a4e54ee1c8
generic: disable 'small sector' erase in m25p80 driver
...
This fixes the issues with the jffs2 images on various boards. Using
JFFS2 on devices with 4KiB erase sectors is not safe:
http://lists.infradead.org/pipermail/linux-mtd/2011-June/036591.html
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29521 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-13 20:41:22 +00:00
af9ac63fda
kernel: move linux/ath9k_platform.h to generic files so that it can be reused from other targets
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29516 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-13 15:14:59 +00:00
f5ed3d653f
ar71xx: fix wireless led on wzr-hp-g450h
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29515 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-13 15:00:43 +00:00
2329eaffac
ar71xx: enable AR9341 support at setup.c
...
Patch-by: dyq <729650915@qq.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29514 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-13 14:59:43 +00:00
041a6265f8
ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
...
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29513 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-13 14:59:40 +00:00
9db5641019
ar71xx: add gpios and usb for wzr-hp-g450h
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29509 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-13 13:33:44 +00:00
c9fcfa6fba
ar71xx: use RedBoot parser on PB44
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29501 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-11 15:52:47 +00:00
2d08ff0a1b
[atheros] convert to gpiolib
...
Signed-off-by: karlp@tweak.net.au
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29486 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-09 07:52:10 +00:00
589a8dfc24
ar71xx: fix WNDR3x00 factory image generation
...
Factory images for WNDR3700v2 and WNDR3800 should contain these model IDs
for the device: field in their DNI tags, not WNDR3700.
This regressed in r29434, which redid WNDR3x00 model detection. The sixth
parameter to Image/Build/Netgear is only used as the -B argument to
mkdniimg, which is used to set the device: field. In r29434, this was
erroneously changed to be WNDR3700 for all models. The tools to flash
factory images (U-Boot's TFTP server and the factory software's upgrade
utility) may refuse to honor images with incorrect device: fields in their
DNI tags.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29473 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-07 06:55:50 +00:00
dbdb71ce8b
ar71xx: fix WNDR3x00 model detection
...
Detect the model name for /tmp/sysinfo/model based on 10 bytes at offset
56 in the art (caldata) mtd partition.
r29434 redid WNDR3x00 model detection, attempting to distinguish between
WNDR3700v2 and WNDR3800 by checking MemTotal in /proc/meminfo. However, it
contained a bug: it put the awk inside a $(...), with the result that all
WNDR3700v2 and WNDR3800 models would be reported as WNDR3800. This patch
checks the model name stored in the art partition, as is done by U-Boot
shipping on the WNDR3800. It has the likely advantage of working with
future models based on the WNDR3700 board. It also will not mis-detect
units on which people install more memory.
I have tested this patch on WNDR3700 (v1), WNDR3700v2, and WNDR3800.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29472 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-07 06:55:39 +00:00
bee30c2698
ramips: fix mac addresses on the DIR-300/600 boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29471 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06 20:06:08 +00:00
77eea315ca
linux: update 3.1 to 3.1.4
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29470 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06 19:50:30 +00:00
4baeaf652e
linux: update 3.0 to 3.0.12
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29469 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06 19:50:25 +00:00
4636ce7f8a
ar71xx: create firmware image for the TL-WR740N/ND v4 boards
...
Based on a patch by Cristian Deluxe <djcristiandeluxe@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29468 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06 16:26:44 +00:00
33322c055c
ar71xx: use hw_id, hw_rev and flash_layout with mktplinkfw
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29467 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06 16:26:43 +00:00
8244420b66
ar71xx: fix TL-MR3x20 profile names in image/Makefile
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29463 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06 13:53:21 +00:00
554d2c4504
ar71xx: cleanup TP-Link profiles
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29461 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-06 10:29:25 +00:00
bdfd4b5e5f
ar71xx: add TP-Link board detection
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29459 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 21:11:01 +00:00
10ebaf63a7
ar71xx: use correct mac on the lan interface on several TP-LINK devices
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29458 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 21:10:58 +00:00
9501b2cf37
ar71xx: allow to pass negative offset values for ar71xx_init_mac
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29457 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 21:10:55 +00:00
8caa31435f
ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29456 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 18:21:15 +00:00
e8c0dabf9a
ar71xx: verify hardware id of firmware images on TP-Link boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29455 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 18:11:51 +00:00
287e495fdd
ramips: set mac addresses for the NBG-419N
...
