This is taken care of by the tulip driver accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34563 3c298f89-4303-0410-b956-a3cf2f4a3e73
We can now use the mainline tulip driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34559 3c298f89-4303-0410-b956-a3cf2f4a3e73
Isolate the PCI specific parts and group them under CONFIG_TULIP_PCI
CONFIG_TULIP_PLATFORM can be enabled for a platform style Tulip driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34557 3c298f89-4303-0410-b956-a3cf2f4a3e73
At some point we should make the ADM5120 PCI controller driver a real
platform driver and share that one between the two targets.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34553 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is not the place to expose it and duplicates code reading the
system frequency.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34551 3c298f89-4303-0410-b956-a3cf2f4a3e73
These patches are not specific to bcm47xx and will be used on other
platforms as well.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34501 3c298f89-4303-0410-b956-a3cf2f4a3e73
function. This removes those from the dwc_otg driver and removes the patch
that comments out the linkage of udc-core so that the dwc_otg driver can
co-exist happily with other USB Device Controllers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34475 3c298f89-4303-0410-b956-a3cf2f4a3e73
Back in the days when we could not override /etc/inittab, it made a lot
of sense to rename ttyAM to ttyS since this was the only supported
serial device(s), we can now just put in an appropriate /etc/inittab file
now.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34469 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch from #12533.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34445 3c298f89-4303-0410-b956-a3cf2f4a3e73
This target is unused, does not support any off the shelf hardware and
has been a maintenance burden for quite some time now.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34430 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patches about to go into net-next.git
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34410 3c298f89-4303-0410-b956-a3cf2f4a3e73
The work has been backported from openwrt-dreambox with
some modifications & code cleanup.
* updated config-3.3
* updated config-3.6
* renamed rt-n13 to rt-n13u
* fixed mach-rt-n13u.c
[juhosg: move user-space support and image generation into separate
patches]
Signed-off-by: Amit Mendapara <mendapara.amit@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34405 3c298f89-4303-0410-b956-a3cf2f4a3e73
The removed symbols are present in the generic configuration.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34404 3c298f89-4303-0410-b956-a3cf2f4a3e73
The removed symbols are present in the generic configuration.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34403 3c298f89-4303-0410-b956-a3cf2f4a3e73
Found in the AudioCodes Tulip AC494 ATA.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34395 3c298f89-4303-0410-b956-a3cf2f4a3e73
We don't support disabling the clock, but this is actually what it would do.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34394 3c298f89-4303-0410-b956-a3cf2f4a3e73
The general practice is to use the general SoC compatible string in both the
DTS and the board specific .c file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34393 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Kconfig identifier to enable debugging in the driver was different from the
actually used one. Fix that.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34332 3c298f89-4303-0410-b956-a3cf2f4a3e73
Commit 7c8edac25f23c4fc14239fdc293caa1317649944 introduced new machine and
Makefile changes to build images for this target. However, without the userspace
bits a ramips machine can't use wifi as the necessary "eeprom" data is to be
extracted by a hotplug script; also, sysupgrade support and default led
configuration are missing.
An IRC user reported these changes allowed him to use wifi on his hardware.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34331 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ASUS WL-520gU and some other similar Asus devices have a BCM5354
running at 200MHZ and not at 240 which is the default for this SoC.
This fixes#4083.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34325 3c298f89-4303-0410-b956-a3cf2f4a3e73
In the old configuration the SoC issued a reboot if the watchdog was
killed also if it was kill with TERM and not KILL.
This will fix#11724.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34324 3c298f89-4303-0410-b956-a3cf2f4a3e73
This watchdog driver should work with SoC having a PMU.
This fixes#11720.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34323 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for defining rt2x00 eeprom data.
This eeprom data can be extracted from flash or loaded directly from a firmware file.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34322 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some boards need specifying LED pin in order to get it working.
For example, in board HW556 (Huawei HG556a) "led_pin" must be "2".
By default led_pin is "0", so dsl_274xb_rev_f is changed to "-1".
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34321 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Accept transfers without bits_per_word set.
* Work around the inability of the hardware of keeping CS asserted.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34320 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also override the pll_1000 value. Without these settings
ethernet suffers from packet loss.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34316 3c298f89-4303-0410-b956-a3cf2f4a3e73
Musl is an alternative C-library, see http://www.musl-libc.org for more infos.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34314 3c298f89-4303-0410-b956-a3cf2f4a3e73
The ar8216_mib_{capture,flush} functions are similar.
Move the common code into a helper and use that from
the original functions.
This change also fixes a lockdep warning in
ar8216_mib_flush.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34297 3c298f89-4303-0410-b956-a3cf2f4a3e73
swconfig does not compile with 3.7 because
struct netlink_notify->pid has been renamed to
struct netlink_notify->portid
and
struct genl_info->snd_pid has been renamed to
struct genl_info->snd_portid
Use the new names and add compatibility patches
to 3.3 and 3.6.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34288 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also add a WARN_ON to 'ar8216_mib_fetch_port_stat'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34283 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also add compatibility patches for the currently
supported kernels.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34279 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also add compatibility patches for the currently
supported kernels.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34278 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is a dead code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34276 3c298f89-4303-0410-b956-a3cf2f4a3e73
The new lzma compressed elf kernel image fits into
that, even on devices with large page NAND chips.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34274 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will be used on the RB4xx/RB7xx/RB2011 boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34272 3c298f89-4303-0410-b956-a3cf2f4a3e73
This allows to load the resulting image directly
from RouterBOOT.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34271 3c298f89-4303-0410-b956-a3cf2f4a3e73
[juhosg: move ramips specific stuff into a followup patch]
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34269 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reverts commit r34230, as it is causing build failures:
make[3] -C package/mtd compile
imagetag.c:35:32: fatal error: linux/bcm963xx_tag.h: No such file or directory
compilation terminated.
make[4]: *** [imagetag.o] Error 1
Any patches modifying exported kernel headers need to reside in generic
as toolchain/kernel-headers only applies generic patches.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34255 3c298f89-4303-0410-b956-a3cf2f4a3e73
Florian Fainelli
Felix Fietkau
Hauke Mehrtens
Gabor Juhos
Jo-Philipp Wich
Jonas Gorski
John Crispin
Imre Kaloz