3af)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39012 3c298f89-4303-0410-b956-a3cf2f4a3e73
DMA and SDMA support are needed for ssi based audio. Note that the sdma
firmware is no longer required for ssi audio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39011 3c298f89-4303-0410-b956-a3cf2f4a3e73
Linaro GCC 4.6-2013.05 incorrectly pads the arpt_arp structure on
at least the ar71xx target, resulting in a two bytes shorter struct
in the kernel compared to what arptables userspace expects.
When comparing sizeof(struct arpt_arp) in kernel and userspace, the
former yields 162 byte, while the latter is 164 byte.
As a consequence, the subsequent target_offset and next_offset
members of the parent arpt_entry structure contain invalid values
when processed by the arptables binary, leading to bad memory
accesses in the populate_cache() procedure, subsequently causing a
segfault.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38999 3c298f89-4303-0410-b956-a3cf2f4a3e73
The wait instruction is only broken on the BCM4706 and not on the other
similar SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38979 3c298f89-4303-0410-b956-a3cf2f4a3e73
This sets both values to the OpenWrt default values. There is no reason
to use some brcm47xx specific values here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38978 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds support for vectored interrupts in this SoC.
This is supported by the 74K cpus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38975 3c298f89-4303-0410-b956-a3cf2f4a3e73
bcm47xx misses cpu overwrites for the features of the CPUs used in
these SoCs.
Instead of manually checking, it is now known at compile time for some
options and the compiler is able to remove the checks and optimize the
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38974 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:
commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sat Apr 6 22:22:26 2013 +0000
brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.
This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38973 3c298f89-4303-0410-b956-a3cf2f4a3e73
That function provides a slightly improved sanity check than the
currently used solution.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38967 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables the convenient sysupgrade feature for
WD's Wi-Fi Range Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4341/
[juhosg:
- rename 'mynet_rext_check_image' function to 'cybertan_check_image'
and move that into platform.sh,
- remove the the model specific 'platform_do_upgrade_mynet_rext' function,
- drop the mynet-rext.sh script,
- remove the image/Makefile change,
- update commit message]
[christian:
- check all 8 bytes of the firmware/device magic]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38966 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make the Image/Build/CyberTAN macro more generic,
and use simple wrappers for the GZIP/LZMA variants.
This simplifies the Makefile a bit, and allows to
build sysupgrade images for the devices which are
using LZMA compressed uImages.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38965 3c298f89-4303-0410-b956-a3cf2f4a3e73
In the current sysupgrade images, the CRC32 value of
the TRX header covers the whole rootfs data. Due to
this, the CRC value should be changed during sysupgrade
otherwise the bootloader refuses to load the image on
the next boot.
Change the image generation to create sysupgrade images
where the CRC32 value covers the kernel data only. This
allows to skip the 'fixtrx' step during sysupgrade on
the target.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38964 3c298f89-4303-0410-b956-a3cf2f4a3e73
Argus ATP52B: ethernet didn't work because of unconfigured switch
Sparklan WCR150GN: add switch config and make single port to be LAN
Dlink DIR-645: seems to be a redundant case
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38960 3c298f89-4303-0410-b956-a3cf2f4a3e73
There was no way to determine a working config, because
the switch (ar8337) was not working previously.
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4470/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38953 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is needed to use the switch inside the Sitecom WLR-8100;
it was unusable and detected as Generic-Phy before.
since ar8337 is behaving like ar8327
generally do the same thing
see: https://forum.openwrt.org/viewtopic.php?pid=214218#p214218
forward-ported to trunk
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Patchwork: http://patchwork.openwrt.org/patch/4469/
[juhosg: merge chip_is_ar83[23]7 statements in ar8xxx_phy_config_init]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38952 3c298f89-4303-0410-b956-a3cf2f4a3e73
The device has three extra LEDs which indicate the quality
of the wireless link. Thanks to rssileds, this feature now
works out of the box.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4462/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38950 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch improves support for the device considerably.
1. The wifi didn't work in the initial release. This was because
the WMAC of the AR9340 is not connected to the antennas.
(However, it can pick up wifi signals, if they are strong enough!)
Instead there's a dedicated AR9300 chip on the same board, which
works.
2. Ethernet throughput is improved. iperf shows that the hardware
can sustain more than 200Mbit/s and no longer drops any packages
when the link is under load.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4461/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38949 3c298f89-4303-0410-b956-a3cf2f4a3e73
The F1E Phy (AR8035?) requires additional bits to be
set in order to provide a fast and reliable connection
over gigabit links.
