The AT91 SAMA5D3XPLAINED uses a KSZ9031 and a KSZ8081 that are supported
by this PHY driver.
Backport of r46171
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46416 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r46410
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46411 3c298f89-4303-0410-b956-a3cf2f4a3e73
This should fix build of sunxi.
Backport of r46304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46310 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add features ext4 targz to target x86/xen_domu in order to
generate images in defconfig.
This fixes#18074.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Backport of r46233
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46277 3c298f89-4303-0410-b956-a3cf2f4a3e73
r45954 ("ar71xx: fix 100/10mbps ethernet link issues on mynet range
extender") introduced a pdata based modification of the tx_clk_dly. But it
was not checked if pdata actually existed. This caused a page fault on all
devices which didn't have at803x_platform_data specified for an at803x
based device.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Backport of r46200
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46252 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also move it to an earlier place so new boards added are less likely
to confuse quilt.
Fixes#19965.
Backport of r46148.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46153 3c298f89-4303-0410-b956-a3cf2f4a3e73
On two tested devices: Netgear R6250 (BCM53011 rev 2) and Luxul XWC-1000
(BCM53011 rev 3) it was possible to use port 7 and eth1 (instead of port
5 and eth0). It seems BCM53011 just like BCM53012 has 8 ports and
usually 3 of them are connected to the SoC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r46104
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46107 3c298f89-4303-0410-b956-a3cf2f4a3e73
This drops some debugging pr_info and adds platform_device_unregister.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r46082
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46098 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
Backport of r46049
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46059 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
Backport of r46048
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46058 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
Backport of r46047
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46057 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Backport of r46046
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46056 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
Backport of r46044
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46054 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Backport of r46043
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46053 3c298f89-4303-0410-b956-a3cf2f4a3e73
http://wiki.openwrt.org/toh/d-link/dcs-930l
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Backport of r46042
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46052 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
Backport of r46041
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46051 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: John Crispin <blogic@openwrt.org>
Backport of r46038
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46039 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r46032
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46033 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is required to use x86/64 in KVM containers with VirtIO disks
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Backport of r46017
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46018 3c298f89-4303-0410-b956-a3cf2f4a3e73
It seems that there are maximum timings for mdio accesses that can be
hit when the system is under load and the thread is scheduled during
a read or write access. Since there is no way of knowing if this
happens as there is not even a parity bit, try to work around it
by disabling interrupts during any gpio-mdio accesses.
Performance impact seems to be neglectable, as mdio accesses are not
that often.
Hopefully fixes#19500.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Backport of r46012.
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46016 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r46007
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46009 3c298f89-4303-0410-b956-a3cf2f4a3e73
This stabilizes USB support. The old patch was handling initialization
in a different order that was causing some problems with few USB 3.0
devices. Some weren't detected, some were working unstable, sometimes
USB 3.0 could hang the whole controller.
A still known issue (but not a regression) is controller hang triggered
by connecting USB 1.1 device when not having OHCI controller enabled
(kmod-usb-ohci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Backport of r45997
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@45998 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Backport of r45992
git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@45993 3c298f89-4303-0410-b956-a3cf2f4a3e73
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45970 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45965 3c298f89-4303-0410-b956-a3cf2f4a3e73
The *u-boot-initramfs* images are not ITB/FIT images but are rather
supposed to be loaded to RAM and jumped-into.
To avoid confusion, change the file extension from itb to bin.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45963 3c298f89-4303-0410-b956-a3cf2f4a3e73
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes#19751, bug introduced in #45624
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45958 3c298f89-4303-0410-b956-a3cf2f4a3e73
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45954 3c298f89-4303-0410-b956-a3cf2f4a3e73
When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.
Fixes#19836.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45945 3c298f89-4303-0410-b956-a3cf2f4a3e73
On device reset the sizes for the vlan and port tables were wrongly
calculated based on the pointer size instead of the struct size. This
causes buffer overruns on 64 bit targets, resulting in panics.
Fix this by dereferencing the pointers.
Reported-by: Fedor Konstantinov <blmink@mink.su>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45938 3c298f89-4303-0410-b956-a3cf2f4a3e73
At least on my b53 chip, the mask is 3 bits wide, and because
of this some STP states are not set properly and discarded when read.
Maybe for some other chips it makes sense to have just 2 bits width,
but I don't have other versions around to test/validate.