Based on a patch by Nerijus Baliunas <nerijus@users.sourceforge.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29454 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 17:27:07 +00:00
306d52b8da
ramips: set preinit interface mac on the hw550-3g board
...
Based on a patch by Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29453 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 17:27:06 +00:00
953b52d306
ramips: use ramips_get_mac_* functions in the preinit script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29452 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 17:27:04 +00:00
dcaa1e228c
ramips: move ramips_get_mac_* functions to lib/ramips.sh
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29451 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 17:27:03 +00:00
f2e2c7bc03
ramips: add ramips_ prefix to get_mac_{binary,nvram} functions
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29450 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 17:27:02 +00:00
d0e8df7341
ramips: fix network configuration setup
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29448 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 16:54:48 +00:00
6356c4e99d
ar71xx: reclaim some unused space on TP-Link boards
...
With the default OpenWrt configuration, this increases the size
of the rootfs_data partition by 384KB/128KB on the older/newer
TP-Link models.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29447 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 14:52:36 +00:00
bb48c3c03e
ar71xx: check squashfs signature in TP-Link mtd parser
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29446 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 14:52:33 +00:00
c9f52e0adc
ar71xx: use the lzma-loader on TP-Link boards w/o lzma support
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29444 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 14:52:28 +00:00
f59dd2dc3e
ar71xx: add lzma loader
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29443 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 14:52:25 +00:00
037fc54211
ar71xx: add preliminary support for wzr-hp-g450h
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29441 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 14:20:51 +00:00
0eb86d9380
ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29440 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 14:20:44 +00:00
a86d2fb99b
ar71xx: rewrite WNDR3700/3800 handling
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29434 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 13:03:54 +00:00
40cbea9b54
[ar71xx] add some missing wndr3800 base-files definitions
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29433 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 12:56:21 +00:00
65d271e73a
ar71xx: change user-space board detection
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29432 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 12:56:20 +00:00
32baf22378
ar71xx: allow WNDR3700 image creation to fail if kernel/rootfs too big
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29431 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-05 12:47:53 +00:00
0dd3da8e65
ramips: fix argus board rootfs size
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29422 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-04 15:24:57 +00:00
e4bdc2f753
ar71xx: use the tp-link parser on the tp-link boards
...
Also remove static partition maps.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29416 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 18:13:31 +00:00
dc7ac75841
ar71xx: add mtd partition parser for the TP-Link boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29415 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 18:13:27 +00:00
f91daa7486
ar71xx: run the RedBoot parser only on the RedBoot based boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29414 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 18:13:25 +00:00
c4126790b7
ar71xx: run the MyLoader parser only on the WP543 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29413 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 18:13:23 +00:00
2216dd22b0
ar71xx: run the wrt160nl parser only on the WRT160NL board
...
Also remove static mtd partition definitions.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29412 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 18:13:20 +00:00
b6c404e141
ar71xx: allow to pass part_probe types to the m25p80 driver
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29411 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 18:13:18 +00:00
c7c70fbb89
ar71xx: create initramfs images for the newer TP-Link boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29410 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 16:57:23 +00:00
f706282640
ar71xx: remove swconfig and wpad-mini from custom profiles
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29408 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 16:33:41 +00:00
e008acff75
ar71xx: add uboot-envtools to the default package list
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29407 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 16:33:40 +00:00
0f72e36a61
ar71xx: reclaim unused space in WNDR3700/3800 images
...
Patch by: Mark Mentovai <mark@moxienet.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29406 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-03 16:33:38 +00:00
d55531f7b7
ar71xx: add a profile and build image for the OM2P board
...
[juhosg: the name of the final image has been changed to
'openwrt-ar71xx-generic-om2p-squashfs-factory.bin']
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29397 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:49:05 +00:00
897691c597
ar71xx: add support for Ubiquiti AirRouter
...
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29395 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:49:02 +00:00
64834fd3a6
ar71xx: configure default led behavior for the OM2P
...
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29394 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:59 +00:00
7e3d291cee
ramips: enable sysupgrade on the RT-N15 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29393 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:58 +00:00
15b6e5575c
ramips: wrap long line in platform upgrade script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29392 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:57 +00:00
85c9f9860b
ramips: add profile for the Asus RT-N15
...
