openwrt/target/linux/generic/pending-4.19/110-ehci_hcd_ignore_oc.patch

80 lines
2.8 KiB
Diff

From: Florian Fainelli <florian@openwrt.org>
Subject: USB: EHCI: add ignore_oc flag to disable overcurrent checking
This patch adds an ignore_oc flag which can be set by EHCI controller
not supporting or wanting to disable overcurrent checking. The EHCI
platform data in include/linux/usb/ehci_pdriver.h is also augmented to
take advantage of this new flag.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
---
drivers/usb/host/ehci-hcd.c | 2 +-
drivers/usb/host/ehci-hub.c | 4 ++--
drivers/usb/host/ehci-platform.c | 1 +
drivers/usb/host/ehci.h | 1 +
include/linux/usb/ehci_pdriver.h | 1 +
5 files changed, 6 insertions(+), 3 deletions(-)
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -638,7 +638,7 @@ static int ehci_run (struct usb_hcd *hcd
"USB %x.%x started, EHCI %x.%02x%s\n",
((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f),
temp >> 8, temp & 0xff,
- ignore_oc ? ", overcurrent ignored" : "");
+ (ignore_oc || ehci->ignore_oc) ? ", overcurrent ignored" : "");
ehci_writel(ehci, INTR_MASK,
&ehci->regs->intr_enable); /* Turn On Interrupts */
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -641,7 +641,7 @@ ehci_hub_status_data (struct usb_hcd *hc
* always set, seem to clear PORT_OCC and PORT_CSC when writing to
* PORT_POWER; that's surprising, but maybe within-spec.
*/
- if (!ignore_oc)
+ if (!ignore_oc && !ehci->ignore_oc)
mask = PORT_CSC | PORT_PEC | PORT_OCC;
else
mask = PORT_CSC | PORT_PEC;
@@ -1011,7 +1011,7 @@ int ehci_hub_control(
if (temp & PORT_PEC)
status |= USB_PORT_STAT_C_ENABLE << 16;
- if ((temp & PORT_OCC) && !ignore_oc){
+ if ((temp & PORT_OCC) && (!ignore_oc && !ehci->ignore_oc)){
status |= USB_PORT_STAT_C_OVERCURRENT << 16;
/*
--- a/drivers/usb/host/ehci-platform.c
+++ b/drivers/usb/host/ehci-platform.c
@@ -208,6 +208,8 @@ static int ehci_platform_probe(struct pl
hcd->has_tt = 1;
if (pdata->reset_on_resume)
priv->reset_on_resume = true;
+ if (pdata->ignore_oc)
+ ehci->ignore_oc = 1;
#ifndef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
if (ehci->big_endian_mmio) {
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -218,6 +218,7 @@ struct ehci_hcd { /* one per controlle
unsigned frame_index_bug:1; /* MosChip (AKA NetMos) */
unsigned need_oc_pp_cycle:1; /* MPC834X port power */
unsigned imx28_write_fix:1; /* For Freescale i.MX28 */
+ unsigned ignore_oc:1;
/* required for usb32 quirk */
#define OHCI_CTRL_HCFS (3 << 6)
--- a/include/linux/usb/ehci_pdriver.h
+++ b/include/linux/usb/ehci_pdriver.h
@@ -50,6 +50,7 @@ struct usb_ehci_pdata {
unsigned no_io_watchdog:1;
unsigned reset_on_resume:1;
unsigned dma_mask_64:1;
+ unsigned ignore_oc:1;
/* Turn on all power and clocks */
int (*power_on)(struct platform_device *pdev);