mirror of https://github.com/hak5/openwrt.git
334 lines
10 KiB
C
334 lines
10 KiB
C
#ifndef __LINUX_ETRAX_USB_H
|
|
#define __LINUX_ETRAX_USB_H
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/list.h>
|
|
|
|
struct USB_IN_Desc {
|
|
volatile __u16 sw_len;
|
|
volatile __u16 command;
|
|
volatile unsigned long next;
|
|
volatile unsigned long buf;
|
|
volatile __u16 hw_len;
|
|
volatile __u16 status;
|
|
};
|
|
|
|
struct USB_SB_Desc {
|
|
volatile __u16 sw_len;
|
|
volatile __u16 command;
|
|
volatile unsigned long next;
|
|
volatile unsigned long buf;
|
|
};
|
|
|
|
struct USB_EP_Desc {
|
|
volatile __u16 hw_len;
|
|
volatile __u16 command;
|
|
volatile unsigned long sub;
|
|
volatile unsigned long next;
|
|
};
|
|
|
|
|
|
/* Root Hub port status struct */
|
|
struct crisv10_rh {
|
|
volatile __u16 wPortChange[2];
|
|
volatile __u16 wPortStatusPrev[2];
|
|
};
|
|
|
|
/* HCD description */
|
|
struct crisv10_hcd {
|
|
spinlock_t lock;
|
|
__u8 num_ports;
|
|
__u8 running;
|
|
};
|
|
|
|
|
|
/* Endpoint HC private data description */
|
|
struct crisv10_ep_priv {
|
|
int epid;
|
|
};
|
|
|
|
/* Additional software state info for a USB Controller epid */
|
|
struct etrax_epid {
|
|
__u8 inuse; /* !0 = setup in Etrax and used for a endpoint */
|
|
__u8 disabled; /* !0 = Temporarly disabled to avoid resubmission */
|
|
__u8 type; /* Setup as: PIPE_BULK, PIPE_CONTROL ... */
|
|
__u8 out_traffic; /* !0 = This epid is for out traffic */
|
|
};
|
|
|
|
/* Struct to hold information of scheduled later URB completion */
|
|
struct urb_later_data {
|
|
struct delayed_work dws;
|
|
struct usb_hcd *hcd;
|
|
struct urb *urb;
|
|
int urb_num;
|
|
int status;
|
|
};
|
|
|
|
|
|
typedef enum {
|
|
STARTED,
|
|
NOT_STARTED,
|
|
UNLINK,
|
|
} crisv10_urb_state_t;
|
|
|
|
|
|
struct crisv10_urb_priv {
|
|
/* Sequence number for this URB. Every new submited URB gets this from
|
|
a incrementing counter. Used when a URB is scheduled for later finish to
|
|
be sure that the intended URB hasn't already been completed (device
|
|
drivers has a tendency to reuse URBs once they are completed, causing us
|
|
to not be able to single old ones out only based on the URB pointer.) */
|
|
__u32 urb_num;
|
|
|
|
/* The first_sb field is used for freeing all SB descriptors belonging
|
|
to an urb. The corresponding ep descriptor's sub pointer cannot be
|
|
used for this since the DMA advances the sub pointer as it processes
|
|
the sb list. */
|
|
struct USB_SB_Desc *first_sb;
|
|
|
|
/* The last_sb field referes to the last SB descriptor that belongs to
|
|
this urb. This is important to know so we can free the SB descriptors
|
|
that ranges between first_sb and last_sb. */
|
|
struct USB_SB_Desc *last_sb;
|
|
|
|
/* The rx_offset field is used in ctrl and bulk traffic to keep track
|
|
of the offset in the urb's transfer_buffer where incoming data should be
|
|
copied to. */
|
|
__u32 rx_offset;
|
|
|
|
/* Counter used in isochronous transfers to keep track of the
|
|
number of packets received/transmitted. */
|
|
__u32 isoc_packet_counter;
|
|
|
|
/* Flag that marks if this Isoc Out URB has finished it's transfer. Used
|
|
because several URBs can be finished before list is processed */
|
|
__u8 isoc_out_done;
|
|
|
|
/* This field is used to pass information about the urb's current state
|
|
between the various interrupt handlers (thus marked volatile). */
|
|
volatile crisv10_urb_state_t urb_state;
|
|
|
|
/* In Ctrl transfers consist of (at least) 3 packets: SETUP, IN and ZOUT.
