Currently port 6 is shown as up 10MBit/half in LUCI and swconfig.
Reason is that all bits in the port 6 config are zero.
This means that also the aneg flag is not set and in this case
ar8216_read_port_link hardcodes the link to be up.
This is no real problem but a little annoying.
To fix this initialize port 6 with the aneg bit enabled.
This causes ar8216_read_port_link to evaluate the link status bit which is
always zero for port 6 as no PHY is connected to this port.
And it doesn't hurt as port 6 isn't connected to anything on TL-WDR4900.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45749 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix an upstream regression on 3.18+ that causes rt305x based devices
to hang on boot.
Fixes#19715.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45747 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change set enables frequency scaling on ipq806x, which speeds-up
the CPU and allows it to achieve its max frequency.
These patches are cherry-picked & backported from the following location:
*130-132: linux-next
*133-143: LKML - https://lkml.org/lkml/2015/3/21/15
*144: derived from other qcom similar dts
*145: derived from https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-3.14/drivers/cpufreq/cpufreq-krait.c
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45730 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45729 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch cherry-picked from the following location:
https://chromium-review.googlesource.com/#/c/269931/
Disable the i2c device on gsbi4 and mark gsbi4_h and gsbi4_qup clks as
unused. If they are enabled, clock framework will turn them off at end
of probe. On ipq806x by design gsbi4_qup, gsbi4_h clks and i2c on gsbi4
are meant for RPM usage. So turning them off in kernel is incorrect.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45728 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.
Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45726 3c298f89-4303-0410-b956-a3cf2f4a3e73
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)
Signed-off-by: Matteo Panella <m.panella@level28.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45725 3c298f89-4303-0410-b956-a3cf2f4a3e73
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45724 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45722 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45718 3c298f89-4303-0410-b956-a3cf2f4a3e73
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45717 3c298f89-4303-0410-b956-a3cf2f4a3e73
There is also a OHCI controller, activate it for USB 1.1 support.
This should close#19601.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45716 3c298f89-4303-0410-b956-a3cf2f4a3e73
3.18.13 introduced a bunch of new errata, enable them to be on the
safe side.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45715 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45709 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the Huawei HG655b.
Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45708 3c298f89-4303-0410-b956-a3cf2f4a3e73
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
patching file net/ipv6/ip6_output.c
Hunk #1 FAILED at 886.
1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
patching file net/ipv6/route.c
Hunk #1 succeeded at 2247 (offset 2 lines).
Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)
This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45705 3c298f89-4303-0410-b956-a3cf2f4a3e73
This device seems to have switch port 7 connected to the CPU:
vlan1ports=1 2 3 5 7*
vlan2ports=0 7u
it should be handled by eth1 and NVRAM seems to confirm that (no
et0macaddr entry, existing et1macaddr & et1phyaddr entries).
One of the remaining ports (4/8?) may be connected to the Quantenna SoC.
Original firmware boot log contains following messages:
(0x00,0x5d)Port 5 States Override: 0xfb
(0x00,0x5f)Port 7 States Override: 0xfb
(0x00,0x0e)Port 8 States Override: 0x0a
(why does it force port 5 state?!)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45692 3c298f89-4303-0410-b956-a3cf2f4a3e73
It has 3 Ethernet interfaces, each of them connected to separated switch
port. Default NVRAM uses switch port 8 as CPU which is connected to the
3rd interface (eth2).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45681 3c298f89-4303-0410-b956-a3cf2f4a3e73
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45676 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.
[ 2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.970000] 2 netgear-fw partitions found on MTD device firmware
[ 2.970000] 0x000000070000-0x000000188440 : "kernel"
[ 2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs"
The patch removes the rather useless warning message.
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45669 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)
We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45663 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.
It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45662 3c298f89-4303-0410-b956-a3cf2f4a3e73
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.
On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.
As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45661 3c298f89-4303-0410-b956-a3cf2f4a3e73
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45658 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45647 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45643 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45640 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45639 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45638 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45637 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45636 3c298f89-4303-0410-b956-a3cf2f4a3e73
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45635 3c298f89-4303-0410-b956-a3cf2f4a3e73
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45634 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861
I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
2) must init GMAC0 before GMAC1
That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.
An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.
2) Possible consequence of no longer explicitly setting ethernet duplex/speed.
Review: With this patch, my ethernet and wireless works.
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45633 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45632 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45631 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45630 3c298f89-4303-0410-b956-a3cf2f4a3e73
It has been broken since the new ath10k firmware introduced in r44656.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45624 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also refresh one patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45601 3c298f89-4303-0410-b956-a3cf2f4a3e73
This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45599 3c298f89-4303-0410-b956-a3cf2f4a3e73
This will make these files much more maintainable.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45597 3c298f89-4303-0410-b956-a3cf2f4a3e73
Moved board to the right magic case.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45588 3c298f89-4303-0410-b956-a3cf2f4a3e73
INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.
So just disable it for everyone.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45584 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was a remnant of an old version.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45583 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some devices have unsorted ports which may lead to broken config.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45575 3c298f89-4303-0410-b956-a3cf2f4a3e73
I still need to test following patch before backporting:
bgmac: leave interrupts disabled as long as there is work to do
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45571 3c298f89-4303-0410-b956-a3cf2f4a3e73
Linux 4.0 was released on 2014-04-12
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45559 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix the led naming and gpios.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45558 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hopefully the last missing board.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45557 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the XW version of the Rocket M series devices
manufactured by Ubiquiti, based on the Atheros AR9342 SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45553 3c298f89-4303-0410-b956-a3cf2f4a3e73
Felix Fietkau
Jonas Gorski
John Crispin
Hauke Mehrtens
Steven Barth
Imre Kaloz
Rafał Miłecki
Luka Perkov
Florian Fainelli