This sets 'enable_vlan' and thus uses 802.1q
VLANs, but without tagging on either interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44509 3c298f89-4303-0410-b956-a3cf2f4a3e73
Toggles the LA bit on the WAN interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44508 3c298f89-4303-0410-b956-a3cf2f4a3e73
The current pxa3xx_nand driver doesn't support sub-page writing,
so the VID header offset must be specified explicitly.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44455 3c298f89-4303-0410-b956-a3cf2f4a3e73
In order for the image to be built, some patches need to be ported to 3.19.
Add the relevant patches. Note that most of them (if not all) should be merged
in 3.20, removing the need to carry them on then.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44267 3c298f89-4303-0410-b956-a3cf2f4a3e73
All the boards but Mamba had wrong UBI options so far, making it impossible to
flash the built image on their respective storage medium.
Fix all of the supported boards in order to make the generated images useful.
Tested on a Mirabox, an Armada XP GP and an Openblocks AX3, and used the NAND
chip datasheet for the others.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44264 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some boards only come with a small NOR on it, where UBI isn't a good solution
because of its overhead.
Add a new subprofile for such boards, that rely on the mtd split framework
instead.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44263 3c298f89-4303-0410-b956-a3cf2f4a3e73
While we supported only the NAND so far, some boards use a large enough NOR,
where UBI is the only reasonable option. Create a new sub-profile template with
a different set of UBI options.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44262 3c298f89-4303-0410-b956-a3cf2f4a3e73
In order to support the various board NAND layout that we support, introduce a
sub-profile similar to the one used by ar71xx.
These subprofiles provide a default implementation for most of the building
functions, while allowing each sub-profile to override any of these operations
in order to have a more specific behaviour, like Mamba expects for example.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44261 3c298f89-4303-0410-b956-a3cf2f4a3e73
We're going to need the MTD split related options for our NOR support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44259 3c298f89-4303-0410-b956-a3cf2f4a3e73
The mvebu image makefile define something almost identical to the generic
implementation found in include/image.mk.
Switch to this implementation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43969 3c298f89-4303-0410-b956-a3cf2f4a3e73
The mvebu image Makefile directly calls the padjffs2 utility, while there's an
generic make function to do just that. Switch to it
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43968 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a 3.14.x backport of:
"mvneta: Fix TSO and checksum for non-acceleration vlan traffic"
Upstream commits:
817dbfa5d1bc276a72c1a577310382008e8aca0a
2d39d120781a5770573dc6ed672a5a562f541aea
Fixes vlan tagging on SoC interfaces for the WRT1900AC. Useful
when using mvsw6171 driver.
Signed-off-by: Mark Milburn <mark.a.milburn@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43781 3c298f89-4303-0410-b956-a3cf2f4a3e73
final images, so store them in KDIR instead.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43778 3c298f89-4303-0410-b956-a3cf2f4a3e73
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43715 3c298f89-4303-0410-b956-a3cf2f4a3e73
This option was removed in upstream commit 8357041.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43607 3c298f89-4303-0410-b956-a3cf2f4a3e73
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43047 3c298f89-4303-0410-b956-a3cf2f4a3e73
Targets were build tested and patches are refreshed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42463 3c298f89-4303-0410-b956-a3cf2f4a3e73
Imre Kaloz
Luka Perkov
Jo-Philipp Wich
John Crispin
Felix Fietkau