wifipineapple-openwrt/target/linux/brcm47xx/patches-2.6.28/250-ohci-ssb-usb2.patch

73 lines
2.3 KiB
Diff
Raw Normal View History

--- a/drivers/usb/host/ohci-ssb.c
+++ b/drivers/usb/host/ohci-ssb.c
@@ -106,10 +106,59 @@ static int ssb_ohci_attach(struct ssb_de
int err = -ENOMEM;
u32 tmp, flags = 0;
- if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV)
+ /*
+ * THE FOLLOWING COMMENTS PRESERVED FROM GPL SOURCE RELEASE
+ *
+ * The USB core requires a special bit to be set during core
+ * reset to enable host (OHCI) mode. Resetting the SB core in
+ * pcibios_enable_device() is a hack for compatibility with
+ * vanilla usb-ohci so that it does not have to know about
+ * SB. A driver that wants to use the USB core in device mode
+ * should know about SB and should reset the bit back to 0
+ * after calling pcibios_enable_device().
+ */
+
+ if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
flags |= SSB_OHCI_TMSLOW_HOSTMODE;
+ ssb_device_enable(dev, flags);
+ }
+
+ /*
+ * USB 2.0 special considerations:
+ *
+ * 1. Since the core supports both OHCI and EHCI functions, it must
+ * only be reset once.
+ *
+ * 2. In addition to the standard SB reset sequence, the Host Control
+ * Register must be programmed to bring the USB core and various
+ * phy components out of reset.
+ */
+
+ else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
+#warning FIX ME need test for core being up & exit
+ ssb_device_enable(dev, 0);
+ ssb_write32(dev, 0x200, 0x7ff);
+ udelay(1);
+ if (dev->id.revision == 1) { // bug in rev 1
+
+ /* Change Flush control reg */
+ tmp = ssb_read32(dev, 0x400);
+ tmp &= ~8;
+ ssb_write32(dev, 0x400, tmp);
+ tmp = ssb_read32(dev, 0x400);
+ printk("USB20H fcr: 0x%0x\n", tmp);
+
+ /* Change Shim control reg */
+ tmp = ssb_read32(dev, 0x304);
+ tmp &= ~0x100;
+ ssb_write32(dev, 0x304, tmp);
+ tmp = ssb_read32(dev, 0x304);
+ printk("USB20H shim: 0x%0x\n", tmp);
+ }
+ }
+ else
+ ssb_device_enable(dev, 0);
- ssb_device_enable(dev, flags);
hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
dev_name(dev->dev));
@@ -200,6 +249,7 @@ static int ssb_ohci_resume(struct ssb_de
static const struct ssb_device_id ssb_ohci_table[] = {
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
SSB_DEVTABLE_END
};
MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);