Commit Graph

7 Commits (436f87b02911529846347178dccef21fda28c005)

Author SHA1 Message Date
Hauke Mehrtens f6d2f50c9b brcm47xx: add new led and button support
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39252 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-12 18:55:25 +00:00
Hauke Mehrtens 5627388168 brcm47xx: b44: This updates the phylib patches to the version send upstream
This uses a fixed phy instead of a dummy one.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39166 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-26 23:27:52 +00:00
Hauke Mehrtens b5fc88a75d brcm47xx: deactivate mips wait instruction only for BCM4706
The wait instruction is only broken on the BCM4706 and not on the other 
similar SoCs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38979 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-01 18:05:08 +00:00
Hauke Mehrtens e4c5404c56 brcm47xx: update early printk patches
Early printk was disabled because it caused hangs on some devices, the 
old patches were using the CFE console now we use the normal serial 
console, it is at a constant address.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38309 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06 23:55:35 +00:00
Hauke Mehrtens cd2b261f51 brcm47xx: update board detection patches
Add patches like they are currently in the mainline mips tree and add 
some more pending patches for board detection.

* Now the board name is shown under machine in /proc/cpuinfo.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38308 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-06 23:51:24 +00:00
Hauke Mehrtens 81cf14367f brcm47xx: Add support for Huawei E970
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.

The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.

It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.

Tested and works:  3G wan,  wlan+LED,  VLAN config,  failsafe using reset
button,   image to be used for upgrade from OEM firmware's web interface

Link to the wiki page I've created:  <http://wiki.openwrt.org/toh/huawei/e970>

Issue:

* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
  reset during kernel decompress.

Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38011 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-09-16 21:09:10 +00:00
Hauke Mehrtens d631e85a63 brcm47xx: add initial support for kernel 3.10
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37287 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14 13:44:45 +00:00