When enabled, the link doesn't suffer anymore from a small
package loss under load and the performance is improved
quite a bit as well. (203 mbit/s vs 112 mbit/s, iperf tcp).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Patchwork: http://patchwork.openwrt.org/patch/4460/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38948 3c298f89-4303-0410-b956-a3cf2f4a3e73
Small update to uci_defaults/01_leds, to support the usb led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4426/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38947 3c298f89-4303-0410-b956-a3cf2f4a3e73
Just a small oversight my part, added the support for the USB led
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4425/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38946 3c298f89-4303-0410-b956-a3cf2f4a3e73
Several users reported that they would like this feature.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38901 3c298f89-4303-0410-b956-a3cf2f4a3e73
The '-U' aka '--squash-uids' is already used in Image/mkfs/ubifs function.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38898 3c298f89-4303-0410-b956-a3cf2f4a3e73
this was caused by not honoured error return codes of of_gpio_count()
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38878 3c298f89-4303-0410-b956-a3cf2f4a3e73
- change uImage creation to use zImage
- update image Makefile for further boards with u-boot support
- add profile for OLinuXino Micro/Nano boards
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38876 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch fixes the NAPI poll mechanism in the GIANFAR ethernet driver, which
was not properly working since Linus Kernel Version 3,8.
Therefore the workaround patch to downgrade the GIANFAR ethernet driver to
Kernelversion v3.8 is obsoete.
This patch was extensivly testes with different network loads and types of
traffic. There is quite a substantial user base that reports proper Ethernet
function with TPlink-4900. This patch is based on the fixes from GINAFAR
maintainer Claudiu Manoli.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38865 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a minor rework of the SDK driver. This driver needs a full rewrite.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38846 3c298f89-4303-0410-b956-a3cf2f4a3e73
get_cycles() is used in some places as one part of the seed for the
kernel PRNG.
This backports the following commit from mainline linux kernel:
9c9b415c50bc298ac61412dff856eae2f54889ee
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38834 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add the profile for the TP-LINK WR842N/ND v2
Small update, because of a change in the Makefile.
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4382/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38815 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add the user space support for the TL-WR842N/ND v2
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4354/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38814 3c298f89-4303-0410-b956-a3cf2f4a3e73
Get the factory assigned mac addresses stored in the caldata
partition and asign them to lan and wan interfaces. Also put
the correct mac addresses into the WiFi eeprom files to ensure
that the ath9k driver will use the correct ones.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Patchwork: http://patchwork.openwrt.org/patch/4350/
[juhosg:
- move WiFi MAC address setup to the firmware hotplug file,
- use the official MAC address for the 2.4GHz as well,
- remove uci-defaults.sh modifications,
- update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38812 3c298f89-4303-0410-b956-a3cf2f4a3e73
- update kernel to 3.12
- add patches for clocks, i2c, usb, sid, rtc
- support common image for A10/A13/A20
- add support for a couple boards
- most drivers are configured into the kernel as of now
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38811 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current implementation of mtd will not append the backup
file created by sysupgrade to the correct partition, as mtd will append
the data to first jffs2 partition it finds. As the kernel is also
stored on a jffs2 partition (which resides before the overlay
partition), the data will be appended to this partition.
To fix this problem, a new option
-s <number> skip the first n bytes when appending data to the jffs2 partiton, defaults to "0"
is added to mtd.
Signed-off-by: Peter Wagner <tripolar@gmx.at>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38807 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some devices are using tty1 as the default console, also swap the early
boot console in such case. This is needed for the WGT634U.
Thank you Russell for reporting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38794 3c298f89-4303-0410-b956-a3cf2f4a3e73
The BCM5365 needs a shift of 7 bits and not 6 bits like the BCM5325 for
the untagged ports.
Thank you Russell for reporting this and testing the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38793 3c298f89-4303-0410-b956-a3cf2f4a3e73
- enable building uboot for imx23 along sbImage by default
- (doc updated)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38781 3c298f89-4303-0410-b956-a3cf2f4a3e73
boardnum is unstable, so allow using NULL to make it unchecked.
A method for differentiating F7D3301 from F7D3302 using nvram is
unknown at this point. Reading the first 32bits of magic from the
"linux" mtd partition would do the trick, but these 2 are similar
enough that we don't need separate led/button definitions. Not knowing
which one you have is only a usability issue for upgrading the device:
they expect different magic numbers for their trx images.