This uses previously submitted rtl8366 kernel packages.
[juhosg: The kmod-gpio-dev package has been removed from the package list.]
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29391 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:55 +00:00
d1754575ec
ramips: setup default network configuration for RT-N15
...
Based on a patch by Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29390 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:54 +00:00
68c76b9f54
ramips: rt288x: add swconfig and rtl8366{s,_smi} drivers to the default profile
...
It is needed by the RT-N15 board.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29389 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:53 +00:00
0aaf068e51
ramips: remove default network configuration, and generate that from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29387 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:51 +00:00
cebe9384fa
ramips: use /lib/functions/uci-defaults.sh
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29386 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:48 +00:00
c2898515e9
ar71xx: use /lib/functions/uci-defaults.sh
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29385 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:47 +00:00
46cb8a93ff
ramips: simplify uci-defaults/network script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29383 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:45 +00:00
1c16097588
ramips: setup mac and network interfaces from separate functions
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29382 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:43 +00:00
33678d2d30
ramips: fix Asus RT-N15 board support
...
Fix Asus RT-N15 flash partitions and make an image.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29381 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:42 +00:00
f25326846b
ramips: Sparklan wcr-150gn board fixes
...
* Fix partition sizes.
* Add buttons and leds.
* Register usb.
* Remove unnecessary stuff from image Makefile
* Fix rt2x00 eeprom extract.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29380 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:41 +00:00
a253c0d6fb
ramips: fix package name of kmod-input-gpio-buttons
...
Based on a patch from Omnima Limited.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29379 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:39 +00:00
12ebf7f0a8
ramips: move kmod-rt2800-pci to DEFAULT_PACKAGES
...
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29378 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:38 +00:00
c42e834587
ramips: setup bc2 mac addresses from the generic network script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29377 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:37 +00:00
576ea7dee8
ramips: combine network setup for all boards in one file
...
Inspired by the patch from Roman Yeryomin. Thanks, Roman!
This removes unnecessary duplication and simplifies network setup for new
boards. It would be a one line change most likely.
[juhosg: setup lan and wan interfaces for unspecified rt3x0x based boards
in order to avoid regression]
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29376 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-12-01 22:48:35 +00:00
2b4010111d
omap24xx: bump to 3.1.3
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29349 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-28 12:46:18 +00:00
35fe83070a
lantiq: bump to 3.1.3
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29348 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-28 10:22:58 +00:00
c2bdcfd9f2
targets: fix CONFIG_USB_STORAGE_* inconsistency
...
* all options were switched from bool to tristate in 2.6.30
* add/change/move them to generic, disabled by default
* remove extinct CONFIG_USB_STORAGE_DPCM dropped in 2.6.29, merged with CONFIG_USB_STORAGE_SDDR09
* remove extinct CONFIG_USB_STORAGE_SIERRA option in 2.6
* cleanup ordering
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29337 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-25 20:47:44 +00:00
dcab0017e4
ar71xx: modify phy mask of the WP543 board
...
This fixes ethernet on newer boards. Based on a patch from #9702 .
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29328 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-24 20:09:43 +00:00
dc19d51869
ar71xx: fix wndr3800 machine name
...
This fixes the machine name in /proc/cpuinfo and luci status page machine name.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29326 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-24 20:09:38 +00:00
1df32b6140
ar71xx: copy atheros initramfs images to the image directory
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29325 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-24 20:09:35 +00:00
f738f055b7
ar71xx: specify mtd layout in command line for the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29324 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-24 20:09:32 +00:00
78a3a35804
lantiq: drop 009-MIPS-make-oprofile-use-cp0_perfcount_irq-if-it-is-se.patch
...
This patch is/was a duplicate of generic/patches-3.1/307-mips_oprofile_fix.patch
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29294 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-23 12:22:15 +00:00
3e358d18e2
lantiq:
...
