ralink: add support for na930
Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39611 3c298f89-4303-0410-b956-a3cf2f4a3e73master
John Crispin
parent
d6515b152d
commit
36cfff4072
|
|
@ -160,7 +160,10 @@ get_status_led() {
|
|||
;;
|
||||
f7c027)
|
||||
status_led="belkin:orange:status"
|
||||
;;
|
||||
;;
|
||||
na930)
|
||||
status_led="na930:blue:power"
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
|
|
|
|||
|
|
@ -115,6 +115,9 @@ case $board in
|
|||
mzk-w300nh2)
|
||||
set_wifi_led "mzkw300nh2:amber:wlan"
|
||||
;;
|
||||
na930)
|
||||
set_usb_led "na930:blue:status"
|
||||
;;
|
||||
nw718)
|
||||
set_usb_led "nw718:amber:usb"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -146,6 +146,7 @@ ramips_setup_interfaces()
|
|||
;;
|
||||
|
||||
d105 | \
|
||||
na930 | \
|
||||
omni-emb-hpm|\
|
||||
wli-tx4-ag300n)
|
||||
ucidef_set_interface_lan "eth0"
|
||||
|
|
|
|||
|
|
@ -280,6 +280,9 @@ ramips_board_detect() {
|
|||
*"V22SG")
|
||||
name="v22sg"
|
||||
;;
|
||||
*"Sercomm NA930")
|
||||
name="na930"
|
||||
;;
|
||||
*)
|
||||
name="generic"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -0,0 +1,164 @@
|
|||
/dts-v1/;
|
||||
|
||||
/include/ "mt7620a.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "ralink,mt7620a-eval-board", "ralink,mt7620a-soc";
|
||||
model = "Sercomm NA930";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS1,57600";
|
||||
};
|
||||
|
||||
pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "i2c", "rgmii2", "spi", "ephy";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
uartf_gpio {
|
||||
ralink,group = "uartf";
|
||||
ralink,function = "gpio uartf";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
palmbus@10000000 {
|
||||
uart@500 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
gpio@638 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
gpio@660 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
nand {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "mtk,mt7620-nand";
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
partition@200000 {
|
||||
label = "factory";
|
||||
reg = <0x200000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@240000 {
|
||||
label = "Config";
|
||||
reg = <0x240000 0x400000>;
|
||||
read-only;
|
||||
};
|
||||
partition@640000 {
|
||||
label = "firmware";
|
||||
reg = <0x640000 0x1400000>;
|
||||
};
|
||||
};
|
||||
|
||||
ethernet@10100000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
|
||||
|
||||
ralink,port-map = "llllw";
|
||||
|
||||
port@4 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy4>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
port@5 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy5>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
mdio-bus {
|
||||
status = "okay";
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
phy5: ethernet-phy@5 {
|
||||
reg = <5>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
poll-interval = <20>;
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 11 1>;
|
||||
linux,code = <0x198>;
|
||||
};
|
||||
zwave {
|
||||
label = "zwave";
|
||||
gpios = <&gpio0 12 1>;
|
||||
linux,code = <0x100>;
|
||||
};
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio0 14 1>;
|
||||
linux,code = <0x211>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
zwave {
|
||||
label = "na930:blue:zwave";
|
||||
gpios = <&gpio2 0 1>;
|
||||
};
|
||||
status {
|
||||
label = "na930:blue:status";
|
||||
gpios = <&gpio2 26 1>;
|
||||
};
|
||||
service {
|
||||
label = "na930:blue:service";
|
||||
gpios = <&gpio2 28 1>;
|
||||
};
|
||||
power {
|
||||
label = "na930:blue:power";
|
||||
gpios = <&gpio2 29 1>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
telit {
|
||||
gpio-export,name = "telit";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio0 13 0>;
|
||||
};
|
||||
};
|
||||
|
||||
gsw@10110000 {
|
||||
ralink,port4 = "gmac";
|
||||
};
|
||||
|
||||
ehci@101c0000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ohci@101c1000 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
|
@ -666,6 +666,8 @@ Image/Build/Profile/WHR300HP2=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-300
|
|||
Image/Build/Profile/WHR600D=$(call BuildFirmware/CustomFlash/$(1),$(1),whr-600d,WHR-600D,$(whr_300hp2_mtd_size))
|
||||
dlink810l_mtd_size=6881280
|
||||
Image/Build/Profile/DIR-810L=$(call BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
|
||||
na930_mtd_size=20971520
|
||||
Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
|
||||
|
||||
ifeq ($(SUBTARGET),mt7620a)
|
||||
define Image/Build/Profile/Default
|
||||
|
|
@ -677,6 +679,7 @@ define Image/Build/Profile/Default
|
|||
$(call Image/Build/Profile/DIR-810L,$(1))
|
||||
$(call Image/Build/Profile/WHR300HP2,$(1))
|
||||
$(call Image/Build/Profile/WHR600D,$(1))
|
||||
$(call Image/Build/Profile/NA930,$(1))
|
||||
endef
|
||||
endif
|
||||
|
||||
|
|
|
|||
|
|
@ -6,6 +6,7 @@ CONFIG_ARCH_HIBERNATION_POSSIBLE=y
|
|||
CONFIG_ARCH_REQUIRE_GPIOLIB=y
|
||||
CONFIG_ARCH_SUSPEND_POSSIBLE=y
|
||||
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
|
||||
CONFIG_AT803X_PHY=y
|
||||
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
|
||||
CONFIG_CEVT_R4K=y
|
||||
CONFIG_CLKDEV_LOOKUP=y
|
||||
|
|
@ -78,11 +79,13 @@ CONFIG_HW_HAS_PCI=y
|
|||
CONFIG_HW_RANDOM=m
|
||||
CONFIG_HZ_PERIODIC=y
|
||||
CONFIG_IMAGE_CMDLINE_HACK=y
|
||||
CONFIG_INET_LRO=y
|
||||
CONFIG_INITRAMFS_SOURCE=""
|
||||
CONFIG_IRQCHIP=y
|
||||
CONFIG_IRQ_CPU=y
|
||||
CONFIG_IRQ_DOMAIN=y
|
||||
CONFIG_IRQ_FORCED_THREADING=y
|
||||
CONFIG_IRQ_INTC=y
|
||||
CONFIG_IRQ_WORK=y
|
||||
CONFIG_M25PXX_USE_FAST_READ=y
|
||||
CONFIG_MDIO_BOARDINFO=y
|
||||
|
|
|
|||
Loading…
Reference in New Issue