openwrt/target/linux/ath79/dts/ar9132_tplink_tl-wr941-v2.dts

169 lines
2.5 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9132.dtsi"
/ {
compatible = "tplink,tl-wr941-v2", "qca,ar9132";
model = "TP-Link TL-WR941N/ND v2/v3";
aliases {
led-boot = &led_system;
led-failsafe = &led_system;
led-running = &led_system;
led-upgrade = &led_system;
label-mac-device = &eth0;
};
keys {
compatible = "gpio-keys";
button0 {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
button1 {
label = "qss";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
leds {
compatible = "gpio-leds";
led_system: system {
label = "tp-link:green:system";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
};
qss_r {
label = "tp-link:red:qss";
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
};
qss_g {
label = "tp-link:green:qss";
gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
};
wlan {
label = "tp-link:green:wlan";
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
dsa {
compatible = "marvell,dsa";
#address-cells = <1>;
#size-cells = <0>;
dsa,mii-bus = <&mdio0>;
dsa,ethernet = <&eth0>;
switch@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
port@0 {
reg = <0>;
label = "wan";
};
port@1 {
reg = <1>;
label = "lan1";
};
port@2 {
reg = <2>;
label = "lan2";
};
port@3 {
reg = <3>;
label = "lan3";
};
port@4 {
reg = <4>;
label = "lan4";
};
port@5 {
reg = <5>;
label = "cpu";
};
};
};
};
&uart {
status = "okay";
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x20000>;
read-only;
};
partition@20000 {
compatible = "tplink,firmware";
label = "firmware";
reg = <0x020000 0x3d0000>;
};
art: partition@3f0000 {
label = "art";
reg = <0x3f0000 0x10000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
};
&eth0 {
status = "okay";
phy-mode = "rmii";
mtd-mac-address = <&uboot 0x1fc00>;
fixed-link {
speed = <100>;
full-duplex;
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&uboot 0x1fc00>;
};