* fixes ath5k eeprom handling
* fixes sx76x
* adds sx76x to userland api
* minor style cleanups
Signed-of-by: Andrej Vlašić <andrej.vlasic0@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29292 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-22 18:50:51 +00:00
3361c4d1bf
[brcm63xx] don't package gpioctl by default
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29288 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-21 16:36:39 +00:00
29e5ed5992
target/uml: export atomic64_* functions on 32-bit x86
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29287 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-21 14:28:33 +00:00
4c134d64ea
ar71xx: set GE0 phy_mask for AR933x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29274 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-20 11:30:10 +00:00
d724cd4a24
[brcm63xx] fix D-Link DSL-2650U image generation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29266 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-19 21:34:51 +00:00
16fd48e131
linux: update 3.0 to 3.0.9
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29264 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-19 18:39:12 +00:00
7d6a631816
[brcm63xx] build images for D-Link DSL-2650U ( #9003 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29238 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-18 10:37:03 +00:00
71954c593e
omap24xx: Fix cbus nested IRQ acking
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29237 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-17 22:31:27 +00:00
b22066dc6f
omap24xx: Fix initialization of software IRQ mask
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29236 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-17 21:02:00 +00:00
d976d63d95
omap24xx: Update 3.1 config
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29234 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-17 19:35:57 +00:00
53f6feb557
omap24xx: Some retu/tahvo IRQ fixes
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29233 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-17 18:06:19 +00:00
48937bced2
omap24xx: Add basic kexec fixes.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29232 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-17 14:57:34 +00:00
46a5094e4e
omap24xx: Add workaround for omapfb locking bug.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29201 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-16 22:34:38 +00:00
0da89768b6
Revert r29193
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29195 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-16 19:03:23 +00:00
cf42d675f5
omap24xx: Set platform specific optimization flags
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29194 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-16 19:02:12 +00:00
59676bb6a3
n810: Add xmodmap to profile
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29193 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-16 19:01:19 +00:00
60662c31e9
[rdc] include bridge and 8021q modules by default
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29164 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-15 22:24:22 +00:00
c8c032629a
lantiq: add runtime generation of /etc/config/network
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29161 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-15 18:21:00 +00:00
8f83f4a62f
lantiq: fix falcon build breakage
...
dev-wifi-rt2x00 fails to build on falcon due to missing pci
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29129 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 18:55:58 +00:00
0ec8a8b387
ar71xx: fix USB LED on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29126 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 17:43:15 +00:00
a8b9399527
ar71xx: add a function for selecting output signal on a given GPIO pin
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29125 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 17:43:14 +00:00
cee3153f01
ar71xx: fix GPIO function handling on AR934x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29124 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 17:43:13 +00:00
2db6e74505
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29123 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 17:43:11 +00:00
de3ee69258
ar71xx: merge nand scan patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29122 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 17:43:10 +00:00
1fdbb4fcbd
ar71xx: fix a compiler warning
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29110 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 13:07:47 +00:00
33c5c80fa5
ar71xx: fix GPIO count for AR934x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29109 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 13:07:45 +00:00
54d08f41c9
ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29108 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:53 +00:00
546895e938
ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29107 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:51 +00:00
a921ab0827
ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29106 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:49 +00:00
ed73833a62
ar71xx: add an irq parameter for ar724x_pcibios_init
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29105 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:47 +00:00
6e87fe5dc5
ar71xx: remove hardwired interface parameters from mach-* files
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29103 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 07:38:09 +00:00
6f6b552473
ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29102 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 07:38:07 +00:00
75a8898840
ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29101 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 07:38:05 +00:00
fb3e9ac6b0
[brcm63xx] build images for Pirelli A226M ( #10409 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29045 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:22 +00:00
150feffb3b
[brcm63xx] register uart0 on DWV-S0 boards ( #10409 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29044 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:18 +00:00
dea0392387
[kernel] refresh 3.0 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29043 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:14 +00:00
9efe7cdbb7
[kernel] refresh 2.6.39 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29042 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:10 +00:00
f849b5a225
[brcm63xx] rename 456-board_DWV-S0_ehci.patch to 456-board_DWV-S0_fixes.patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29041 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:05 +00:00
351f04672c
[rdc] fix typo, load ip17xx switch module
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29039 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 18:41:26 +00:00
562bd7628c
ar71xx: enable has_gbit flag on AR724{0,1}
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29026 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 17:36:36 +00:00
81359fd675
ar71xx: fixup onboard PCIe chip registration on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29022 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 12:48:03 +00:00
23823d7a65
ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29021 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 12:48:01 +00:00
8e7450e3c2
ar71xx: ag71xx: add support for getting switch port link status
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29017 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:04 +00:00
25722074a3
ar71xx: remove mii_ctrl resources of the ethernet devices
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29016 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:03 +00:00
0e2b6d0d25
ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29015 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:01 +00:00
f0a3d94dff
ar71xx: ag71xx: remove unused mii_cfg related functions and defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29014 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:00 +00:00
51b1d36e03
ar71xx: set MII interface speed from the set_speed callbacks
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29013 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:59 +00:00
0839b18e6f
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29012 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:57 +00:00
7e0c585208
ar71xx: ag71xx: remove MII interface setup code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:56 +00:00
b28f1d9516
ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29010 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:54 +00:00
819f6df245
ar71xx: fix occasional kernel hangs during boot on AR934x
...
