WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31910 3c298f89-4303-0410-b956-a3cf2f4a3e73
moves the linux partition, removes the config partition and the
buttons settings have small adjustments.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31909 3c298f89-4303-0410-b956-a3cf2f4a3e73
The VLAN mapping on the ARV4520PW board is the following:
port on Router: | VLAN in software:
LAN 1 | 3
LAN 2 | 2
LAN 3 | 1
LAN 4 | 0
DSL | 4
So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31391 3c298f89-4303-0410-b956-a3cf2f4a3e73
Implements the ARV752DPW architecture in mach-arv.c
Signed-off-by: Christian Rustmeier <rustmeier@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31206 3c298f89-4303-0410-b956-a3cf2f4a3e73
A power-enable toggle gpio is not available, it is always on and protected with a resettable fuse.
Signed-off-by: Pieter Voorthuijsen<p.voorthuijsen at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31205 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also remove a duplicate patch from lantiq (already in generic).
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31158 3c298f89-4303-0410-b956-a3cf2f4a3e73
Turns out it triggers on some AR71xx devices where no swapping should be done.
Enable endian check for the lantiq target.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@31084 3c298f89-4303-0410-b956-a3cf2f4a3e73
Needed for using external rootfs on usb sticks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30940 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30537 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Luka Perkov
Gabor Juhos
Felix Fietkau
Jonas Gorski
Mirko Vogt