Signed-off-by: Cody P Schafer <devel@codyps.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38767 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is a problem when phydev is not set at this position and not the other way around.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38744 3c298f89-4303-0410-b956-a3cf2f4a3e73
Just fixing up a few things for the Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38733 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add user space support for the TL-WA750RE/WA850RE range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38718 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch to add kernel support for the TP-LINK WA750RE and the WA850RE
range extender
Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com>
[juhosg: rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38717 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes bgmac work without sprom and refreshed the patches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38715 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some more code for bgmac core rev 4 and it now restarts all
cores when initializing the first one on BCM4708. I am just able to
send under 100 packages and then DMA TX does not work any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38714 3c298f89-4303-0410-b956-a3cf2f4a3e73
This pci ID is used by sprom less BCM4313 devices.
This is a backport from the mainline kernel.
This is part of #13551.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38713 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is also known as BCM470{7,8,9}.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38712 3c298f89-4303-0410-b956-a3cf2f4a3e73
- add building of a standard uImage along with the combined kernel+rootfs
- remove 'old' image build - that was for a very old and obsolete bootloader
To update the bootloader for GW2387,GW2388,GW2391 (NOR Flash) from uboot:
put latest NOR bootloader on tftp server:
http://svn.gateworks.com/laguna/trunk/images/u-boot_nor.bin
Laguna> setenv ipaddr <localip>
Laguna> setenv ipaddr <serverip>
Laguna> tftpboot 0x800000 laguna/u-boot-nor.bin
Laguna> erase 0x10000000 +$(filesize)
Laguna> cp.b 0x800000 0x10000000 $(filesize)
Laguna> reset
To update the bootloader for GW2380,GW2382,GW2383 (SPI Flash) from uboot:
put latest SPI bootloader on tftp server:
http://svn.gateworks.com/laguna/trunk/images/u-boot_spi.bin
Laguna> setenv ipaddr <localip>
Laguna> setenv ipaddr <serverip>
Laguna> tftpboot 0x800000 laguna/u-boot-spi.bin
Laguna> erase 0x60000000 +$(filesize)
Laguna> cp.b 0x800000 0x60000000 $(filesize)
Laguna> reset
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38703 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38699 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch makes it possible to use adm6996.c on first generation
BCM47XX devices with ADM switches.
The GPIO bit banging protocol implementation was copied from the old
switch driver and adapted to this driver and changed to the mainline
kernel GPIO interface.
The ADM6996L is different from the ADM6996M which is supported, for
both specs are available in the Internet.
This was tested on a WRT54GS version 1.0, thank you Dirk Neukirchen for
the device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38698 3c298f89-4303-0410-b956-a3cf2f4a3e73
In particular, phy_connect before register_netdev. This is because
register_netdev runs the netdev notifiers, which can race with the rest of
the initialization in ag71xx_probe. In my case this manifested in two ways:
1) If ag71xx is compiled as a module and inserted after netifd has started,
netifd is notified by register_netdev before the call to
ag71xx_phy_connect. netifd tries to bring the interface up, which calls
ag71xx_open, which in turn enters ag71xx_phy_start. This keys off
ag->phy_dev (which is still NULL) and thinks this is a fixed-link board,
and enters ag71xx_link_adjust. This looks at ag->speed which is not yet
initialized and hits the BUG() in the switch (ag->speed) in
ag71xx_link_adjust.
This is the wrong code path for ag71xx_phy_start - my board has PHYs that
need to be brought up with phy_start. Doing ag71xx_phy_connect before
register_netdev ensures that ag->phy_dev is non-NULL before
ag71xx_phy_start is ever called.
2) When ag71xx is built into the kernel, and netconsole is enabled, there
is a gap in the initial burst of replayed printks right after the netdev
comes up. My assumption is that netconsole is also triggered by a netdev
notifier, and part of this printk burst happens before the call into
ag71xx_phy_connect, so part of the burst is lost while the PHY comes up.
This patch fixes the gap - all the printks before eth0 comes up are bursted
in full when netconsole initializes.
ag71xx_phy_connect_xxx no longer runs with a registered netdev, so the
logging has been adjusted accordingly to avoid "unregistered net_device" or
"eth%d" messages in dmesg.
Signed-off-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38689 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg:
- remove the Image/Build/CyberTANLZMA/loader macro, it is not used
- move the MYNETREXT SingleProfile definition to the correct place]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38688 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds a new device definition for a
Western Digital device. The hardware seems to
be based on Qualcomm Atheros DB120 design.
Patchwork: http://patchwork.openwrt.org/patch/4281/
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
[juhosg: refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38686 3c298f89-4303-0410-b956-a3cf2f4a3e73
Append EOF markers to the END of the UBI image
file. This forces the kernel to erase all blocks
after the marker even if those blocks are not
empty.
Additionally, the resulting image can be flashed
from the original web UI now, so use '-factory'
suffix for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38683 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch should prevent overriding of sysupgrade binaries in the bin directory
if we build images for more then one file system type.
