openwrt/target/linux/ath79/dts/ar7161_netgear_wndr3800.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "ar7100.dtsi"

/ {
	compatible = "netgear,wndr3800", "qca,ar7161";
	model = "Netgear WNDR3800";

	aliases {
		led-status = &power_green;
	};

	chosen {
		bootargs = "console=ttyS0,115200";
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x8000000>;
	};

	extosc: ref {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-output-names = "ref";
		clock-frequency = <40000000>;
	};

	reset-leds {
		compatible = "reset-leds";

		usb_led {
			label = "netgear:green:usb";
			resets = <&rst 12>;
			trigger-sources = <&usb_ochi_port>, <&usb_echi_port>;
			linux,default-trigger = "usbport";
		};
	};

	gpio-leds {
		compatible = "gpio-leds";

		wps {
			label = "netgear:orange:wps";
			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
			default-state = "off";
		};

		power_green: power_green {
			label = "netgear:green:power";
			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
			default-state = "off";
		};

		power_orange {
			label = "netgear:orange:power";
			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
			default-state = "off";
		};

		wps_green {
			label = "netgear:green:wps";
			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
			default-state = "off";
		};

		wan_green {
			label = "netgear:green:wan";
			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
			default-state = "off";
		};
	};

	gpio-keys-polled {
		compatible = "gpio-keys-polled";
		#address-cells = <1>;
		#size-cells = <0>;
		poll-interval = <100>;

		wps {
			label = "wps";
			linux,code = <KEY_WPS_BUTTON>;
			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
		};

		reset {
			label = "reset";
			linux,code = <KEY_RESTART>;
			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
		};

		rfkill {
			label = "rfkill";
			linux,code = <KEY_RFKILL>;
			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
		};
	};

	rtl8366s {
		compatible = "realtek,rtl8366s";
		gpio-sda = <&gpio 5 GPIO_ACTIVE_HIGH>;
		gpio-sck = <&gpio 7 GPIO_ACTIVE_HIGH>;

		mdio-bus {
			status = "okay";

			phy-mask = <0x10>;

			phy4: ethernet-phy@4 {
				reg = <4>;
				phy-mode = "rgmii";
			};
		};
	};
};

&usb_phy {
	status = "okay";
};

&usb1 {
	status = "okay";

	usb_ochi_port: port@1 {
		reg = <1>;
		#trigger-source-cells = <0>;
	};
};

&usb2 {
	status = "okay";

	usb_echi_port: port@1 {
		reg = <1>;
		#trigger-source-cells = <0>;
	};
};

&pcie0 {
	status = "okay";
};

&uart {
	status = "okay";
};

&spi {
	status = "okay";
	num-cs = <1>;

	flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "mx25l12805d";
		reg = <0>;
		spi-max-frequency = <25000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "u-boot";
				reg = <0x000000 0x050000>;
				read-only;
			};

			partition@1 {
				label = "u-boot-env";
				reg = <0x050000 0x020000>;
				read-only;
			};

			partition@2 {
				label = "firmware";
				reg = <0x070000 0xf80000>;
			};

			art: partition@3 {
				label = "art";
				reg = <0xff0000 0x010000>;
				read-only;
			};
		};
	};
};

&eth0 {
	status = "okay";

	pll-data = <0x11110000 0x00001099 0x00991099>;

	mtd-mac-address = <&art 0x00>;

	fixed-link {
		speed = <1000>;
		full-duplex;
	};
};

&eth1 {
	status = "okay";

	pll-data = <0x11110000 0x00001099 0x00991099>;

	mtd-mac-address = <&art 0x06>;

	resets = <&rst 13>;
	reset-names = "mac";

	phy-handle = <&phy4>;
};