|
|
|
|
@ -1,284 +1,96 @@
|
|
|
|
|
--- a/nl80211.h
|
|
|
|
|
+++ b/nl80211.h
|
|
|
|
|
@@ -156,21 +156,23 @@
|
|
|
|
|
* @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
|
|
|
|
|
* or %NL80211_ATTR_MAC.
|
|
|
|
|
@@ -565,6 +565,14 @@
|
|
|
|
|
* %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ with
|
|
|
|
|
* %NL80211_ATTR_WIPHY_CHANNEL_TYPE.
|
|
|
|
|
*
|
|
|
|
|
- * @NL80211_CMD_GET_BEACON: retrieve beacon information (returned in a
|
|
|
|
|
- * %NL80222_CMD_NEW_BEACON message)
|
|
|
|
|
- * @NL80211_CMD_SET_BEACON: set the beacon on an access point interface
|
|
|
|
|
- * using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD,
|
|
|
|
|
- * %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes.
|
|
|
|
|
- * Following attributes are provided for drivers that generate full Beacon
|
|
|
|
|
- * and Probe Response frames internally: %NL80211_ATTR_SSID,
|
|
|
|
|
+ * @NL80211_CMD_GET_BEACON: (not used)
|
|
|
|
|
+ * @NL80211_CMD_SET_BEACON: change the beacon on an access point interface
|
|
|
|
|
+ * using the %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL
|
|
|
|
|
+ * attributes. For drivers that generate the beacon and probe responses
|
|
|
|
|
+ * internally, the following attributes must be provided: %NL80211_ATTR_IE,
|
|
|
|
|
+ * %NL80211_ATTR_IE_PROBE_RESP and %NL80211_ATTR_IE_ASSOC_RESP.
|
|
|
|
|
+ * @NL80211_CMD_START_AP: Start AP operation on an AP interface, parameters
|
|
|
|
|
+ * are like for %NL80211_CMD_SET_BEACON, and additionally parameters that
|
|
|
|
|
+ * do not change are used, these include %NL80211_ATTR_BEACON_INTERVAL,
|
|
|
|
|
+ * %NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID,
|
|
|
|
|
* %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE,
|
|
|
|
|
* %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS,
|
|
|
|
|
* %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
|
|
|
|
|
- * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_IE, %NL80211_ATTR_IE_PROBE_RESP,
|
|
|
|
|
- * %NL80211_ATTR_IE_ASSOC_RESP.
|
|
|
|
|
- * @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface,
|
|
|
|
|
- * parameters are like for %NL80211_CMD_SET_BEACON.
|
|
|
|
|
- * @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it
|
|
|
|
|
+ * %NL80211_ATTR_AUTH_TYPE and %NL80211_ATTR_INACTIVITY_TIMEOUT.
|
|
|
|
|
+ * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
|
|
|
|
|
+ * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
|
|
|
|
|
+ * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
|
|
|
|
|
*
|
|
|
|
|
* @NL80211_CMD_GET_STATION: Get station attributes for station identified by
|
|
|
|
|
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
|
|
|
|
|
@@ -367,6 +369,11 @@
|
|
|
|
|
* %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
|
|
|
|
|
* %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
|
|
|
|
|
* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
|
|
|
|
|
+ * Background scan period can optionally be
|
|
|
|
|
+ * specified in %NL80211_ATTR_BG_SCAN_PERIOD,
|
|
|
|
|
+ * if not specified default background scan configuration
|
|
|
|
|
+ * in driver is used and if period value is 0, bg scan will be disabled.
|
|
|
|
|
+ * This attribute is ignored if driver does not support roam scan.
|
|
|
|
|
* It is also sent as an event, with the BSSID and response IEs when the
|
|
|
|
|
* connection is established or failed to be established. This can be
|
|
|
|
|
* determined by the STATUS_CODE attribute.