The patch taken from the linux-mips mailing list.
The Kernel hangs occasionally during boot after
"Calibrating delay loop..". This is caused by the
c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable
the timer and hang later. The false return happens
because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits
for the timer changes to propagate to the cp0 cause
register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb
instructions and can take as little as a few clock
ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not
working.
This fix uses up to a max number of cycle counter
ticks for the delay and uses back_to_back_c0_hazard()
instead of irq_disable_hazard() to handle the hazard
condition between cp0 writes and cp0 reads.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29009 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:52 +00:00
003cbe35e2
ar71xx: refresh kernel patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29008 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:51 +00:00
e30803b3df
linux: update 3.1 to 3.1.1
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29007 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 10:48:05 +00:00
b94c5c5031
lantiq: add uci-defaults code for handling leds
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29004 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:21 +00:00
508789fa68
lantiq: add /lib/lantiq.sh and make hotplug handlers use it
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29003 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:16 +00:00
39c1578720
lantiq: rename leds
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29002 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:12 +00:00
a7830ac4e2
lantiq: split compat headers out of bsp header patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29001 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:07 +00:00
4d22bffe5b
lantiq: adds hotplug handler for loading rt2x00 firmware
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29000 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:01 +00:00
e685dc989d
lantiq: adds hotplug handler for handling buttons and makes w303v work with it
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28999 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:39:56 +00:00
5d23a8d4b2
lantiq: cleanup default package selection
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28998 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:39:51 +00:00
a6a4c7a38a
lantiq: w303v has its rt2860 eep on the nor flash. tell compat-wireless how to use it
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28994 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 18:41:15 +00:00
be0c011b6e
kernel: ar8216: add support for the AR8236 switch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 14:09:52 +00:00
663c9eaaa1
kernel: ar8216: move port vlan setup into a separate function
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28992 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 14:09:50 +00:00
96e3c5d0b8
ar71xx: use the button for WPS control on the DB120
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28990 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:20 +00:00
0b8f0e8e22
ar71xx: register the second ethernet interface on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28989 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:19 +00:00
547b567ada
ar71xx: implement SoC specific phy interface setup
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28988 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:18 +00:00
2d684997e3
ar71xx: move phy interface setup into a separate function
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28987 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:16 +00:00
a680542669
ar71xx: register both MDIO bus on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28986 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:59 +00:00
aee435407b
ar71xx: add AR934X specific MDIO registration code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28985 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:56 +00:00
61471eaa03
ar71xx: add a secondary mdio bus
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28984 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:54 +00:00
008f0239fb
ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28983 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:50 +00:00
cf263134a7
ar71xx: add an id argument to ar71xx_add_device_mdio
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28982 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:48 +00:00
ff698943a3
ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsa
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28981 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:42 +00:00
c3d1b40766
ar71xx: add AR934x specific USB setup
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28980 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:20 +00:00
86beed68ca
ar71xx: register the first ethernet interface on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28979 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:18 +00:00
aa72cd1c08
ar71xx: allow to register ethernet interfaces for AR934X
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28978 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:17 +00:00
44a0cc9d1b
ar71xx: ag71xx: use fixed link parameters if the mii bus is not registered
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28977 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:16 +00:00
4faf62a121
ar71xx: add AR934X specific bootstrap and reset register bits
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28976 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:15 +00:00
ab5f1bf090
ar71xx: add diag support for the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28975 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:10 +00:00
856b67cb13
ar71xx: fix GPIO direction setup for AR934x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28974 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:09 +00:00
4bafa258d8
ar71xx: fix AR934X clock frequency calculation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28973 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:08 +00:00
3e6d0203d3
ar71xx: generate ubootenv from uci-defaults instead of providing defconfig
...
