This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42193 3c298f89-4303-0410-b956-a3cf2f4a3e73
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42184 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41993 3c298f89-4303-0410-b956-a3cf2f4a3e73
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41932 3c298f89-4303-0410-b956-a3cf2f4a3e73
LED script expects WLAN LED to be "gl-connect:red:wlan".
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41793 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41622 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41618 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41450 3c298f89-4303-0410-b956-a3cf2f4a3e73
sorry, the downside when applying patches with patch
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41350 3c298f89-4303-0410-b956-a3cf2f4a3e73
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40976 3c298f89-4303-0410-b956-a3cf2f4a3e73
This board manufactured by HiWiFi has the following features.
- Atheros 9331 SoC.
- 16MB flash and 64MB RAM.
- 4GB eMMC storage via SK6226 USB 2.0 controller.
- 2 LAN and 1 WAN ethernet ports with LEDs on them.
- 3 blue LEDs on the front panel.
- 1 button labeled as "reset".
- Powered by a USB cable.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40973 3c298f89-4303-0410-b956-a3cf2f4a3e73
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40969 3c298f89-4303-0410-b956-a3cf2f4a3e73
The change is the same as ("kernel/generic: modify mtd related
patches"). Since these files are under files directory, not a files
directory of specific kernel version, better to also change them. So
it will avoid adding files to future specific files directory
(e.g. files-3.14) for this mtd related change.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40732 3c298f89-4303-0410-b956-a3cf2f4a3e73
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40509 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40499 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40479 3c298f89-4303-0410-b956-a3cf2f4a3e73
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40478 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40477 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40475 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40474 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40473 3c298f89-4303-0410-b956-a3cf2f4a3e73
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40400 3c298f89-4303-0410-b956-a3cf2f4a3e73
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.
Features not yet supported:
* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40399 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40032 3c298f89-4303-0410-b956-a3cf2f4a3e73
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39891 3c298f89-4303-0410-b956-a3cf2f4a3e73
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type) * array_size should be used in memset.
Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39890 3c298f89-4303-0410-b956-a3cf2f4a3e73
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39703 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39700 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used for the Mikrotik boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39697 3c298f89-4303-0410-b956-a3cf2f4a3e73
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39641 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Imre Kaloz
Felix Fietkau
Gabor Juhos
Hauke Mehrtens