|
|
|
|
|
@@ -541,6 +548,11 @@
|
|
|
|
|
* @NL80211_CMD_SET_NOACK_MAP: sets a bitmap for the individual TIDs whether
|
|
|
|
|
* No Acknowledgement Policy should be applied.
|
|
|
|
|
*
|
|
|
|
|
+ * @NL80211_CMD_CH_SWITCH_NOTIFY: An AP or GO may decide to switch channels
|
|
|
|
|
+ * independently of the userspace SME, send this event indicating
|
|
|
|
|
+ * %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ with
|
|
|
|
|
+ * %NL80211_ATTR_WIPHY_CHANNEL_TYPE.
|
|
|
|
|
+ * @NL80211_CMD_START_P2P_DEVICE: Start the given P2P Device, identified by
|
|
|
|
|
+ * its %NL80211_ATTR_WDEV identifier. It must have been created with
|
|
|
|
|
+ * %NL80211_CMD_NEW_INTERFACE previously. After it has been started, the
|
|
|
|
|
+ * P2P Device can be used for P2P operations, e.g. remain-on-channel and
|
|
|
|
|
+ * public action frame TX.
|
|
|
|
|
+ * @NL80211_CMD_STOP_P2P_DEVICE: Stop the given P2P Device, identified by
|
|
|
|
|
+ * its %NL80211_ATTR_WDEV identifier.
|
|
|
|
|
+ *
|
|
|
|
|
* @NL80211_CMD_MAX: highest used command number
|
|
|
|
|
* @__NL80211_CMD_AFTER_LAST: internal use
|
|
|
|
|
*/
|
|
|
|
|
@@ -565,8 +577,10 @@ enum nl80211_commands {
|
|
|
|
|
@@ -708,6 +716,9 @@ enum nl80211_commands {
|
|
|
|
|
|
|
|
|
|
NL80211_CMD_GET_BEACON,
|
|
|
|
|
NL80211_CMD_SET_BEACON,
|
|
|
|
|
- NL80211_CMD_NEW_BEACON,
|
|
|
|
|
- NL80211_CMD_DEL_BEACON,
|
|
|
|
|
+ NL80211_CMD_START_AP,
|
|
|
|
|
+ NL80211_CMD_NEW_BEACON = NL80211_CMD_START_AP,
|
|
|
|
|
+ NL80211_CMD_STOP_AP,
|
|
|
|
|
+ NL80211_CMD_DEL_BEACON = NL80211_CMD_STOP_AP,
|
|
|
|
|
NL80211_CMD_CH_SWITCH_NOTIFY,
|
|
|
|
|
|
|
|
|
|
NL80211_CMD_GET_STATION,
|
|
|
|
|
NL80211_CMD_SET_STATION,
|
|
|
|
|
@@ -680,6 +694,8 @@ enum nl80211_commands {
|
|
|
|
|
|
|
|
|
|
NL80211_CMD_SET_NOACK_MAP,
|
|
|
|
|
|
|
|
|
|
+ NL80211_CMD_CH_SWITCH_NOTIFY,
|
|
|
|
|
+ NL80211_CMD_START_P2P_DEVICE,
|
|
|
|
|
+ NL80211_CMD_STOP_P2P_DEVICE,
|
|
|
|
|
+
|
|
|
|
|
/* add new commands above here */
|
|
|
|
|
|
|
|
|
|
/* used to define NL80211_CMD_MAX below */
|
|
|
|
|
@@ -1193,6 +1209,19 @@ enum nl80211_commands {
|
|
|
|
|
* @NL80211_ATTR_NOACK_MAP: This u16 bitmap contains the No Ack Policy of
|
|
|
|
|
* up to 16 TIDs.
|
|
|
|
|
*
|
|
|
|
|
+ * @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be
|
|
|
|
|
+ * used by the drivers which has MLME in firmware and does not have support
|
|
|
|
|
+ * to report per station tx/rx activity to free up the staion entry from
|
|
|
|
|
+ * the list. This needs to be used when the driver advertises the
|
|
|
|
|
+ * capability to timeout the stations.
