mirror of https://github.com/hak5/openwrt.git
88 lines
3.0 KiB
Diff
88 lines
3.0 KiB
Diff
From: Miaoqing Pan <miaoqing@codeaurora.org>
|
|
Date: Fri, 5 Feb 2016 09:45:50 +0800
|
|
Subject: [PATCH] ath9k: make NF load complete quickly and reliably
|
|
|
|
Make NF load complete quickly and reliably. NF load execution
|
|
is delayed by HW to end of frame if frame Rx or Tx is ongoing.
|
|
Increasing timeout to max frame duration. If NF cal is ongoing
|
|
before NF load, stop it before load, and restart it afterwards.
|
|
|
|
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
|
|
---
|
|
|
|
--- a/drivers/net/wireless/ath/ath9k/calib.c
|
|
+++ b/drivers/net/wireless/ath/ath9k/calib.c
|
|
@@ -241,6 +241,7 @@ int ath9k_hw_loadnf(struct ath_hw *ah, s
|
|
u8 chainmask = (ah->rxchainmask << 3) | ah->rxchainmask;
|
|
struct ath_common *common = ath9k_hw_common(ah);
|
|
s16 default_nf = ath9k_hw_get_default_nf(ah, chan);
|
|
+ u32 bb_agc_ctl = REG_READ(ah, AR_PHY_AGC_CONTROL);
|
|
|
|
if (ah->caldata)
|
|
h = ah->caldata->nfCalHist;
|
|
@@ -264,6 +265,16 @@ int ath9k_hw_loadnf(struct ath_hw *ah, s
|
|
}
|
|
|
|
/*
|
|
+ * stop NF cal if ongoing to ensure NF load completes immediately
|
|
+ * (or after end rx/tx frame if ongoing)
|
|
+ */
|
|
+ if (bb_agc_ctl & AR_PHY_AGC_CONTROL_NF) {
|
|
+ REG_CLR_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
|
|
+ REG_RMW_BUFFER_FLUSH(ah);
|
|
+ ENABLE_REG_RMW_BUFFER(ah);
|
|
+ }
|
|
+
|
|
+ /*
|
|
* Load software filtered NF value into baseband internal minCCApwr
|
|
* variable.
|
|
*/
|
|
@@ -276,18 +287,33 @@ int ath9k_hw_loadnf(struct ath_hw *ah, s
|
|
|
|
/*
|
|
* Wait for load to complete, should be fast, a few 10s of us.
|
|
- * The max delay was changed from an original 250us to 10000us
|
|
- * since 250us often results in NF load timeout and causes deaf
|
|
- * condition during stress testing 12/12/2009
|
|
+ * The max delay was changed from an original 250us to 22.2 msec.
|
|
+ * This would increase timeout to the longest possible frame
|
|
+ * (11n max length 22.1 msec)
|
|
*/
|
|
- for (j = 0; j < 10000; j++) {
|
|
+ for (j = 0; j < 22200; j++) {
|
|
if ((REG_READ(ah, AR_PHY_AGC_CONTROL) &
|
|
- AR_PHY_AGC_CONTROL_NF) == 0)
|
|
+ AR_PHY_AGC_CONTROL_NF) == 0)
|
|
break;
|
|
udelay(10);
|
|
}
|
|
|
|
/*
|
|
+ * Restart NF so it can continue.
|
|
+ */
|
|
+ if (bb_agc_ctl & AR_PHY_AGC_CONTROL_NF) {
|
|
+ ENABLE_REG_RMW_BUFFER(ah);
|
|
+ if (bb_agc_ctl & AR_PHY_AGC_CONTROL_ENABLE_NF)
|
|
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
|
|
+ AR_PHY_AGC_CONTROL_ENABLE_NF);
|
|
+ if (bb_agc_ctl & AR_PHY_AGC_CONTROL_NO_UPDATE_NF)
|
|
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL,
|
|
+ AR_PHY_AGC_CONTROL_NO_UPDATE_NF);
|
|
+ REG_SET_BIT(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_NF);
|
|
+ REG_RMW_BUFFER_FLUSH(ah);
|
|
+ }
|
|
+
|
|
+ /*
|
|
* We timed out waiting for the noisefloor to load, probably due to an
|
|
* in-progress rx. Simply return here and allow the load plenty of time
|
|
* to complete before the next calibration interval. We need to avoid
|
|
@@ -296,7 +322,7 @@ int ath9k_hw_loadnf(struct ath_hw *ah, s
|
|
* here, the baseband nf cal will just be capped by our present
|
|
* noisefloor until the next calibration timer.
|
|
*/
|
|
- if (j == 10000) {
|
|
+ if (j == 22200) {
|
|
ath_dbg(common, ANY,
|
|
"Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x%x\n",
|
|
REG_READ(ah, AR_PHY_AGC_CONTROL));
|