This patch builds on the previous three to streamline support for the
Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44032 3c298f89-4303-0410-b956-a3cf2f4a3e73
It seems the call to ltq_get_eth_mac() disappeared at some point. This
patch puts it where it currently most makes sense.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44031 3c298f89-4303-0410-b956-a3cf2f4a3e73
Somewhere in the conversion of the MIPS architecture code to Device Tree
usage, there's been a failure to keep the separate variables holding the
kernel command line reconciled between the tree and the bootloader. This
patch restores previous functionality that broke.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44030 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently this initscript fails if the macaddr has any leading zeroes.
This patch corrects the problem.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44029 3c298f89-4303-0410-b956-a3cf2f4a3e73
The swconfig get_link attribute (at least) on AR8327/AR8337 doesn't
consider the autonegotiated flow control.
AR8327/AR8337 provide the info about autonegotiated rx/tx flow control
in bits 10 and 11 of the port status register.
Use these values to display info about autonegotiated rx/tx flow
control as part of the get_link attribute.
Successfully tested on TL-WDR4900 (AR8327 rev.4) and
TL-WDR4300 (AR8327 rev.2).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44023 3c298f89-4303-0410-b956-a3cf2f4a3e73
AR8327/AR8337 allow to read the result of EEE autonegotiation.
If EEE is autonegotiated between the link partners, display
this as part of the swconfig get_link attribute.
eee100: 100MBit EEE supported by both link partners
eee1000: 1GBit EEE supported by both link partners
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44022 3c298f89-4303-0410-b956-a3cf2f4a3e73
Users reported network issues with AR8327 which turned out to be caused
by EEE not working correctly with certain link partners (ticket 14597).
The workaround was to disable EEE on all ports (changeset 41577).
The issue was with certain link partners only, therefore this patch
allows to control usage of EEE per port via swconfig.
Still the default is to initially disable EEE on all ports.
Successfully tested on a TL-WDR4900 (AR8327 rev.4)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44021 3c298f89-4303-0410-b956-a3cf2f4a3e73
(used if the boot loader wants a different loadaddr/entry)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44014 3c298f89-4303-0410-b956-a3cf2f4a3e73
fixes newer ECO versions and a hang on reboot bug
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44008 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44001 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add profile and userspace for P2812HNUF1/3, switch from UBI_GLUEBI to UBI_BLOCK
Signed-off-by: Sylwester Petela <sscapi@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43987 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add device tree for P2812HNUF1 and P2812HNUF3.
Signed-off-by: Sylwester Petela <sscapi@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43986 3c298f89-4303-0410-b956-a3cf2f4a3e73
i2c pins are wired to wps a reset button
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43985 3c298f89-4303-0410-b956-a3cf2f4a3e73
use new helper function to generate default led configuration
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43984 3c298f89-4303-0410-b956-a3cf2f4a3e73
The only reason this patch was helping was moving bcma init *after*
of_serial init. It was a bit of luck because both drivers use
device_initcall.
It isn't really a correct way to provide early logging.
Now we have earlyprintk support in bcm53xx we can drop this patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43981 3c298f89-4303-0410-b956-a3cf2f4a3e73
Malta ramdisk images are no longer copied to output due to a recent change.
This change reimplements copying of ramdisk images for Malta builds.
Signed-off-by: Eric Schultz <eschultz@prplfoundation.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43970 3c298f89-4303-0410-b956-a3cf2f4a3e73
The mvebu image makefile define something almost identical to the generic
implementation found in include/image.mk.
Switch to this implementation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43969 3c298f89-4303-0410-b956-a3cf2f4a3e73
The mvebu image Makefile directly calls the padjffs2 utility, while there's an
generic make function to do just that. Switch to it
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43968 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Felix Fietkau
Rafał Miłecki
Imre Kaloz