ramips: Add userspace support for the Edimax BR-6475nD

The rt2x00 wifi driver may still need updating to
function with this device.

Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39298 3c298f89-4303-0410-b956-a3cf2f4a3e73

target/linux/ramips/base-files/etc/diag.sh

@@ -21,7 +21,7 @@ get_status_led() {
 	br6524n)
 		status_led="edimax:blue:power"
 		;;
-	br6425)
+	br6425 | br-6475nd)
 		status_led="edimax:green:power"
 		;;
 	d105)

target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom

@@ -66,6 +66,7 @@ case "$FIRMWARE" in
 	awm002-evb | \
 	bc2 | \
 	br6425 | \
+	br-6475nd | \
 	broadway | \
 	br6524n | \
 	carambola | \

target/linux/ramips/base-files/etc/uci-defaults/01_leds

@@ -47,6 +47,9 @@ case $board in
 	br6425)
 		set_wifi_led "edimax:orange:wlan"
 		;;
+	br-6475nd)
+		set_wifi_led "edimax:amber:wlan"
+		;;
 	broadway)
 		set_usb_led "red:diskmounted"
 		set_wifi_led "red:wps_active"

target/linux/ramips/base-files/etc/uci-defaults/02_network

@@ -65,6 +65,13 @@ ramips_setup_interfaces()
 		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
 		;;
 
+	br-6475nd)
+		ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+		ucidef_add_switch "switch0" "1" "1"
+		ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 9t"
+		ucidef_add_switch_vlan "switch0" "2" "0 9t"
+		;;
+
 	asl26555)
 		ucidef_set_interface_lan "eth0.1"
 		ucidef_add_switch "switch0" "1" "1"
@@ -166,6 +173,11 @@ ramips_setup_macs()
 		wan_mac=$(macaddr_add "$lan_mac" 1)
 		;;
 
+	br-6475nd)
+		lan_mac=$(mtd_get_mac_binary devdata 13)
+		wan_mac=$(mtd_get_mac_binary devdata 7)
+		;;
+
 	w306r-v20)
 		wan_mac=$(macaddr_add "$lan_mac" 5)
 		;;

target/linux/ramips/base-files/lib/preinit/06_set_iface_mac

@@ -39,6 +39,10 @@ preinit_set_mac_address() {
 		mac=$(macaddr_setbit_la "$mac")
 		ifconfig eth0 hw ether $mac 2>/dev/null
 		;;
+	br-6475nd)
+		mac=$(mtd_get_mac_binary devdata 13)
+		ifconfig eth0 hw ether $mac 2>/dev/null
+		;;
 	asl26555 |\
 	dir-300-b1 |\
 	dir-300-b2 |\

target/linux/ramips/base-files/lib/ramips.sh

@@ -109,6 +109,9 @@ ramips_board_detect() {
 	*"ESR-9753")
 		name="esr-9753"
 		;;
+	*"Edimax BR-6475nD")
+		name="br-6475nd"
+		;;
 	*"F7C027")
 		name="f7c027"
 		;;

target/linux/ramips/base-files/lib/upgrade/platform.sh

@@ -100,6 +100,13 @@ platform_check_image() {
 		}
 		return 0
 		;;
+	br-6475nd)
+		[ "$magic" != "43535953" ] && {
+			echo "Invalid image type."
+			return 1
+		}
+		return 0
+		;;
 	esac
 
 	echo "Sysupgrade is not yet supported on $board."