mirror of https://github.com/hak5/openwrt.git
66 lines
2.3 KiB
Diff
66 lines
2.3 KiB
Diff
From: Benjamin Berg <benjamin.berg@open-mesh.com>
|
|
Date: Mon, 4 Jul 2016 14:37:22 +0200
|
|
Subject: [PATCH] ath9k: Use tsf offset helper in ath9k_hw_reset
|
|
|
|
These changes make ath9k_hw_reset more consistent with other places that
|
|
handle the TSF value by using the same helper routine.
|
|
|
|
A slight improvement is to not assume that a fixed time of 1.5ms has
|
|
passed for the initval writes when compared to the first write attempt.
|
|
Instead the TSF value is re-calculated which will yield a higher accuracy
|
|
of the restored TSF timer.
|
|
|
|
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
|
|
---
|
|
|
|
--- a/drivers/net/wireless/ath/ath9k/hw.c
|
|
+++ b/drivers/net/wireless/ath/ath9k/hw.c
|
|
@@ -1832,8 +1832,9 @@ int ath9k_hw_reset(struct ath_hw *ah, st
|
|
u32 saveLedState;
|
|
u32 saveDefAntenna;
|
|
u32 macStaId1;
|
|
+ struct timespec tsf_ts;
|
|
+ u32 tsf_offset;
|
|
u64 tsf = 0;
|
|
- s64 usec = 0;
|
|
int r;
|
|
bool start_mci_reset = false;
|
|
bool save_fullsleep = ah->chip_fullsleep;
|
|
@@ -1877,8 +1878,8 @@ int ath9k_hw_reset(struct ath_hw *ah, st
|
|
macStaId1 = REG_READ(ah, AR_STA_ID1) & AR_STA_ID1_BASE_RATE_11B;
|
|
|
|
/* Save TSF before chip reset, a cold reset clears it */
|
|
+ getrawmonotonic(&tsf_ts);
|
|
tsf = ath9k_hw_gettsf64(ah);
|
|
- usec = ktime_to_us(ktime_get_raw());
|
|
|
|
saveLedState = REG_READ(ah, AR_CFG_LED) &
|
|
(AR_CFG_LED_ASSOC_CTL | AR_CFG_LED_MODE_SEL |
|
|
@@ -1911,8 +1912,8 @@ int ath9k_hw_reset(struct ath_hw *ah, st
|
|
}
|
|
|
|
/* Restore TSF */
|
|
- usec = ktime_to_us(ktime_get_raw()) - usec;
|
|
- ath9k_hw_settsf64(ah, tsf + usec);
|
|
+ tsf_offset = ath9k_hw_get_tsf_offset(&tsf_ts, NULL);
|
|
+ ath9k_hw_settsf64(ah, tsf + tsf_offset);
|
|
|
|
if (AR_SREV_9280_20_OR_LATER(ah))
|
|
REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL, AR_GPIO_JTAG_DISABLE);
|
|
@@ -1932,12 +1933,11 @@ int ath9k_hw_reset(struct ath_hw *ah, st
|
|
/*
|
|
* Some AR91xx SoC devices frequently fail to accept TSF writes
|
|
* right after the chip reset. When that happens, write a new
|
|
- * value after the initvals have been applied, with an offset
|
|
- * based on measured time difference
|
|
+ * value after the initvals have been applied.
|
|
*/
|
|
if (AR_SREV_9100(ah) && (ath9k_hw_gettsf64(ah) < tsf)) {
|
|
- tsf += 1500;
|
|
- ath9k_hw_settsf64(ah, tsf);
|
|
+ tsf_offset = ath9k_hw_get_tsf_offset(&tsf_ts, NULL);
|
|
+ ath9k_hw_settsf64(ah, tsf + tsf_offset);
|
|
}
|
|
|
|
ath9k_hw_init_mfp(ah);
|