Discussion:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-October/022108.html
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38674 3c298f89-4303-0410-b956-a3cf2f4a3e73
The switch is renamed to "switch0" in newer (3.10) linux kernels.
Configure the switch using vlans by default and only configure
the physical switch ports that are present.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38673 3c298f89-4303-0410-b956-a3cf2f4a3e73
Extended the Makefile to generate a working factory reset image
for Netgear WNDR4300. The image uses UBI with two volumes squashfs
(rootfs) and JFFS2 (rootfs_data). In order to make stock U-Boot
happy, a fake rootfs image is placed into the last erase block
of the kernel partition.
Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
- restore the NetgearNAND/initramfs macro,
- remove unused {Squash,Ubi}fsTemplate macros,
- remove board specific mtd options from CONFIG_CMDLINE, append the
board specific ubi.mtd parameter to the kernel command line instead,
- increase kernel partition size to 2MiB,
- use board specific ini file for ubinize,
- put jffs2 eof mark into the rootfs_data ubi volume,
- use KDIR_TMP for temporary images,
- use the squashfs-raw image,
- increase kernel partition size to 2MiB,
- use a local ubinize macro,
- fix macro parameter comments,
- put the fake rootfs into the last erase block of the kernel
partition,
- move Image/Build/NetgearNAND/buildkernel macro before
define Image/Build/NetgearNAND,
- don't use the wndr3700 utility, use '-M' parameter of mkimage to set
the uImage magic,
- use '-recovery' suffix for the generated image, it is only usable via
the fw_recovery function of the bootloader,
- update commit log]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38655 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add new subtarget nand with UBI/UBIFS including GLUEBI and squashfs.
This target will be used for NAND based router which make use of
UBI (and maybe UBIFS later on) in order to provide proper NAND
support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
[juhosg:
- tweak target.mk:
change BOARDNAME variable,
improve Target/Description,
remove targz and ubifs from FEATURES and add broken flag,
- optimize kernel configuration:
disable ubifs, it is not used yet,
disable unused MTD options,
disable SPI support
disable unused network drivers,
tune kernel command line,
- remove image/ubinize.cfg, it will be in a follow-up patch
- move profile modifications into a separate patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38646 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current code only allows to automatically set
root device on MTD partitions. Move the code to MTD
core to allow to use it with all MTD devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38643 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some more bgmac patches from mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38637 3c298f89-4303-0410-b956-a3cf2f4a3e73
Ensures that the 'Default' images are generated
even if the subtarget has no profiles.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38635 3c298f89-4303-0410-b956-a3cf2f4a3e73
The buildbots found some new missing config options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38633 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds the userland support for the Pogoplug E02 by Cloud
Engines, Inc.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38631 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds a DTS file for the Pogoplug E02 by Cloud Engines, Inc.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38630 3c298f89-4303-0410-b956-a3cf2f4a3e73
* use lower case letters in generated images
* extend support for boot/ directory
* fix some typos
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38629 3c298f89-4303-0410-b956-a3cf2f4a3e73
Changes include PCI fixes and various upstream pending patches.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38624 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was spotted by the buildbots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38604 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TEW-692GR images are missing since r36169. Uncomment
the board specific macro in image/Makefile, in order to
generate those again.
Only build tested. No idea if the the image works or not,
I have bricked my TEW-692GR a few months ago.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38603 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- remove MultiProfile, it makes no sense for a single board
- move SingleProfile call and the mtdlayout to a different
location keep things sorted (well, almost)]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38593 3c298f89-4303-0410-b956-a3cf2f4a3e73
BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip.
Patchwork: http://patchwork.openwrt.org/patch/4183/
Signed-off-by: Terry Yang <yangbo@bhunetworks.com>
[juhosg:
- rename and refresh kernel patch,
- fix some checkpatch warnings and adjust whitespaces in
mach-bhu-bxu2000n2-a.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38591 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for DRAGINO2 board (used by
Meshpotato v2). Most of the files included can be
found in the official svn repository provided by the
company [1]. I have just adapt it to the last OpenWrt
trunk revision (Fri Oct 4 10:49:47 2013).
1. http://svn.dragino.com/dragino2
Patchwork: http://patchwork.openwrt.org/patch/4234/
Signed-off-by: Pau Escrich <p4u@dabax.net>
[juhosg:
- rename and refresh kernel patch,
- fix checkpatch warnings in mach-dragino2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38587 3c298f89-4303-0410-b956-a3cf2f4a3e73
Zoltan HERPAI
Imre Kaloz
Hauke Mehrtens
Felix Fietkau
Gabor Juhos
Florian Fainelli
Luka Perkov
Jonas Gorski
John Crispin
Jo-Philipp Wich