openwrt/target/linux/ath79/dts/ar9344_dlink_dir-8x5.dtsi

151 lines
2.3 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "ar9344.dtsi"
/ {
chosen {
bootargs = "console=ttyS0,115200";
};
keys {
compatible = "gpio-keys";
reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
wps {
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&eth0 {
status = "okay";
/* default for ar934x, except for 1000M */
pll-data = <0x06000000 0x00000101 0x00001616>;
phy-mode = "rgmii";
phy-handle = <&phy0>;
};
&mdio0 {
status = "okay";
phy-mask = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
/* GPL code drop (bsp.h & athrs17_phy.c) */
0x10 0xc1000000 /* PWS_REG_VALUE */
0x04 0x07600000 /* PORT0 PAD Mode */
0x0c 0x01000000 /* PORT6 PAD Mode */
0x7c 0x0000007e /* PORT0_STATUS */
0x94 0x0000007e /* PORT6_STATUS */
>;
};
};
&pcie {
status = "okay";
ath9k: wifi@0,0 {
compatible = "pci168c,0030";
reg = <0x0000 0 0 0 0>;
qca,no-eeprom;
gpio-controller;
#gpio-cells = <2>;
};
};
&ref {
clock-frequency = <40000000>;
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x000000 0x010000>;
read-only;
};
partition@10000 {
label = "nvram";
reg = <0x010000 0x010000>;
read-only;
};
partition@20000 {
label = "firmware";
reg = <0x020000 0xF90000>;
compatible = "denx,uimage";
};
partition@fb0000 {
label = "lang";
reg = <0xfb0000 0x030000>;
read-only;
};
partition@fe0000 {
label = "mac";
reg = <0xfe0000 0x010000>;
read-only;
};
partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&uart {
status = "okay";
};
&usb {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
hub_port1: port@1 {
reg = <1>;
#trigger-source-cells = <0>;
};
};
&usb_phy {
status = "okay";
};
&wmac {
status = "okay";
qca,no-eeprom;
};