33c5c80fa5
ar71xx: fix GPIO count for AR934x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29109 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 13:07:45 +00:00
54d08f41c9
ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29108 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:53 +00:00
546895e938
ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29107 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:51 +00:00
a921ab0827
ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29106 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:49 +00:00
ed73833a62
ar71xx: add an irq parameter for ar724x_pcibios_init
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29105 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 11:49:47 +00:00
6e87fe5dc5
ar71xx: remove hardwired interface parameters from mach-* files
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29103 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 07:38:09 +00:00
6f6b552473
ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29102 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 07:38:07 +00:00
75a8898840
ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29101 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-14 07:38:05 +00:00
fb3e9ac6b0
[brcm63xx] build images for Pirelli A226M ( #10409 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29045 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:22 +00:00
150feffb3b
[brcm63xx] register uart0 on DWV-S0 boards ( #10409 )
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29044 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:18 +00:00
dea0392387
[kernel] refresh 3.0 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29043 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:14 +00:00
9efe7cdbb7
[kernel] refresh 2.6.39 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29042 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:10 +00:00
f849b5a225
[brcm63xx] rename 456-board_DWV-S0_ehci.patch to 456-board_DWV-S0_fixes.patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29041 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 19:19:05 +00:00
351f04672c
[rdc] fix typo, load ip17xx switch module
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29039 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 18:41:26 +00:00
562bd7628c
ar71xx: enable has_gbit flag on AR724{0,1}
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29026 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 17:36:36 +00:00
81359fd675
ar71xx: fixup onboard PCIe chip registration on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29022 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 12:48:03 +00:00
23823d7a65
ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29021 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 12:48:01 +00:00
8e7450e3c2
ar71xx: ag71xx: add support for getting switch port link status
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29017 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:04 +00:00
25722074a3
ar71xx: remove mii_ctrl resources of the ethernet devices
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29016 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:03 +00:00
0e2b6d0d25
ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29015 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:01 +00:00
f0a3d94dff
ar71xx: ag71xx: remove unused mii_cfg related functions and defines
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29014 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:27:00 +00:00
51b1d36e03
ar71xx: set MII interface speed from the set_speed callbacks
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29013 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:59 +00:00
0839b18e6f
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29012 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:57 +00:00
7e0c585208
ar71xx: ag71xx: remove MII interface setup code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:56 +00:00
b28f1d9516
ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29010 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:54 +00:00
819f6df245
ar71xx: fix occasional kernel hangs during boot on AR934x
...
The patch taken from the linux-mips mailing list.
The Kernel hangs occasionally during boot after
"Calibrating delay loop..". This is caused by the
c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable
the timer and hang later. The false return happens
because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits
for the timer changes to propagate to the cp0 cause
register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb
instructions and can take as little as a few clock
ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not
working.
This fix uses up to a max number of cycle counter
ticks for the delay and uses back_to_back_c0_hazard()
instead of irq_disable_hazard() to handle the hazard
condition between cp0 writes and cp0 reads.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29009 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:52 +00:00
003cbe35e2
ar71xx: refresh kernel patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29008 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 11:26:51 +00:00
e30803b3df
linux: update 3.1 to 3.1.1
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29007 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-13 10:48:05 +00:00
b94c5c5031
lantiq: add uci-defaults code for handling leds
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29004 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:21 +00:00
508789fa68
lantiq: add /lib/lantiq.sh and make hotplug handlers use it
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29003 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:16 +00:00
39c1578720
lantiq: rename leds
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29002 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:12 +00:00
a7830ac4e2
lantiq: split compat headers out of bsp header patch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29001 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:07 +00:00
4d22bffe5b
lantiq: adds hotplug handler for loading rt2x00 firmware
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29000 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:40:01 +00:00
e685dc989d
lantiq: adds hotplug handler for handling buttons and makes w303v work with it
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28999 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:39:56 +00:00
5d23a8d4b2
lantiq: cleanup default package selection
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28998 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 23:39:51 +00:00
a6a4c7a38a
lantiq: w303v has its rt2860 eep on the nor flash. tell compat-wireless how to use it
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28994 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 18:41:15 +00:00
be0c011b6e
kernel: ar8216: add support for the AR8236 switch
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28993 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 14:09:52 +00:00
663c9eaaa1
kernel: ar8216: move port vlan setup into a separate function
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28992 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 14:09:50 +00:00
96e3c5d0b8
ar71xx: use the button for WPS control on the DB120