|
|
|
|
|
+ *
|
|
|
|
|
+ * @NL80211_ATTR_RX_SIGNAL_DBM: signal strength in dBm (as a 32-bit int);
|
|
|
|
|
+ * this attribute is (depending on the driver capabilities) added to
|
|
|
|
|
+ * received frames indicated with %NL80211_CMD_FRAME.
|
|
|
|
|
+ *
|
|
|
|
|
+ * @NL80211_ATTR_BG_SCAN_PERIOD: Background scan period in seconds
|
|
|
|
|
+ * or 0 to disable background scan.
|
|
|
|
|
+ *
|
|
|
|
|
* @NL80211_ATTR_MAX: highest attribute number currently defined
|
|
|
|
|
* @__NL80211_ATTR_AFTER_LAST: internal use
|
|
|
|
|
*/
|
|
|
|
|
@@ -1438,6 +1467,12 @@ enum nl80211_attrs {
|
|
|
|
|
@@ -1506,6 +1517,8 @@ enum nl80211_attrs {
|
|
|
|
|
|
|
|
|
|
NL80211_ATTR_NOACK_MAP,
|
|
|
|
|
NL80211_ATTR_USER_REG_HINT_TYPE,
|
|
|
|
|
|
|
|
|
|
+ NL80211_ATTR_INACTIVITY_TIMEOUT,
|
|
|
|
|
+
|
|
|
|
|
+ NL80211_ATTR_RX_SIGNAL_DBM,
|
|
|
|
|
+
|
|
|
|
|
+ NL80211_ATTR_BG_SCAN_PERIOD,
|
|
|
|
|
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
|
|
|
|
|
+
|
|
|
|
|
/* add attributes here, update the policy in nl80211.c */
|
|
|
|
|
|
|
|
|
|
__NL80211_ATTR_AFTER_LAST,
|
|
|
|
|
@@ -1475,6 +1510,7 @@ enum nl80211_attrs {
|
|
|
|
|
#define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
|
|
|
|
|
@@ -1575,6 +1588,10 @@ enum nl80211_attrs {
|
|
|
|
|
* @NL80211_IFTYPE_MESH_POINT: mesh point
|
|
|
|
|
* @NL80211_IFTYPE_P2P_CLIENT: P2P client
|
|
|
|
|
* @NL80211_IFTYPE_P2P_GO: P2P group owner
|
|
|
|
|
+ * @NL80211_IFTYPE_P2P_DEVICE: P2P device interface type, this is not a netdev
|
|
|
|
|
+ * and therefore can't be created in the normal ways, use the
|
|
|
|
|
+ * %NL80211_CMD_START_P2P_DEVICE and %NL80211_CMD_STOP_P2P_DEVICE
|
|
|
|
|
+ * commands to create and destroy one
|
|
|
|
|
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
|
|
|
|
|
* @NUM_NL80211_IFTYPES: number of defined interface types
|
|
|
|
|
*
|
|
|
|
|
@@ -1593,6 +1610,7 @@ enum nl80211_iftype {
|
|
|
|
|
NL80211_IFTYPE_MESH_POINT,
|
|
|
|
|
NL80211_IFTYPE_P2P_CLIENT,
|
|
|
|
|
NL80211_IFTYPE_P2P_GO,
|
|
|
|
|
+ NL80211_IFTYPE_P2P_DEVICE,
|
|
|
|
|
|
|
|
|
|
#define NL80211_MAX_SUPP_RATES 32
|
|
|
|
|
+#define NL80211_MAX_SUPP_HT_RATES 77
|
|
|
|
|
#define NL80211_MAX_SUPP_REG_RULES 32
|
|
|
|
|
#define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0
|
|
|
|
|
#define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
|
|
|
|
|
@@ -1536,7 +1572,11 @@ enum nl80211_iftype {
|
|
|
|
|
* @NL80211_STA_FLAG_WME: station is WME/QoS capable
|
|
|
|
|
* @NL80211_STA_FLAG_MFP: station uses management frame protection
|
|
|
|
|
* @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
|
|
|
|
|
- * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer
|
|
|
|
|
+ * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should
|
|
|
|
|
+ * only be used in managed mode (even in the flags mask). Note that the
|
|
|
|
|
+ * flag can't be changed, it is only valid while adding a station, and
|
|
|
|
|
+ * attempts to change it will silently be ignored (rather than rejected
|
|
|
|
|
+ * as errors.)
