openwrt/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v2...

168 lines
2.5 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca9557.dtsi"
/ {
compatible = "openmesh,om5p-ac-v2", "qca,qca9557";
model = "OpenMesh OM5P-AC V2";
extosc: ref {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-output-names = "ref";
clock-frequency = <40000000>;
};
leds {
compatible = "gpio-leds";
power {
label = "om5pac:blue:power";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
default-state = "off";
};
wifi_green {
label = "om5pac:green:wifi";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
default-state = "off";
};
wifi_yellow {
label = "om5pac:yellow:wifi";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
default-state = "off";
};
wifi_red {
label = "om5pac:red:wifi";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <100>;
button0 {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
};
};
gpio-export {
compatible = "gpio-export";
#size-cells = <0>;
gpio_pa_dcdc {
gpio-export,name = "om5pac:pa_dcdc";
gpio-export,output = <1>;
gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
};
gpio_pa_high {
gpio-export,name = "om5pac:pa_high";
gpio-export,output = <1>;
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
};
};
};
&pinmux {
pinmux_pa_dcdc_pins {
pinctrl-single,bits = <0x0 0xff00 0x0>;
};
pinmux_pa_high_pins {
pinctrl-single,bits = <0x10 0xff 0x0>;
};
};
&pcie0 {
status = "okay";
};
&uart {
status = "okay";
};
&pll {
clocks = <&extosc>;
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@1 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@2 {
label = "firmware";
reg = <0x850000 0x7a0000>;
};
partition@3 {
label = "ART";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy4: ethernet-phy@4 {
reg = <4>;
phy-mode = "rgmii-id";
};
};
&mdio1 {
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
phy-mode = "sgmii";
};
};
&eth0 {
status = "okay";
phy-handle = <&phy4>;
phy-mode = "rgmii";
};
&eth1 {
status = "okay";
phy-handle = <&phy1>;
phy-mode = "sgmii";
};