openwrt/target/linux/lantiq/dts/FRITZ7360SL.dts

228 lines
4.3 KiB
Plaintext

/dts-v1/;
#include "vr9.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "FRITZ7360SL - 1&1 HomeServer";
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
};
aliases {
led-boot = &power_green;
led-failsafe = &power_red;
led-running = &power_green;
led-internet = &info_green;
led-dsl = &power_green;
led-wifi = &wifi;
};
memory@0 {
reg = <0x0 0x8000000>;
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x1000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
urlader: partition@0 {
label = "urlader";
reg = <0x00000 0x20000>;
read-only;
};
partition@20000 {
label = "firmware";
reg = <0x20000 0xf60000>;
};
partition@f80000 {
label = "tffs (1)";
reg = <0xf80000 0x40000>;
read-only;
};
partition@fc0000 {
label = "tffs (2)";
reg = <0xfc0000 0x40000>;
read-only;
};
};
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
mdio {
lantiq,groups = "mdio";
lantiq,function = "mdio";
};
phy-rst {
lantiq,pins = "io37", "io44";
lantiq,pull = <2>;
lantiq,open-drain;
lantiq,output = <1>;
};
pcie-rst {
lantiq,pins = "io38";
lantiq,pull = <0>;
lantiq,output = <1>;
};
};
};
ifxhcd@E101000 {
status = "okay";
lantiq,portmask = <0x3>;
};
ifxhcd@E106000 {
status = "okay";
};
};
gphy-xrx200 {
compatible = "lantiq,phy-xrx200";
firmware = "lantiq/vr9_phy11g_a2x.bin";
phys = [ 00 01 ];
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
dect {
label = "dect";
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_PHONE>;
};
wifi {
label = "wifi";
gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_WLAN>;
};
};
gpio-leds {
compatible = "gpio-leds";
power_green: power {
label = "fritz7360sl:green:power";
gpios = <&gpio 32 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
power_red: power2 {
label = "fritz7360sl:red:power";
gpios = <&gpio 33 GPIO_ACTIVE_LOW>;
};
info_red {
label = "fritz7360sl:red:info";
gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
};
info_green: info_green {
label = "fritz7360sl:green:info";
gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
};
wifi: wifi {
label = "fritz7360sl:green:wlan";
gpios = <&gpio 36 GPIO_ACTIVE_LOW>;
};
dect {
label = "fritz7360sl:green:dect";
gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
};
};
};
&eth0 {
lan: interface@0 {
compatible = "lantiq,xrx200-pdi";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
mac-address = [ 00 11 22 33 44 55 ];
lantiq,switch;
ethernet@0 {
compatible = "lantiq,xrx200-pdi-port";
reg = <0>;
phy-mode = "rmii";
phy-handle = <&phy0>;
// gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
};
ethernet@1 {
compatible = "lantiq,xrx200-pdi-port";
reg = <1>;
phy-mode = "rmii";
phy-handle = <&phy1>;
// gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
ethernet@2 {
compatible = "lantiq,xrx200-pdi-port";
reg = <2>;
phy-mode = "gmii";
phy-handle = <&phy11>;
};
ethernet@3 {
compatible = "lantiq,xrx200-pdi-port";
reg = <4>;
phy-mode = "gmii";
phy-handle = <&phy13>;
};
};
mdio@0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "lantiq,xrx200-mdio";
phy0: ethernet-phy@0 {
reg = <0x00>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy1: ethernet-phy@1 {
reg = <0x01>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy11: ethernet-phy@11 {
reg = <0x11>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
phy13: ethernet-phy@13 {
reg = <0x13>;
compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
};
};
};
&pcie0 {
pcie@0 {
reg = <0 0 0 0 0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
device_type = "pci";
wifi@168c,002e {
compatible = "pci168c,002e";
reg = <0 0 0 0 0>;
qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */
};
};
};