Reorder BuildPackage calls, as libubox needs to come first for ABI
version handling to work
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39722 3c298f89-4303-0410-b956-a3cf2f4a3e73
If a package directly depends on another package that recently changed
its ABI version, it will be cleaned up and rebuilt (assuming quilt is
not used).
This helps with packages that have no stable ABI, e.g. libubox, ubus,
etc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39720 3c298f89-4303-0410-b956-a3cf2f4a3e73
We did not start the PHY when an external phy was in use. Without this
patch the driver uses half duplex mode and the switch uses full duplex
mode, which causes problems.
Thank you fback for spotting this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39719 3c298f89-4303-0410-b956-a3cf2f4a3e73
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39703 3c298f89-4303-0410-b956-a3cf2f4a3e73
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39702 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39700 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used for the Mikrotik boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39697 3c298f89-4303-0410-b956-a3cf2f4a3e73
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39696 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is a backported patch for the gianfar ethernet driver
used in TPLink 4900 v1. It is supposed to fix the error which
show up in dmesg with:
NETDEV WATCHDOG: eth0 (fsl-gianfar): transmit queue xy timed out
Full upstream patch is at: http://patchwork.ozlabs.org/patch/271242
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39692 3c298f89-4303-0410-b956-a3cf2f4a3e73
Set usbh ports to 2 to fix#15007.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39681 3c298f89-4303-0410-b956-a3cf2f4a3e73
Don't only fix up the fallback board, but also all three variants.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39680 3c298f89-4303-0410-b956-a3cf2f4a3e73
Only netboot tested, so no images or now.
GbE ports are only working in FE mode, and leds do not work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39679 3c298f89-4303-0410-b956-a3cf2f4a3e73
Completely untested except for booting from network; wan port
only works in 10/HD, lan1 only in 100/FD.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39678 3c298f89-4303-0410-b956-a3cf2f4a3e73
BCM63168 has 6 ports (3 FE PHY, 1 GE PHY, two RGMII) and BCM63268
has two additional RGMII ports, making it 8.
Fix this by checking the chip variant and applying an appropriate
limit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39677 3c298f89-4303-0410-b956-a3cf2f4a3e73
Felix Fietkau
Hauke Mehrtens
Gabor Juhos
Nicolas Thill
Jonas Gorski