mirror of https://github.com/hak5/openwrt.git
This repository is a mirror of https://git.openwrt.org/openwrt/openwrt.git It is for reference only and is not active for check-ins or for reporting issues. We will continue to accept Pull Requests here. They will be merged via staging trees then into openwrt.git. All issues should be reported at: https://bugs.openwrt.org
ff2382e36c
wave-1: 2019-05-09: Tweak rate-ctrl: Ramp PER up faster, down slower. This helps throughput in rate-vs-range test, especially with nss1. 2019-05-20: Disable adaptive-CCA. I am not sure it helps, and it may make it slower to detect noise that should tell the system to stop transmitting. If someone has means to test this properly, I'd be happy to work with them. wave-2: 2019-05-15: Fix problem where rate-ctrl sometimes used rix of 0x0. 2019-05-15: Allow raw-tx of encrypted frame. Requires a patch to the driver to use raw mode when skb has WEP flag enabled AND skb is flagged to not be encrypted. Lightly tested. 2019-05-16: Fix tx-hang that happened when rate-ctrl chose an OFDM rate for 20Mhz and sent that as AMPDU. To fix, limit to (V)HT rates if peer is (V)HT. It seems that MCS0 (V)HT20 should have as good of a chance of being detected as CCK or OFDM. 2019-06-06: Disable TX-BFEE, TX-BFER for IBSS connections. I suspect this is part of the tx-hang issue seen with IBSS between two 9984 radios. 2019-06-12: Fix rx-rate reporting in 'fw_stats' logic. This was at least partly due to regressions I had added earlier when working on some multi-vdev enhancements. 2019-6-12: Fix case where extd peer-stats were not always populated. The stats gathering code did not handle error conditions well. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| feeds.conf.default | ||
| rules.mk | ||
README
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org