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28990 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:20 +00:00
0b8f0e8e22
ar71xx: register the second ethernet interface on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28989 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:19 +00:00
547b567ada
ar71xx: implement SoC specific phy interface setup
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28988 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:18 +00:00
2d684997e3
ar71xx: move phy interface setup into a separate function
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28987 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:50:16 +00:00
a680542669
ar71xx: register both MDIO bus on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28986 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:59 +00:00
aee435407b
ar71xx: add AR934X specific MDIO registration code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28985 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:56 +00:00
61471eaa03
ar71xx: add a secondary mdio bus
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28984 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:54 +00:00
008f0239fb
ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28983 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:50 +00:00
cf263134a7
ar71xx: add an id argument to ar71xx_add_device_mdio
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28982 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:48 +00:00
ff698943a3
ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsa
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28981 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 12:09:42 +00:00
c3d1b40766
ar71xx: add AR934x specific USB setup
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28980 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:20 +00:00
86beed68ca
ar71xx: register the first ethernet interface on the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28979 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:18 +00:00
aa72cd1c08
ar71xx: allow to register ethernet interfaces for AR934X
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28978 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:17 +00:00
44a0cc9d1b
ar71xx: ag71xx: use fixed link parameters if the mii bus is not registered
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28977 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:16 +00:00
4faf62a121
ar71xx: add AR934X specific bootstrap and reset register bits
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28976 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:15 +00:00
ab5f1bf090
ar71xx: add diag support for the DB120 board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28975 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:10 +00:00
856b67cb13
ar71xx: fix GPIO direction setup for AR934x
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28974 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:09 +00:00
4bafa258d8
ar71xx: fix AR934X clock frequency calculation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28973 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:08 +00:00
3e6d0203d3
ar71xx: generate ubootenv from uci-defaults instead of providing defconfig
...
I noticed most of /etc/defconfig was replaced by /etc/uci-defaults, which is
indeed much nicer. So I moved over ubootenv from having a defconfig-entry to
also be generated from uci-defaults.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28971 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-12 10:54:04 +00:00
796b2be4f5
lantiq: improve falcon package selection
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28962 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11 21:59:11 +00:00
9b8ac845a1
lantiq: fix breakage introduced in 3.1 bump
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28961 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-11 21:59:01 +00:00
d75509fe4d
base-files, target: assign name to system timeserver section, makes it easier to set servers on the cli
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28933 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-10 12:16:41 +00:00
fba8b20978
target: linux: mtd: fix MTDREFRESH to an arbitrary high number
...
To make the ioctl number "stable", use an arbitrary high number to prevent
conflicts with new mtd ioctls that would push MTDREFRESH's number.
Also make mtd use the in-kernel mtd headers.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28893 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-09 21:16:36 +00:00
a31e4087d1
ar71xx: remove dead code
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28851 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:33:20 +00:00
ebb2f0d93b
ar71xx: on ar7240, exclude ports from their own port vlan destination mask
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28850 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:33:15 +00:00
bb2e9e6c50
kernel: add a top level menuconfig option for enabling lockdep
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28848 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-08 00:32:57 +00:00
f324cde661
ar71xx: create TL-WA901ND network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28833 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:24 +00:00
7fa7bf413a
ar71xx: create ALL0258N network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28832 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:23 +00:00
ce845599cf
ar71xx: create NBG{460N,550N,550NH} network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28831 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:20 +00:00
0282878582
ar71xx: create WZR-HP-G300NH network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28830 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:17 +00:00
c5759b1fb1
ar71xx: create RB-493G network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28829 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:12 +00:00
e9214fa4f2
ar71xx: create TL-WR1043ND network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28828 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:11 +00:00
ffab58baa6
ar71xx: create WRT160NL network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28827 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:09 +00:00
0a1c3b4bb1
ar71xx: create PB92 network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28826 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:08 +00:00
bcb5dba8ba
ar71xx: create DIR-825-B1 network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28825 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:07 +00:00
cf735fe893
ar71xx: create TL-WR{841N-v1,941ND} network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28824 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:03 +00:00
71d946496e
ar71xx: create RB-450 network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28823 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:02 +00:00
d72b269a99
ar71xx: create RB-450G, RouterStation Pro network config from uci-defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28822 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:44:01 +00:00
986666a07d
ar71xx: create RB-433{,U} network config from uci defaults
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28821 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:58 +00:00
3b52c3653c
ar71xx: create even more network configs from the uci-defaults script
...
