mirror of https://github.com/hak5/openwrt.git
220 lines
3.4 KiB
Plaintext
220 lines
3.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9344.dtsi"
|
|
|
|
/ {
|
|
model = "Winchannel WB2000";
|
|
compatible = "winchannel,wb2000", "qca,ar9344";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
};
|
|
|
|
i2c {
|
|
compatible = "i2c-gpio";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_HIGH
|
|
&gpio 16 GPIO_ACTIVE_HIGH
|
|
>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1339";
|
|
reg = <0x68>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan2g {
|
|
label = "wb2000:green:2g";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
usb {
|
|
label = "wb2000:green:usb";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
|
|
trigger-sources = <&hub_port1>, <&hub_port2>;
|
|
linux,default-trigger = "usbport";
|
|
};
|
|
|
|
led_system: system {
|
|
label = "wb2000:green:system";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
ath9k-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan {
|
|
label = "wb2000:green:5g";
|
|
gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
num-cs = <1>;
|
|
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0xf80000>;
|
|
compatible = "denx,uimage";
|
|
};
|
|
|
|
partition@fd0000 {
|
|
label = "nvram";
|
|
reg = <0xfd0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@fe0000 {
|
|
label = "art";
|
|
reg = <0xfe0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
addr: partition@ff0000 {
|
|
label = "addr";
|
|
reg = <0xff0000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
ath9k: wifi@0,0 {
|
|
compatible = "pci168c,0030";
|
|
reg = <0x0000 0 0 0 0>;
|
|
qca,no-eeprom;
|
|
mtd-mac-address = <&addr 0x0>;
|
|
mtd-mac-address-increment = <0x10>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
};
|
|
};
|
|
|
|
&usb {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
port@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
|
|
hub_port1: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
|
|
hub_port2: port@2 {
|
|
reg = <2>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&addr 0x0>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0x10>;
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0xe000000 0x04000101 0x04001313>;
|
|
|
|
mtd-mac-address = <&addr 0x0>;
|
|
mtd-mac-address-increment = <0x21>;
|
|
|
|
phy-mode = "rgmii-rxid";
|
|
phy-handle = <&phy4>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
rgmii-gmac0 = <1>;
|
|
rxd-delay = <1>;
|
|
rxdv-delay = <1>;
|
|
};
|
|
};
|