The setting has been lost during the transition to 3.18.
The CONFIG_M25PXX_PREFER_SMALL_SECTOR_ERASE option is not
available anymore, so use CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45161 3c298f89-4303-0410-b956-a3cf2f4a3e73
The setting has been lost during the transition to 3.18.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45160 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now it at least compiles, otherwise untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45145 3c298f89-4303-0410-b956-a3cf2f4a3e73
There were a few issues with the existing code to detect the model string:
* Always using the string starting with byte 56 would cut off the W of WNDR when
the ID starts with 29763654+16+64 instead of 29763654+16+128
* The string contained garbage after the zero byte instead of cutting it off
after the zero (which wasn't always visible using busybox tools, but could
confuse other scripts)
Tested on a WNDR3700v1 and a WNDR3700v2 using the new 29763654+16+64 ID in the
ART. Furthermore, tested against ART dumps of a WNDR3700v2 using the old
$'\xff...' value and a WNDR3800.
The [ -z "$model" ] check was dropped as there is no way to actually hit this
unless no ART partition is found at all.
The awk command was carefully crafted to work both with gawk and the (horribly
broken) busybox awk.
Fixes#18992.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45140 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is build tested only.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45125 3c298f89-4303-0410-b956-a3cf2f4a3e73
Several targets are not using EMAC_ROCKCHIP so define it in generic config.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45117 3c298f89-4303-0410-b956-a3cf2f4a3e73
because block2mtd wants "erasesize must be a divisor of device size" since 3.15
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45072 3c298f89-4303-0410-b956-a3cf2f4a3e73
the new buildbot was picking this up as a valid target.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45068 3c298f89-4303-0410-b956-a3cf2f4a3e73
Lets hope that this time it won't break the other ralink targets.
Signed-off-by: wengbj <fl.service@t-firefly.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45067 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the xburst target to kernel version 3.18 and also remove the broken 3.10 support.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45031 3c298f89-4303-0410-b956-a3cf2f4a3e73
will re-add it tomorrow after fixing it
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45028 3c298f89-4303-0410-b956-a3cf2f4a3e73
The usb stroage not working since updated 3.18. Porting from MTK's source code.
Signed-off-by: wengbj <fl.service@t-firefly.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45021 3c298f89-4303-0410-b956-a3cf2f4a3e73
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Last time i got some mess . This is new version.
Signed-off-by: Jay Weng <fl.service@t-firefly.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45018 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use `mktplinkfw sysupgrade` or `mktplinkfw factory` or
`mktplinkfw image`
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44998 3c298f89-4303-0410-b956-a3cf2f4a3e73
Should fix pcmcia on BCM6348 and BCM6358 after switching to DT-probed
gpio controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44995 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes the following issue:
drivers/gpio/gpio-bcm63xx.c: In function 'bcm63xx_gpio_probe':
drivers/gpio/gpio-bcm63xx.c:80:4: error: implicit declaration of function 'devm_kasprintf' [-Werror=implicit-function-declaration]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44986 3c298f89-4303-0410-b956-a3cf2f4a3e73
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44985 3c298f89-4303-0410-b956-a3cf2f4a3e73
Respect the vmlinux load address when generating images.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44983 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44982 3c298f89-4303-0410-b956-a3cf2f4a3e73
All images generated contain dtbs, so it is now unused.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44980 3c298f89-4303-0410-b956-a3cf2f4a3e73
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44969 3c298f89-4303-0410-b956-a3cf2f4a3e73
This changes the x86 image generation to match x86_64, using the PARTUUID for
the rootfs instead of explicitly configuring the device.
It unbreaks KVM with VirtIO, which uses /dev/vda2 instead of /dev/sda2.
Tested in QEMU/KVM with VirtIO, VirtualBox and VMware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44966 3c298f89-4303-0410-b956-a3cf2f4a3e73
Otherwise the root device won't be found in 1/16 of the generated images
(whenever the signature starts with a zero digit).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44959 3c298f89-4303-0410-b956-a3cf2f4a3e73
It depends on obsolete compilers and only works on one device (an
evaluation board).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44956 3c298f89-4303-0410-b956-a3cf2f4a3e73
Gabor Juhos
John Crispin
Steven Barth
Rafał Miłecki
Imre Kaloz
Felix Fietkau
Luka Perkov
Florian Fainelli
Zoltan HERPAI
Lars-Peter Clausen
Jonas Gorski
Jo-Philipp Wich