openwrt/target/linux/ath79/dts/qca9531_comfast_cf-e313ac.dts

149 lines
2.4 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca953x.dtsi"
/ {
compatible = "comfast,cf-e313ac", "qca,qca9531";
model = "COMFAST CF-E313AC";
aliases {
serial0 = &uart;
led-boot = &led_rssihigh;
led-failsafe = &led_rssihigh;
led-upgrade = &led_rssihigh;
label-mac-device = &eth1;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
wlan {
label = "cf-e313ac:green:wlan";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
lan {
label = "cf-e313ac:green:lan";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
};
wan {
label = "cf-e313ac:green:wan";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
rssilow {
label = "cf-e313ac:red:rssilow";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
rssimediumlow {
label = "cf-e313ac:red:rssimediumlow";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
rssimediumhigh {
label = "cf-e313ac:green:rssimediumhigh";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
led_rssihigh: rssihigh {
label = "cf-e313ac:green:rssihigh";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x010000>;
read-only;
};
art: partition@10000 {
label = "art";
reg = <0x010000 0x010000>;
read-only;
};
partition@20000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x020000 0x7c0000>;
};
partition@7e0000 {
label = "config";
reg = <0x7e0000 0x010000>;
read-only;
};
partition@7f0000 {
label = "nvram";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&uart {
status = "okay";
};
&eth0 {
status = "okay";
phy-handle = <&swphy0>;
mtd-mac-address = <&art 0x1002>;
gmac-config {
device = <&gmac>;
switch-phy-swap = <1>;
};
};
&eth1 {
status = "okay";
mtd-mac-address = <&art 0x0>;
};
&pcie0 {
status = "okay";
wifi@0,0 {
compatible = "qcom,ath10k";
reg = <0 0 0 0 0>;
};
};