ralink: add support for na930

Signed-off-by: John Crispin <blogic@openwrt.org>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39611 3c298f89-4303-0410-b956-a3cf2f4a3e73

target/linux/ramips/base-files/etc/diag.sh

@@ -161,6 +161,9 @@ get_status_led() {
 	f7c027)
 		status_led="belkin:orange:status"
 		;;
+	na930)
+		status_led="na930:blue:power"
+		;;
 	esac
 }
 

target/linux/ramips/base-files/etc/uci-defaults/01_leds

@@ -115,6 +115,9 @@ case $board in
 	mzk-w300nh2)
 		set_wifi_led "mzkw300nh2:amber:wlan"
 		;;
+	na930)
+		set_usb_led "na930:blue:status"
+		;;
 	nw718)
 		set_usb_led "nw718:amber:usb"
 		;;

target/linux/ramips/base-files/etc/uci-defaults/02_network

@@ -146,6 +146,7 @@ ramips_setup_interfaces()
 		;;
 
 	d105 | \
+	na930 | \
 	omni-emb-hpm|\
 	wli-tx4-ag300n)
 		ucidef_set_interface_lan "eth0"

target/linux/ramips/base-files/lib/ramips.sh

@@ -280,6 +280,9 @@ ramips_board_detect() {
 	*"V22SG")
 		name="v22sg"
 		;;
+	*"Sercomm NA930")
+		name="na930"
+		;;
 	*)
 		name="generic"
 		;;

target/linux/ramips/dts/NA930.dts

@@ -0,0 +1,164 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+	compatible = "ralink,mt7620a-eval-board", "ralink,mt7620a-soc";
+	model = "Sercomm NA930";
+
+	chosen {
+		bootargs = "console=ttyS1,57600";
+	};
+
+	pinctrl {
+		state_default: pinctrl0 {
+			gpio {
+				ralink,group = "i2c", "rgmii2", "spi", "ephy";
+				ralink,function = "gpio";
+			};
+			uartf_gpio {
+				ralink,group = "uartf";
+				ralink,function = "gpio uartf";
+			};
+		};
+	};
+
+	palmbus@10000000 {
+		uart@500 {
+			status = "okay";
+		};
+
+		gpio@638 {
+			status = "okay";
+		};
+
+		gpio@660 {
+			status = "okay";
+		};
+	};
+
+	nand {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "mtk,mt7620-nand";
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x20000>;
+			read-only;
+		};
+		partition@200000 {
+			label = "factory";
+			reg = <0x200000 0x40000>;
+			read-only;
+		};
+		partition@240000 {
+			label = "Config";
+			reg = <0x240000 0x400000>;
+			read-only;
+		};
+		partition@640000 {
+			label = "firmware";
+			reg = <0x640000 0x1400000>;
+		};
+	};
+
+	ethernet@10100000 {
+		status = "okay";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&rgmii1_pins &mdio_pins>;
+
+		ralink,port-map = "llllw";
+
+		port@4 {
+			status = "okay";
+			phy-handle = <&phy4>;
+			phy-mode = "rgmii";
+		};
+
+		port@5 {
+			status = "okay";
+			phy-handle = <&phy5>;
+			phy-mode = "rgmii";
+		};
+
+		mdio-bus {
+			status = "okay";
+
+			phy4: ethernet-phy@4 {
+				reg = <4>;
+				phy-mode = "rgmii";
+			};
+
+			phy5: ethernet-phy@5 {
+				reg = <5>;
+				phy-mode = "rgmii";
+			};
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+		reset {
+			label = "reset";
+			gpios = <&gpio0 11 1>;
+			linux,code = <0x198>;
+		};
+		zwave {
+			label = "zwave";
+			gpios = <&gpio0 12 1>;
+			linux,code = <0x100>;
+		};
+		wps {
+			label = "wps";
+			gpios = <&gpio0 14 1>;
+			linux,code = <0x211>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		zwave {
+			label = "na930:blue:zwave";
+			gpios = <&gpio2 0 1>;
+		};
+		status {
+			label = "na930:blue:status";
+			gpios = <&gpio2 26 1>;
+		};
+		service {
+			label = "na930:blue:service";
+			gpios = <&gpio2 28 1>;
+		};
+		power {
+			label = "na930:blue:power";
+			gpios = <&gpio2 29 1>;
+		};
+	};
+
+	gpio_export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		telit {
+			gpio-export,name = "telit";
+			gpio-export,output = <1>;
+			gpios = <&gpio0 13 0>;
+		};
+	};
+
+	gsw@10110000 {
+		ralink,port4 = "gmac";
+	};
+
+	ehci@101c0000 {
+		status = "okay";
+	};
+
+	ohci@101c1000 {
+		status = "okay";
+	};
+};

target/linux/ramips/image/Makefile

@@ -666,6 +666,8 @@ Image/Build/Profile/WHR300HP2=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-300
 Image/Build/Profile/WHR600D=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-600d,WHR-600D,$(whr_300hp2_mtd_size))
 dlink810l_mtd_size=6881280
 Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
+na930_mtd_size=20971520
+Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
 
 ifeq ($(SUBTARGET),mt7620a)
 define Image/Build/Profile/Default
@@ -677,6 +679,7 @@ define Image/Build/Profile/Default
 	$(call Image/Build/Profile/DIR-810L,$(1))
 	$(call Image/Build/Profile/WHR300HP2,$(1))
 	$(call Image/Build/Profile/WHR600D,$(1))
+	$(call Image/Build/Profile/NA930,$(1))
 endef
 endif
 

target/linux/ramips/mt7620a/config-3.10

@@ -6,6 +6,7 @@ CONFIG_ARCH_HIBERNATION_POSSIBLE=y
 CONFIG_ARCH_REQUIRE_GPIOLIB=y
 CONFIG_ARCH_SUSPEND_POSSIBLE=y
 CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_AT803X_PHY=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_CEVT_R4K=y
 CONFIG_CLKDEV_LOOKUP=y
@@ -78,11 +79,13 @@ CONFIG_HW_HAS_PCI=y
 CONFIG_HW_RANDOM=m
 CONFIG_HZ_PERIODIC=y
 CONFIG_IMAGE_CMDLINE_HACK=y
+CONFIG_INET_LRO=y
 CONFIG_INITRAMFS_SOURCE=""
 CONFIG_IRQCHIP=y
 CONFIG_IRQ_CPU=y
 CONFIG_IRQ_DOMAIN=y
 CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_INTC=y
 CONFIG_IRQ_WORK=y
 CONFIG_M25PXX_USE_FAST_READ=y
 CONFIG_MDIO_BOARDINFO=y