I noticed most of /etc/defconfig was replaced by /etc/uci-defaults, which is
indeed much nicer. So I moved over ubootenv from having a defconfig-entry to
also be generated from uci-defaults.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28971 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:04 +00:00
796b2be4f5
lantiq: improve falcon package selection
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28962 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11 21:59:11 +00:00
9b8ac845a1
lantiq: fix breakage introduced in 3.1 bump
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28961 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11 21:59:01 +00:00
d75509fe4d
base-files, target: assign name to system timeserver section, makes it easier to set servers on the cli
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28933 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10 12:16:41 +00:00
fba8b20978
target: linux: mtd: fix MTDREFRESH to an arbitrary high number
...
To make the ioctl number "stable", use an arbitrary high number to prevent
conflicts with new mtd ioctls that would push MTDREFRESH's number.
Also make mtd use the in-kernel mtd headers.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28893 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-09 21:16:36 +00:00
a31e4087d1
ar71xx: remove dead code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28851 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:33:20 +00:00
ebb2f0d93b
ar71xx: on ar7240, exclude ports from their own port vlan destination mask
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28850 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:33:15 +00:00
bb2e9e6c50
kernel: add a top level menuconfig option for enabling lockdep
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28848 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:32:57 +00:00
f324cde661
ar71xx: create TL-WA901ND network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28833 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:24 +00:00
7fa7bf413a
ar71xx: create ALL0258N network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28832 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:23 +00:00
ce845599cf
ar71xx: create NBG{460N,550N,550NH} network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28831 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:20 +00:00
0282878582
ar71xx: create WZR-HP-G300NH network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28830 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:17 +00:00
c5759b1fb1
ar71xx: create RB-493G network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28829 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:12 +00:00
e9214fa4f2
ar71xx: create TL-WR1043ND network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28828 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:11 +00:00
ffab58baa6
ar71xx: create WRT160NL network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28827 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:09 +00:00
0a1c3b4bb1
ar71xx: create PB92 network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28826 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:08 +00:00
bcb5dba8ba
ar71xx: create DIR-825-B1 network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28825 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:07 +00:00
cf735fe893
ar71xx: create TL-WR{841N-v1,941ND} network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28824 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:03 +00:00
71d946496e
ar71xx: create RB-450 network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28823 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:02 +00:00
d72b269a99
ar71xx: create RB-450G, RouterStation Pro network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28822 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:01 +00:00
986666a07d
ar71xx: create RB-433{,U} network config from uci defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28821 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:58 +00:00
3b52c3653c
ar71xx: create even more network configs from the uci-defaults script
...
Create the default network configuration dynamically for the
AR724x/AR9331 boards. Some other boards are using the same
configuration, so convert those as well.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28820 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:56 +00:00
5f5bb28ad3
ar71xx: create more network configs from the uci-defaults script
...
Create the default network configuration dynamically for the boards with
swapped eth0, eth1 interfaces.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28819 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:54 +00:00
2037793081
ar71xx: create a bunch of network configs from the uci-defaults script
...
Create the default network configuration dynamically for the boards with
a single ethernet interface.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28818 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:52 +00:00
23e7014185
ar71xx: create generic network config from an uci-defaults script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28817 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:51 +00:00
1c203e5ff8
ar71xx: remove AP81 defconfig, it is the same as the generic config
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28816 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:34:33 +00:00
c20327d5ff
ar71xx: change generated Buffalo firmware versions
...
With version 1.76 the upgrade may fail with newer Buffalo firmwares with
a message like this:
"You can not update the firmware because the firmware version is earlier
than 1.82. Please use 1.82 or later version for firmware update."