Create the default network configuration dynamically for the
AR724x/AR9331 boards. Some other boards are using the same
configuration, so convert those as well.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28820 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:56 +00:00
5f5bb28ad3
ar71xx: create more network configs from the uci-defaults script
...
Create the default network configuration dynamically for the boards with
swapped eth0, eth1 interfaces.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28819 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:54 +00:00
2037793081
ar71xx: create a bunch of network configs from the uci-defaults script
...
Create the default network configuration dynamically for the boards with
a single ethernet interface.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28818 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:52 +00:00
23e7014185
ar71xx: create generic network config from an uci-defaults script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28817 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:43:51 +00:00
1c203e5ff8
ar71xx: remove AP81 defconfig, it is the same as the generic config
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28816 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:34:33 +00:00
c20327d5ff
ar71xx: change generated Buffalo firmware versions
...
With version 1.76 the upgrade may fail with newer Buffalo firmwares with
a message like this:
"You can not update the firmware because the firmware version is earlier
than 1.82. Please use 1.82 or later version for firmware update."
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28815 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:34:32 +00:00
63a2c4b8e1
[cns3xxx]: update 3.1 patches
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28814 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:13:13 +00:00
022bf6081b
[generic/3.1]: update arm mach-types
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28813 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 21:12:26 +00:00
b949f4133d
ar71xx: enable sysupgrade on the WHR-G301N and WHR-HP-GN boards
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28812 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 20:25:00 +00:00
d2593ad142
ar71xx: wrap long lines in the upgrade script
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28811 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 20:24:59 +00:00
5290614fac
ar71xx: fix WHR-HP-G300N firmware partition offset
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28810 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 20:24:57 +00:00
1517713d89
ar71xx: add default network configuration for the WHR-HP-GN
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28807 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 13:32:43 +00:00
f56da26294
ar71xx: build image for the Buffalo WHR-HP-GN
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28806 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:11 +00:00
10c12741af
ar71xx: add support for the Buffalo WHR-HP-GN board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28805 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:10 +00:00
ca96dda8d8
ar71xx: build image for the Buffalo WHR-G301N
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28804 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:08 +00:00
affce809d6
ar71xx: add support for the Buffalo WHR-G301N board
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28803 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:07 +00:00
c94b4af3dc
ar71xx: fix WHR-HP-G300N image generation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28802 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:05 +00:00
d1bc81ae49
ar71xx: enable WHR-HP-G300N support in kernel config
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28801 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:04 +00:00
9e10ecd5d2
ar71xx: fix WHR-HP-G300N MTD partitions
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28800 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-07 12:59:03 +00:00
14fb2c27e2
omap24xx: Add cbus tahvo locking fix.
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28767 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-05 16:10:18 +00:00
c7dc043776
omap24xx: Fix n810bm compilation
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28766 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-05 16:01:53 +00:00
2149ed4fe1
kernel: swconfig: add a missing unlock in error path
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28753 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-04 14:38:31 +00:00
ca5eb9dd8f
add timeserver config to target specific system configs as well
...
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28750 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-11-04 12:53:35 +00:00
Gabor Juhos
Florian Fainelli
Jonas Gorski
John Crispin
Jo-Philipp Wich
Felix Fietkau
Imre Kaloz
Michael Büsch