|
|
|
|
|
* @NL80211_STA_FLAG_MAX: highest station flag number currently defined
|
|
|
|
|
* @__NL80211_STA_FLAG_AFTER_LAST: internal use
|
|
|
|
|
*/
|
|
|
|
|
@@ -1651,6 +1691,10 @@ enum nl80211_sta_bss_param {
|
|
|
|
|
* containing info as possible, see &enum nl80211_sta_bss_param
|
|
|
|
|
* @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
|
|
|
|
|
/* keep last */
|
|
|
|
|
NUM_NL80211_IFTYPES,
|
|
|
|
|
@@ -1744,6 +1762,8 @@ enum nl80211_sta_bss_param {
|
|
|
|
|
* @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update.
|
|
|
|
|
+ * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32)
|
|
|
|
|
+ * @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64)
|
|
|
|
|
* @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32)
|
|
|
|
|
* @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64)
|
|
|
|
|
+ * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
|
|
|
|
|
+ * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
|
|
|
|
|
* @__NL80211_STA_INFO_AFTER_LAST: internal
|
|
|
|
|
* @NL80211_STA_INFO_MAX: highest possible station info attribute
|
|
|
|
|
*/
|
|
|
|
|
@@ -1673,6 +1717,10 @@ enum nl80211_sta_info {
|
|
|
|
|
NL80211_STA_INFO_BSS_PARAM,
|
|
|
|
|
NL80211_STA_INFO_CONNECTED_TIME,
|
|
|
|
|
@@ -1768,6 +1788,8 @@ enum nl80211_sta_info {
|
|
|
|
|
NL80211_STA_INFO_STA_FLAGS,
|
|
|
|
|
+ NL80211_STA_INFO_BEACON_LOSS,
|
|
|
|
|
+ NL80211_STA_INFO_T_OFFSET,
|
|
|
|
|
NL80211_STA_INFO_BEACON_LOSS,
|
|
|
|
|
NL80211_STA_INFO_T_OFFSET,
|
|
|
|
|
+ NL80211_STA_INFO_CHAIN_SIGNAL,
|
|
|
|
|
+ NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
|
|
|
|
|
|
|
|
|
|
/* keep last */
|
|
|
|
|
__NL80211_STA_INFO_AFTER_LAST,
|
|
|
|
|
@@ -2098,8 +2146,18 @@ enum nl80211_mntr_flags {
|
|
|
|
|
* TUs) during which a mesh STA can send only one Action frame containing a
|
|
|
|
|
* PERR element.
|
|
|
|
|
*
|
|
|
|
|
+ * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding
|
|
|
|
|
+ * or forwarding entity (default is TRUE - forwarding entity)
|
|
|
|
|
+ *
|
|
|
|
|
+ * @NL80211_MESHCONF_RSSI_THRESHOLD: RSSI threshold in dBm. This specifies the
|
|
|
|
|
+ * threshold for average signal strength of candidate station to establish
|
|
|
|
|
+ * a peer link.
