openwrt/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4029-ap-303.dts

420 lines
7.1 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0 OR MIT
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
model = "Aruba AP-303";
compatible = "aruba,ap-303";
aliases {
led-boot = &led_system_green;
led-failsafe = &led_system_red;
led-running = &led_system_green;
led-upgrade = &led_system_red;
};
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>;
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
/delete-node/ ethernet-phy@0;
/delete-node/ ethernet-phy@2;
/delete-node/ ethernet-phy@3;
/delete-node/ ethernet-phy@4;
ethernet-phy@5 {
reg = <0x5>;
};
};
counter@4a1000 {
compatible = "qcom,qca-gcnt";
reg = <0x4a1000 0x4>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
switch_lan_bmp = <0x0>; /* lan port bitmap */
switch_wan_bmp = <0x10>; /* wan port bitmap */
};
edma@c080000 {
qcom,single-phy;
qcom,num_gmac = <1>;
phy-mode = "rgmii-id";
status = "okay";
};
i2c_0: i2c@78b7000 {
pinctrl-0 = <&i2c_0_pins>;
pinctrl-names = "default";
status = "ok";
tpm@29 {
/* No Driver */
compatible = "atmel,at97sc3203";
reg = <0x29>;
read-only;
};
};
};
leds {
compatible = "gpio-leds";
wifi_green {
label = "ap-303:green:wifi";
gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tpt";
};
wifi_amber {
label = "ap-303:amber:wifi";
gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy1tpt";
};
led_system_red: system_red {
label = "ap-303:red:system";
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
};
led_system_green: system_green {
label = "ap-303:green:system";
gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset button";
gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_uart1 {
/* Texas Instruments CC2540T BLE radio */
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
status = "okay";
};
&blsp1_uart2 {
pinctrl-0 = <&serial_1_pins>;
pinctrl-names = "default";
status = "okay";
};
&cryptobam {
status = "okay";
};
&gmac0 {
qcom,phy_mdio_addr = <5>;
qcom,poll_required = <1>;
vlan_tag = <0 0x20>;
};
&qpic_bam {
status = "okay";
};
&tlmm {
/*
* In addition to the Pins listed below,
* the following GPIOs have "features":
* 54 - out - active low to force HW reset
* 41 - out - active low to reset TPM
* 43 - out - active low to reset BLE radio
* 19 - in - active high when DC powered
*/
mdio_pins: mdio_pinmux {
mux_1 {
pins = "gpio6";
function = "mdio";
bias-pull-up;
};
mux_2 {
pins = "gpio7";
function = "mdc";
bias-pull-up;
};
};
nand_pins: nand_pins {
pullups {
pins = "gpio53", "gpio58", "gpio59";
function = "qpic";
bias-pull-up;
};
pulldowns {
pins = "gpio54", "gpio55", "gpio56",
"gpio57", "gpio60", "gpio61",
"gpio62", "gpio63", "gpio64",
"gpio65", "gpio66", "gpio67",
"gpio68", "gpio69";
function = "qpic";
bias-pull-down;
};
};
spi_0_pins: spi_0_pinmux {
pin {
function = "blsp_spi0";
pins = "gpio13", "gpio14", "gpio15";
drive-strength = <12>;
bias-disable;
};
pin_cs {
function = "gpio";
pins = "gpio12";
drive-strength = <2>;
bias-disable;
output-high;
};
};
i2c_0_pins: i2c_0_pinmux {
mux {
pins = "gpio10", "gpio11";
function = "blsp_i2c0";
drive-strength = <4>;
bias-disable;
};
};
serial_0_pins: serial_0_pinmux {
mux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
};
serial_1_pins: serial_1_pinmux {
mux {
pins = "gpio8", "gpio9";
function = "blsp_uart1";
bias-disable;
};
};
phy-reset {
line-name = "PHY-reset";
gpios = <42 GPIO_ACTIVE_HIGH>;
gpio-hog;
output-high;
};
};
&nand {
pinctrl-0 = <&nand_pins>;
pinctrl-names = "default";
status = "okay";
nand@0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
/* 'aos0' in Aruba firmware */
label = "aos0";
reg = <0x0 0x2000000>;
read-only;
};
partition@2000000 {
/* 'aos1' in AVM firmware */
label = "ubi";
reg = <0x2000000 0x2000000>;
};
partition@4000000 {
label = "aruba-ubifs";
reg = <0x4000000 0x4000000>;
read-only;
};
};
};
};
&blsp1_spi1 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "okay";
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <24000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
/*
* There is no partition map for the NOR flash
* in the stock firmware.
*
* All partitions here are based on offsets
* found in the U-Boot GPL code and information
* from smem.
*/
partition@0 {
label = "sbl1";
reg = <0x0 0x40000>;
read-only;
};
partition@40000 {
label = "mibib";
reg = <0x40000 0x20000>;
read-only;
};
partition@60000 {
label = "qsee";
reg = <0x60000 0x60000>;
read-only;
};
partition@c0000 {
label = "cdt";
reg = <0xc0000 0x10000>;
read-only;
};
partition@d0000 {
label = "ddrparams";
reg = <0xd0000 0x10000>;
read-only;
};
partition@e0000 {
label = "ART";
reg = <0xe0000 0x10000>;
read-only;
};
partition@f0000 {
label = "appsbl";
reg = <0xf0000 0xf0000>;
read-only;
};
partition@1e0000 {
label = "mfginfo";
reg = <0x1e0000 0x10000>;
read-only;
};
partition@1f0000 {
label = "apcd";
reg = <0x1f0000 0x10000>;
read-only;
};
partition@200000 {
label = "osss";
reg = <0x200000 0x180000>;
read-only;
};
partition@380000 {
/* This is empty */
label = "appsblenv";
reg = <0x380000 0x10000>;
read-only;
};
partition@390000 {
label = "pds";
reg = <0x390000 0x10000>;
read-only;
};
partition@3a0000 {
label = "fcache";
reg = <0x3a0000 0x10000>;
read-only;
};
partition@3b0000 {
/* Called osss1 in smem */
label = "u-boot-env-bak";
reg = <0x3b0000 0x10000>;
read-only;
};
partition@3f0000 {
label = "u-boot-env";
reg = <0x3f0000 0x10000>;
read-only;
};
};
};
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "Aruba-AP-303";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "Aruba-AP-303";
};