This package is required for network drivers such as pcnet32
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38530 3c298f89-4303-0410-b956-a3cf2f4a3e73
The switch driver is not used by brcm47xx any more and can be removed,
instead of this switch driver b53 is used now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38387 3c298f89-4303-0410-b956-a3cf2f4a3e73
Config options in backports are starting with CPTCFG and not with CONFIG_.
CONFIG_B43_BCMA was never true.
This closes#13883.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38385 3c298f89-4303-0410-b956-a3cf2f4a3e73
These URLs where missing and causes build failures.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38376 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes compilation for linux 3.10.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38367 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update proc code to new proc_create to allow compilation with
linux 3.10+.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38366 3c298f89-4303-0410-b956-a3cf2f4a3e73
WL_TI is bool but was set to =m, which deactivated it. Now it is set to
=y and should be activated in the config so the wl12xx driver gets
build.
This closes#14212.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38333 3c298f89-4303-0410-b956-a3cf2f4a3e73
Somehow BRCMFMAC_USB was not set in the build and brcmfmac.ko did not had usb support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38332 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change the autoload number from '5' to '05' so the module loads earlier (as intended).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38293 3c298f89-4303-0410-b956-a3cf2f4a3e73
it has a conditional #ifdef based dependency on it, which trips up on
some targets
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38242 3c298f89-4303-0410-b956-a3cf2f4a3e73
Should fix build errors with Linux 3.3/3.6 targets, which use different
kconfig symbols
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38238 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for the ADT7410 hwmon driver, a high precision
I2C temperature sensor.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[juhosg: update subject, reformat commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38186 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move pca953x support from i2c.mk to other.mk, where other
GPIO drivers are located. Remove duplicate pcf857x support
from i2c.mk.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[juhosg: update subject, and reformat commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38185 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38036 3c298f89-4303-0410-b956-a3cf2f4a3e73
now that we have modprobe we can set more than half of the modules to AutoProbe
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38021 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thank you Javier Achirica for the patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38008 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38001 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37977 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most of the Linksys devices without an own GPIO configuration where
detected as WRT54G. On one board this made OpenWrt to boot into
failsafe every time, because one GPIO configurated as button was not a
button.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37970 3c298f89-4303-0410-b956-a3cf2f4a3e73
The imx sata module has only been backported to imx6 target. This change will
fix buildbot errors due to missing patches in other targets. Keep this until
all targets use kernel version with imx sata support in them.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37950 3c298f89-4303-0410-b956-a3cf2f4a3e73
- enable using hwmon GSC driver on all targets
- add a kmod package for it
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37933 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the following error:
firewire_core: Unknown symbol crc_itu_t (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37902 3c298f89-4303-0410-b956-a3cf2f4a3e73
linux-firemware contains the same version we loaded without this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37901 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the following error:
xfs: Unknown symbol exportfs_decode_fh (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37900 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes the following error:
keyspan: Unknown symbol ezusb_fx1_ihex_firmware_download (err 0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37899 3c298f89-4303-0410-b956-a3cf2f4a3e73
This enables usage of the ath10k driver on OpenWrt. Only 2.0 PCI hardware
is supported. The ath10k firmware is currently only available
through github so use that as its source for now.
This goes build tested, not run time tested.
[Hauke: I did some minor changes]
Cc: ath10k@lists.infradead.org
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Mathieu Olivari <mathieu@qca.qualcomm.com>
Cc: Jerome Proffit <jproffit@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Matthew McClintock <mmcclint@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37898 3c298f89-4303-0410-b956-a3cf2f4a3e73
The package makes it possible to create custom SPI
buses via GPIO lines.
This module is based on i2c-gpio-custom and allows to
configure an SPI bus via GPIO lines and expose it to
userspace without rebuilding the kernel. This is maily
intended to connect microcontrollers and other simple
SPI devices without making an ad-hoc kernel driver.
Signed-off-by: Marco Burato <zmaster.adsl@gmail.com>
[juhosg:
- change subject,
- extend and reformat commit message,
- cleanup checkpatch errors/warnings in module source]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37872 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thanks to Berni, Adam Novak and Sedat Dilek for patches and inspiration
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37866 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport some rt2x00 specific changes from
wireless-testing/master-2013-08-26 to add
support for RT3573 based devices.
Also refresh the rt2x00 specific patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37843 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was itriggered by to many non buffalo devices
This closes#14043.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37804 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is partly based on patches sent by Łukasz Kwestarz (See https://lists.openwrt.org/pipermail/openwrt-devel/2012-March/014356.html).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37802 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the "start_disabled" option in hostapd that was added
in the earlier patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37732 3c298f89-4303-0410-b956-a3cf2f4a3e73
The BCM4331 supports a PCIe max request size of 512 bytes and uses
that, but the PCIe controller in the BCM4706 just supports 128 Bytes
and that causes a DMA error for packages bigger than 126 bytes. This
fixes the problem by setting the BCM4331 also to 128 Bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37709 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current dependency prevents building of the
rt2800{pci,usb} drivers for RT3883. Change the
dependency to fix this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37699 3c298f89-4303-0410-b956-a3cf2f4a3e73
When CONFIG_LLC gets build as a module, also p8022.ko and psnap.ko are
getting build as a module. kmod-appletalk depends on llc.ko and
psnap.ko, but at least psnap.ko,was not packed. On most systems
CONFIG_LLC will be build into the kernel so this problem does not show
up.
This fixes the missing dependency of kmod-appletalk on psnap.ko
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37673 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds button and led info, which I determined
by manually poking the gpio values.
Signed-off-by: Josh Stone <cuviper@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37655 3c298f89-4303-0410-b956-a3cf2f4a3e73
TL-WR720N-v3 has a slider switch composed of 2 GPIO buttons which can be
used to swtich between 3 positions. At leat 1 button is in pressed state
in any of those positions. Initialize 'last_state' as 0 (released) will
cause the device to automatically enter failsafe mode on every bootup.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37643 3c298f89-4303-0410-b956-a3cf2f4a3e73
Comparing the RTSDK driver and mac80211 revealed, that this register needs
to have a special setup on rt5350.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37608 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables setting the wifi led polarity from OF.
It can be used in a DTS' wmac section like this:
ralink,led-polarity = <1>;
Valid values are 0 or 1.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37607 3c298f89-4303-0410-b956-a3cf2f4a3e73
based on http://patchwork.openwrt.org/patch/3827/
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37562 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch modifies the uci scripts to be able to
start meshd-nl80211 for encrypted mesh networks,
therefor a new script (authsae.sh) is inserted.
Signed-off-by: Emanuel Taube <emanuel.taube@gmail.com>
[etienne.champetier@free.fr: just update mac80211.sh path]
Signed-off-by: Etienne CHAMPETIER <etienne.champetier@free.fr>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37554 3c298f89-4303-0410-b956-a3cf2f4a3e73
Properly define the config symbol to n so it doesn't break build for
targets which do have it available (e.g. mostly everything except arm).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37489 3c298f89-4303-0410-b956-a3cf2f4a3e73
This forces all packets (even for un-aggregated traffic) through
software queues to improve fairness and stability
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37483 3c298f89-4303-0410-b956-a3cf2f4a3e73
Florian Fainelli
Felix Fietkau
Luka Perkov
Hauke Mehrtens
Jonas Gorski
John Crispin
Gabor Juhos
Steven Barth