|
|
|
|
|
+ *
|
|
|
|
|
* @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
|
|
|
|
|
*
|
|
|
|
|
+ * @NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR: maximum number of neighbors
|
|
|
|
|
+ * to synchronize to for 11s default synchronization method (see 11C.12.2.2)
|
|
|
|
|
+ *
|
|
|
|
|
* @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
|
|
|
|
|
*/
|
|
|
|
|
enum nl80211_meshconf_params {
|
|
|
|
|
@@ -2122,6 +2180,9 @@ enum nl80211_meshconf_params {
|
|
|
|
|
NL80211_MESHCONF_HWMP_RANN_INTERVAL,
|
|
|
|
|
NL80211_MESHCONF_GATE_ANNOUNCEMENTS,
|
|
|
|
|
NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL,
|
|
|
|
|
+ NL80211_MESHCONF_FORWARDING,
|
|
|
|
|
+ NL80211_MESHCONF_RSSI_THRESHOLD,
|
|
|
|
|
+ NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR,
|
|
|
|
|
|
|
|
|
|
/* keep last */
|
|
|
|
|
__NL80211_MESHCONF_ATTR_AFTER_LAST,
|
|
|
|
|
@@ -2161,6 +2222,11 @@ enum nl80211_meshconf_params {
|
|
|
|
|
* complete (unsecured) mesh peering without the need of a userspace daemon.
|
|
|
|
|
*
|
|
|
|
|
* @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
|
|
|
|
|
+ *
|
|
|
|
|
+ * @NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC: Enable this option to use a
|
|
|
|
|
+ * vendor specific synchronization method or disable it to use the default
|
|
|
|
|
+ * neighbor offset synchronization
|
|
|
|
|
+ *
|
|
|
|
|
* @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
|
|
|
|
|
*/
|
|
|
|
|
enum nl80211_mesh_setup_params {
|
|
|
|
|
@@ -2170,6 +2236,7 @@ enum nl80211_mesh_setup_params {
|
|
|
|
|
NL80211_MESH_SETUP_IE,
|
|
|
|
|
NL80211_MESH_SETUP_USERSPACE_AUTH,
|
|
|
|
|
NL80211_MESH_SETUP_USERSPACE_AMPE,
|
|
|
|
|
+ NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC,
|
|
|
|
|
|
|
|
|
|
/* keep last */
|
|
|
|
|
__NL80211_MESH_SETUP_ATTR_AFTER_LAST,
|
|
|
|
|
@@ -2179,7 +2246,7 @@ enum nl80211_mesh_setup_params {
|
|
|
|
|
/**
|
|
|
|
|
* enum nl80211_txq_attr - TX queue parameter attributes
|
|
|
|
|
* @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
|
|
|
|
|
- * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*)
|
|
|
|
|
+ * @NL80211_TXQ_ATTR_AC: AC identifier (NL80211_AC_*)
|
|
|
|
|
* @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning
|
|
|
|
|
* disabled
|
|
|
|
|
* @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form
|
|
|
|
|
@@ -2192,7 +2259,7 @@ enum nl80211_mesh_setup_params {
|
|
|
|
|
*/
|
|
|
|
|
enum nl80211_txq_attr {
|
|
|
|
|
__NL80211_TXQ_ATTR_INVALID,
|
|
|
|
|
- NL80211_TXQ_ATTR_QUEUE,
|
|
|
|
|
+ NL80211_TXQ_ATTR_AC,
|
|
|
|
|
NL80211_TXQ_ATTR_TXOP,
|
|
|
|
|
NL80211_TXQ_ATTR_CWMIN,
|
|
|
|
|
NL80211_TXQ_ATTR_CWMAX,
|
|
|
|
|
@@ -2203,13 +2270,21 @@ enum nl80211_txq_attr {
|
|
|
|
|
NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
-enum nl80211_txq_q {
|
|
|
|
|
- NL80211_TXQ_Q_VO,
|
|
|
|
|
- NL80211_TXQ_Q_VI,
|
|
|
|
|
- NL80211_TXQ_Q_BE,
|
|
|
|
|
- NL80211_TXQ_Q_BK
|
|
|
|
|
+enum nl80211_ac {
|
|
|
|
|
+ NL80211_AC_VO,
|
|
|
|
|
+ NL80211_AC_VI,
|
|
|
|
|
+ NL80211_AC_BE,
|
|
|
|
|
+ NL80211_AC_BK,
|
|
|
|
|
+ NL80211_NUM_ACS
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
+/* backward compat */
|
|
|
|
|
+#define NL80211_TXQ_ATTR_QUEUE NL80211_TXQ_ATTR_AC
|
|
|
|
|
+#define NL80211_TXQ_Q_VO NL80211_AC_VO
|
|
|
|
|
+#define NL80211_TXQ_Q_VI NL80211_AC_VI
|
|
|
|
|
+#define NL80211_TXQ_Q_BE NL80211_AC_BE
|
|
|
|
|
+#define NL80211_TXQ_Q_BK NL80211_AC_BK
|
|
|
|
|
+
|
|
|
|
|
enum nl80211_channel_type {
|
|
|
|
|
NL80211_CHAN_NO_HT,
|
|
|
|
|
NL80211_CHAN_HT20,
|
|
|
|
|
@@ -2395,12 +2470,15 @@ enum nl80211_key_attributes {
|
|
|
|
|
* in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with
|
|
|
|
|
* 1 = 500 kbps) but without the IE length restriction (at most
|
|
|
|
|
* %NL80211_MAX_SUPP_RATES in a single array).