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28815 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:34:32 +00:00
63a2c4b8e1
[cns3xxx]: update 3.1 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28814 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:13:13 +00:00
022bf6081b
[generic/3.1]: update arm mach-types
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28813 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:12:26 +00:00
b949f4133d
ar71xx: enable sysupgrade on the WHR-G301N and WHR-HP-GN boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28812 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 20:25:00 +00:00
d2593ad142
ar71xx: wrap long lines in the upgrade script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28811 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 20:24:59 +00:00
5290614fac
ar71xx: fix WHR-HP-G300N firmware partition offset
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28810 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 20:24:57 +00:00
1517713d89
ar71xx: add default network configuration for the WHR-HP-GN
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28807 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 13:32:43 +00:00
f56da26294
ar71xx: build image for the Buffalo WHR-HP-GN
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28806 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:11 +00:00
10c12741af
ar71xx: add support for the Buffalo WHR-HP-GN board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28805 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:10 +00:00
ca96dda8d8
ar71xx: build image for the Buffalo WHR-G301N
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28804 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:08 +00:00
affce809d6
ar71xx: add support for the Buffalo WHR-G301N board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28803 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:07 +00:00
c94b4af3dc
ar71xx: fix WHR-HP-G300N image generation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28802 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:05 +00:00
d1bc81ae49
ar71xx: enable WHR-HP-G300N support in kernel config
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28801 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:04 +00:00
9e10ecd5d2
ar71xx: fix WHR-HP-G300N MTD partitions
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28800 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:03 +00:00
14fb2c27e2
omap24xx: Add cbus tahvo locking fix.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28767 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-05 16:10:18 +00:00
c7dc043776
omap24xx: Fix n810bm compilation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28766 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-05 16:01:53 +00:00
2149ed4fe1
kernel: swconfig: add a missing unlock in error path
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28753 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-04 14:38:31 +00:00
ca5eb9dd8f
add timeserver config to target specific system configs as well
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28750 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-04 12:53:35 +00:00
55e223b6e5
kernel: merge regression fixes for the netfilter patches to the 3.1 kernel patches (patch by tripolar)
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28734 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-03 20:02:31 +00:00
1bae736951
lantiq: remove obseleted folder. we use 3.1 now
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28728 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-03 16:33:27 +00:00
fc4b9802d7
lantiq: bump to 3.1
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28721 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-03 15:15:52 +00:00
8aedee89d2
ar71xx: add missing AR71XX_MACH_TL_WR741ND_V4
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28709 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 14:38:12 +00:00
561175c967
ar71xx: build image for the TL-WR741ND v4 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28708 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 11:20:55 +00:00
18d762e403
ar71xx: add initial support for the TL-WR741ND v4 board
...
The ethernet port LEDs are not working yet.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28706 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 11:20:52 +00:00
a8f9979c55
ar71xx: add AR933X GMAC register defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28705 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 11:20:50 +00:00
0ed6243ba7
ar71xx: combine LEDs setup in one file
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28704 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 11:20:49 +00:00
2fdf9ce8cb
ar71xx: unify LED names on Planex boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28703 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 11:20:47 +00:00
2c27f3365b
ar71xx: unify LED names on Buffalo boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28702 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 11:20:46 +00:00
f17abe1ff3
ar71xx: unify LED names on TP-Link boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28701 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 11:20:44 +00:00
bb4cf4ec13
ar71xx/all0258n: sysupgrade support
...
U-Boot on the ALL0258N needs offset, size and md5 for kernel and rootfs to be
stored in the U-Boot environment.
If the checksums don't match during boot, a failsafe-system is booted instead.
This patch adds a board-specific sysupgrade hack for the all0258n which
calculates and updates the checksums for the U-Boot environment.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28700 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 09:23:32 +00:00
4a1af8218a
ar71xx/all0258n: add default config
...
This adds default network and uboot-env settings for the ALL0258N.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28699 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 09:23:31 +00:00
28d91da06e
ar71xx: remove default network config of the mzk-w04nu board as well
...
It works with the generic config.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28695 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-01 09:23:25 +00:00
3ef0b9c188
ar71xx: remove LED setup of nonexistent interfaces on RB750
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28693 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-31 14:26:56 +00:00
7515085565
ar71xx: remove default network config of the wnr2000 board
...
It is the same as the generic configuration.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28692 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-31 14:26:51 +00:00
0aacaac439
[ramips] rt305x: Create factory image for Fonera 2.0n
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28689 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-31 09:23:44 +00:00
82bfa0bff0
omap24xx: Default to linux-3.1
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28687 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-30 22:42:00 +00:00
9fcc0aa95a
omap24xx: Fix n810 LCD initialization
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28685 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-30 20:31:45 +00:00
7c665bf99f
omap24xx: Fix n810 boot
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28683 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-30 18:46:45 +00:00
0cd7c7c114
ar71xx/sysupgrade: use $magic_long instead of $magic when comparing with a 32-bit value
...