If that's the case then maybe we could add another STP state mask.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45937 3c298f89-4303-0410-b956-a3cf2f4a3e73
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45919 3c298f89-4303-0410-b956-a3cf2f4a3e73
Extracting TRX to separated file in /tmp/ just wastes some RAM while we
can just pass a proper extracting command to the default_do_upgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45912 3c298f89-4303-0410-b956-a3cf2f4a3e73
Extracting full TRX out of vendor format is not needed as otrx supports
passing TRX offset. This saves some RAM during sysupgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45911 3c298f89-4303-0410-b956-a3cf2f4a3e73
The v1 identifies as v10 internally. As there is no TL-WA830RE v10, add a
workaround to avoid confusing users.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45903 3c298f89-4303-0410-b956-a3cf2f4a3e73
Version 2 : White spaces and alphabetical order problems
fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware
Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45902 3c298f89-4303-0410-b956-a3cf2f4a3e73
Extracting TRX to separated file in /tmp/ requires extra RAM which may
not be available on some chepaer devices. Instead of that lets pass a
proper extracting command to the default_do_upgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45901 3c298f89-4303-0410-b956-a3cf2f4a3e73
if there is any new tx need to clean up. do it in next napi poll.
collect tx related members to fe_tx_ring struct. for better
cache usage and more readable.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45895 3c298f89-4303-0410-b956-a3cf2f4a3e73
when open device. first ready napi software rx.
then enable hardware interrupt.
final start software tx queue to send data.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45894 3c298f89-4303-0410-b956-a3cf2f4a3e73
Avoid the use of memory marked as reserved
MT7621 support 512MB memory.
According to "MT7621_ProgrammingGuide_Preliminary_Platform.pdf"
0x0~0x1c000000 448MB
0x20000000~0x4000000 64MB
total 512MB
Signed-off-by: wengbj <fl.service@t-firefly.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45892 3c298f89-4303-0410-b956-a3cf2f4a3e73
This also adds the old hardcoded value to the VGV7519BRN profile to make
sure that images are still generated correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45882 3c298f89-4303-0410-b956-a3cf2f4a3e73
Livebox does need the uncompressed kernel, so just create it during
image generation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45875 3c298f89-4303-0410-b956-a3cf2f4a3e73
Ethernet GMAC is built-in the SoC, so there is no need to enable it as a
module. We'll just assume we need it. That's what is done for other
platform where this driver is used so it'll make things more consistent.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45871 3c298f89-4303-0410-b956-a3cf2f4a3e73
Delete the dtb appended, uncompressed kernels after having compressed
them, so they don't end in the image builder.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45869 3c298f89-4303-0410-b956-a3cf2f4a3e73
In r44391 the kernel partion size was increased to allow larger kernels,
but the rootfs partition offset was missed. Fix this by setting the
rootfs offset to the expected value.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45868 3c298f89-4303-0410-b956-a3cf2f4a3e73
I didn't figure out how to achieve this using uci-defaults-new.sh,
so use old-school uci-defaults script as that's what is used on
realview as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45857 3c298f89-4303-0410-b956-a3cf2f4a3e73
Building the loader in Image/Build/TPLINK-SAFELOADER would break the image
builder as no target compiler is available in that stage.
Fixes#19580
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45855 3c298f89-4303-0410-b956-a3cf2f4a3e73
In contrast to Image/BuildLoader, Image/BuildLoaderPatched first patches the
kernel command line in the image and then builds the loader without command
line. This allows building loaders for systems which don't boot correctly when
the kernel command line is provided by the loader (like the TP-LINK CPE series).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45854 3c298f89-4303-0410-b956-a3cf2f4a3e73
move the patch to the proper folder
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45848 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most boards use pci connected usb controllers, so make sure to include
the pci drivers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45840 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is the case e.g. if JFFS2 partition is full.
see: https://www.mail-archive.com/linux-unionfs@vger.kernel.org/msg00246.html
(a small error in a logmessage was changed and reported upstream)
runtime tested on ar71xx with kernel 3.18.11 and r45772
this paritially fixes#19564
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45833 3c298f89-4303-0410-b956-a3cf2f4a3e73
This driver has been cherry-picked and backported from the following
LKML thread:
*https://lkml.org/lkml/2015/5/26/744
It also updates the DT accordingly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45831 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most ipq806x platforms use an ethernet switch, and the new upstream
GMAC driver makes use of the Fixed PHY emulation to force the link
settings despite the lack of PHY.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45830 3c298f89-4303-0410-b956-a3cf2f4a3e73
STMMAC_PLATFORM and STMMAC_PCI have been added recently in the kernel,
but show up only when STMMAC driver is enabled. So se'll add it in the
generic config, so the kernel build doesn't stall whenever we enable
this driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45828 3c298f89-4303-0410-b956-a3cf2f4a3e73
This include is necessary starting at the PCIe patch, which has a lower
number. So in order to keep the patches consistent, we'll move the
arm-gic include in the first patch who needs it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45827 3c298f89-4303-0410-b956-a3cf2f4a3e73
this treacled down via the stable tree and wandered into 3.18.14
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45793 3c298f89-4303-0410-b956-a3cf2f4a3e73
Turn on the auto recovery feature when flashing
and turn it off on successful bootup.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45792 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch the following two patches are backported:
* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down
The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45783 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update kernel sources and refresh some patches.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45761 3c298f89-4303-0410-b956-a3cf2f4a3e73
Florian Fainelli
Felix Fietkau
Hauke Mehrtens
John Crispin
Jonas Gorski
Rafał Miłecki
Jo-Philipp Wich
Imre Kaloz