|
|
|
|
|
+ * @NL80211_TXRATE_MCS: HT (MCS) rates allowed for TX rate selection
|
|
|
|
|
+ * in an array of MCS numbers.
|
|
|
|
|
* @__NL80211_TXRATE_AFTER_LAST: internal
|
|
|
|
|
* @NL80211_TXRATE_MAX: highest TX rate attribute
|
|
|
|
|
*/
|
|
|
|
|
enum nl80211_tx_rate_attributes {
|
|
|
|
|
__NL80211_TXRATE_INVALID,
|
|
|
|
|
NL80211_TXRATE_LEGACY,
|
|
|
|
|
+ NL80211_TXRATE_MCS,
|
|
|
|
|
|
|
|
|
|
/* keep last */
|
|
|
|
|
__NL80211_TXRATE_AFTER_LAST,
|
|
|
|
|
@@ -2786,10 +2864,13 @@ enum nl80211_ap_sme_features {
|
|
|
|
|
* TX status to the socket error queue when requested with the
|
|
|
|
|
* socket option.
|
|
|
|
|
* @NL80211_FEATURE_HT_IBSS: This driver supports IBSS with HT datarates.
|
|
|
|
|
+ * @NL80211_FEATURE_INACTIVITY_TIMER: This driver takes care of freeing up
|
|
|
|
|
+ * the connected inactive stations in AP mode.
|
|
|
|
|
@@ -2994,12 +3016,18 @@ enum nl80211_ap_sme_features {
|
|
|
|
|
* @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested
|
|
|
|
|
* to work properly to suppport receiving regulatory hints from
|
|
|
|
|
* cellular base stations.
|
|
|
|
|
+ * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: If this is set, an active
|
|
|
|
|
+ * P2P Device (%NL80211_IFTYPE_P2P_DEVICE) requires its own channel
|
|
|
|
|
+ * in the interface combinations, even when it's only used for scan
|
|
|
|
|
+ * and remain-on-channel. This could be due to, for example, the
|
|
|
|
|
+ * remain-on-channel implementation requiring a channel context.
|
|
|
|
|
*/
|
|
|
|
|
enum nl80211_feature_flags {
|
|
|
|
|
NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
|
|
|
|
|
NL80211_FEATURE_HT_IBSS = 1 << 1,
|
|
|
|
|
- NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
|
|
|
|
|
- NL80211_FEATURE_HT_IBSS = 1 << 1,
|
|
|
|
|
- NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
|
|
|
|
|
- NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3,
|
|
|
|
|
+ NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
|
|
|
|
|
+ NL80211_FEATURE_HT_IBSS = 1 << 1,
|
|
|
|
|
+ NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
|
|
|
|
|
+ NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3,
|
|
|
|
|
+ NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4,
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
|
Felix Fietkau