Aparently $magic_long was meant here instead of $magic when comparing with
32-bit values.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28678 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-30 13:06:30 +00:00
bf711a224c
omap24xx: Refresh 3.1 config
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28677 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-29 22:52:44 +00:00
37ff2a430d
omap24xx: Refresh 3.1 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28676 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-29 22:52:07 +00:00
541b8d0d4b
Fix tusb patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28675 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-29 22:33:59 +00:00
902dada571
omap24xx: Fix MUSB compile
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28674 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-29 22:26:27 +00:00
b24c7757b8
omap24xx: Add n800 touchscreen and keypad drivers.
...
Thanks to Marat Radchenko.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28673 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-29 20:35:36 +00:00
f9cfd5e297
omap24xx: Add 3.1 patchset.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28672 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-29 19:02:50 +00:00
deb302d092
ar71xx: fix typos in image/Makefile
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28618 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-27 07:54:52 +00:00
ddc9918fc1
ar71xx: add initial support for the OpenMesh OM2P board
...
Based on a patch by Marek Lindner <marek@open-mesh.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28617 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-27 07:54:51 +00:00
8750c52ceb
ar71xx/all0258n: fix partition layout
...
A miscalculation in the original patch makes OpenWrt destroy the failsafe image.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28615 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-27 07:54:47 +00:00
93dc2abf47
Update my email address
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28603 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-26 14:54:26 +00:00
4e80f252de
x86: disable crashlog, ioremap of RAM does not work properly here
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28599 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-26 11:49:25 +00:00
dbebe488f6
ar71xx: create image for the WNDR3800
...
This adds support for the Netgear WNDR3800, it is almost the same as
the WNDR3700v2. It just has more RAM so the hd_id had to be adjusted.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28597 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-26 06:12:47 +00:00
163c5d5b6b
target: remove CONFIG_IDE_PROC_FS support as well
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28586 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-25 16:40:06 +00:00
05b0a7b54d
brcm47xx: revert accidentially added EARLY_PRINTK symbol from previous commit
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28585 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-25 16:19:52 +00:00
0a7950b452
target: globally disable BSD process accounting
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28584 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-25 16:18:36 +00:00
28f21bbb71
ramips: Support for NexAira BC2
...
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28571 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:36 +00:00
d0e52cf25f
ramips: fix switch-port assignment for HW550-3G
...
WAN is on swtich port 0 for Aztech HW550-3G.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28570 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:32 +00:00
32fd7022f9
ramips: combine led setup for all boards in one file
...
This removes unnecessary duplication and simplifies led setup for new
boards. It would be a one line change most likely.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28569 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:31 +00:00
249da9f193
ar71xx: build image for the Buffalo WHR-HP-G300N
...
Based on a patch by Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28568 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:29 +00:00
7344100219
ar71xx: Buffalo WHR-HP-G300N kernel support
...
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28567 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:26 +00:00
4ac887fba4
ar71xx: build image for the Allnet ALL0258N board
...
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28565 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:23 +00:00
5333794b36
ar71xx: add kernel support for the Allnet ALL0258N board
...
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28564 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:21 +00:00
ab0f50a421
ar71xx: don't override CONFIG_FSNOTIFY
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28563 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:49:18 +00:00
704be5a0f9
[ar71xx] base-files: make sure inittab-console-fixup returns with success ( #10275 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28562 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-24 21:35:43 +00:00
59bf9e97fa
[target] x86: allow VDI & VMDK images for all subtargets ( closes : #10255 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28518 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-22 13:09:15 +00:00
23b3d9ba74
linux: generic: refresh patches for 3.1-rc10
...
Hopefully the last one and identical to final.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28492 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-20 10:32:44 +00:00
b987bdd364
linux: ar71xx: add support for Mikrotik Routerboard RB493G
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28423 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-11 23:05:16 +00:00
2b7dfdc5ef
ar71xx: add a workaround for ar8316 not always driving the TA bit to low
...
AR8316 behind a GPIO bitbanged MDIO bus fails to drive the turnaround bit
to low despite returning a valid value. Ignore it and just use the
returned value anyway.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28422 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-10-11 23:05:13 +00:00
Gabor Juhos
Felix Fietkau
John Crispin
Jonas Gorski
Jo-Philipp Wich
Nicolas Thill
Florian Fainelli
Michael Büsch
Imre Kaloz
Vasilis Tsiligiannis