apparently this one was nt a good idea to merge
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40330 3c298f89-4303-0410-b956-a3cf2f4a3e73
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40329 3c298f89-4303-0410-b956-a3cf2f4a3e73
ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in
flash as big-endian, but the driver needs it in little-endian format. We
have to swab it before handing it over. This requires my earlier patch
for busybox.
Funnily enough, ARV752DPW works also with the incorrect eeprom, but
undoubtedly unoptimally. I have a hunch that also the final remaining
Lantiq board would require this swabbing, but I'm not sure, so I just
swab it in the three boards that I know about.
v2:
* Swab also on ARV7510PW22 based on feedback from Alvaro Rojas
* Fix the offset with bs=2
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40328 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some boards have the WLAN EEPROM stored in flash in big-endian format,
whereas the driver requires the EEPROM in little-endian format. The
conv=swab option in dd is particularly useful in this case. This patch
backports this feature from busybox-1.22 based on the following commits:
commit b941316ae5313be523b64f0a9151ee4decb2b35b dd: support conv=swab
commit 8395bd3f52f8ed46fa3ffc316b2d113afa748bae dd: fix example in a
comment. No code changes.
commit 5b9910f0a4a1b7976c46e6f849aaa263180e5521 dd: fail if swab is
attempted on odd-sized block
commit 0ff0b320a2dbb5e0b5fa245ffd9b2648d7026843 dd: code shrink
v2: include the commit messages from upstream
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40327 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ltq-adsl-mei driver allocates memory for the ADSL firmware in a
rather stupid way, leading to several 128k allocations, which fail when
many services are enabled. This patch tries to allocate 64 kiB chunks,
and only falls back to larger allocations if the returned pointers are
not correctly aligned. Fixes out-of-memory errors on Danube boards with
32 MiB RAM.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40325 3c298f89-4303-0410-b956-a3cf2f4a3e73
The existing code only tries to split a parition with name "rootfs"
while actually looking for kernel+rootfs, where usually "firmware" is
used as a partition name. This doesn't make sense, as even if there
was a partition 'rootfs' given by mtdparts or via device-tree, this
code would lead to another partition called 'rootfs' being created
which would not be properly distinguished in the current user-space
code.
While potentially we could use CONFIG_MTD_SPLIT_FIRMWARE_NAME to make
that configurable, the lack of users of brnboot and the fact that we
can freely decide the partition name made me simply change the
hard-coded string constant from "rootfs" to "firmware".
(I'm going to add support for ARV7506PW which run brnboot and needs
this change)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40324 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Set correct AltSel for STP pins
- Set front button to rfkill
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40320 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40319 3c298f89-4303-0410-b956-a3cf2f4a3e73
If gphys are not reset upstream uboot can not use them anymore.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40318 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40317 3c298f89-4303-0410-b956-a3cf2f4a3e73
Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags
are reversed. Full duplex is marked as half and the other way around. With this
fix the switch will push full GBit speeds.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40312 3c298f89-4303-0410-b956-a3cf2f4a3e73
Export the ubi_num and vol_id into the sysfs record of the gluebi-
emulated mtd device. Previously userspace didn't have a way to
map gluebi-emulated devices back to their corresponding ubi volumes.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40306 3c298f89-4303-0410-b956-a3cf2f4a3e73
If the CPU port is not forced up, the link, at least on this board, is lost after
changes are applied. This makes sure that the link is restored. Regression tests
should confirm it doesn't break other boards.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40305 3c298f89-4303-0410-b956-a3cf2f4a3e73
- hide port pvid - vlan index relation
- switch initialises with vlans disabled so port isolation is not used
- remove special treatment of cpu port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40304 3c298f89-4303-0410-b956-a3cf2f4a3e73
Changes to:
- show the correct "enable_vlan" value under "Global attributes"
- show tagged ports under "Vlan: ports"
- use get_port_link method to report link status
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40303 3c298f89-4303-0410-b956-a3cf2f4a3e73
the unshare utility wasn't getting certain defines for mount
anymore.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40302 3c298f89-4303-0410-b956-a3cf2f4a3e73
fixes incremental build with change to CONFIG_DROPBEAR_ECC
drop --with-shared which is unknown to configure
Patch by Catalin Patulea <cat@vv.carleton.ca>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40300 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without timeout mechanism, if ssh client disconnected without sending
FIN or RST, forked dropbear servers would hang there for
KEX_RETRY_TIMEOUT seconds (8 hours).
TCP keepalive is not implemented in dropbear yet, thus the name
SSHKeepAlive.
300 seconds in this patch is selected from the default value of
ServerAliveInterval for Debian ssh client (See man ssh_config).
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40299 3c298f89-4303-0410-b956-a3cf2f4a3e73
The antenna gain attribute has been removed from the upstream regulatory database.
Incorperate patch from Luis R. Rodriguez to skip the parsing of the gain attribute
in genregdb.awk in order to emit proper rules again.
Also refresh fuzzy patches while we're at it.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40296 3c298f89-4303-0410-b956-a3cf2f4a3e73
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40038 3c298f89-4303-0410-b956-a3cf2f4a3e73
The version of TL-WDR4300 sold in Israel comes with a different
hardware id.
Patch-by: Daniel <daniel@makrotopia.org>
Patchwork: http://patchwork.openwrt.org/patch/5001/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40037 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40032 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Felix Fietkau
Jo-Philipp Wich
Imre Kaloz
Gabor Juhos