|
|
When DMA8 sub-channel 2 has processed the SB list for this sequence we
|
|
get a interrupt. We also get a interrupt for In transfers and which
|
|
one of these interrupts that comes first depends of data size and device.
|
|
To be sure that we have got both interrupts before we complete the URB
|
|
we have these to flags that shows which part that has completed.
|
|
We can then check when we get one of the interrupts that if the other has
|
|
occured it's safe for us to complete the URB, otherwise we set appropriate
|
|
flag and do the completion when we get the other interrupt. */
|
|
volatile unsigned char ctrl_zout_done;
|
|
volatile unsigned char ctrl_rx_done;
|
|
|
|
/* Connection between the submitted urb and ETRAX epid number */
|
|
__u8 epid;
|
|
|
|
/* The rx_data_list field is used for periodic traffic, to hold
|
|
received data for later processing in the the complete_urb functions,
|
|
where the data us copied to the urb's transfer_buffer. Basically, we
|
|
use this intermediate storage because we don't know when it's safe to
|
|
reuse the transfer_buffer (FIXME?). */
|
|
struct list_head rx_data_list;
|
|
|
|
|
|
/* The interval time rounded up to closest 2^N */
|
|
int interval;
|
|
|
|
/* Pool of EP descriptors needed if it's a INTR transfer.
|
|
Amount of EPs in pool correspons to how many INTR that should
|
|
be inserted in TxIntrEPList (max 128, defined by MAX_INTR_INTERVAL) */
|
|
struct USB_EP_Desc* intr_ep_pool[128];
|
|
|
|
/* The mount of EPs allocated for this INTR URB */
|
|
int intr_ep_pool_length;
|
|
|
|
/* Pointer to info struct if URB is scheduled to be finished later */
|
|
struct urb_later_data* later_data;
|
|
|
|
/* Allocated bandwidth for isochronous and interrupt traffic */
|
|
int bandwidth;
|
|
};
|
|
|
|
|
|
/* This struct is for passing data from the top half to the bottom half irq
|
|
handlers */
|
|
struct crisv10_irq_reg {
|
|
struct usb_hcd* hcd;
|
|
__u32 r_usb_epid_attn;
|
|
__u8 r_usb_status;
|
|
__u16 r_usb_rh_port_status_1;
|
|
__u16 r_usb_rh_port_status_2;
|
|
__u32 r_usb_irq_mask_read;
|
|
__u32 r_usb_fm_number;
|
|
struct work_struct usb_bh;
|
|
};
|
|
|
|
|
|
/* This struct is for passing data from the isoc top half to the isoc bottom
|
|
half. */
|
|
struct crisv10_isoc_complete_data {
|
|
struct usb_hcd *hcd;
|
|
struct urb *urb;
|
|
struct work_struct usb_bh;
|
|
};
|
|
|
|
/* Entry item for URB lists for each endpint */
|
|
typedef struct urb_entry
|
|
{
|
|
struct urb *urb;
|
|
struct list_head list;
|
|
} urb_entry_t;
|
|
|
|
/* ---------------------------------------------------------------------------
|
|
Virtual Root HUB
|
|
------------------------------------------------------------------------- */
|
|
/* destination of request */
|
|
#define RH_INTERFACE 0x01
|
|
#define RH_ENDPOINT 0x02
|
|
#define RH_OTHER 0x03
|
|
|
|
#define RH_CLASS 0x20
|
|
#define RH_VENDOR 0x40
|
|
|
|
/* Requests: bRequest << 8 | bmRequestType */
|
|
#define RH_GET_STATUS 0x0080
|
|
#define RH_CLEAR_FEATURE 0x0100
|
|
#define RH_SET_FEATURE 0x0300
|
|
#define RH_SET_ADDRESS 0x0500
|
|
#define RH_GET_DESCRIPTOR 0x0680
|
|
#define RH_SET_DESCRIPTOR 0x0700
|
|
#define RH_GET_CONFIGURATION 0x0880
|
|
#define RH_SET_CONFIGURATION 0x0900
|
|
#define RH_GET_STATE 0x0280
|
|
#define RH_GET_INTERFACE 0x0A80
|
|
#define RH_SET_INTERFACE 0x0B00
|
|
#define RH_SYNC_FRAME 0x0C80
|
|
/* Our Vendor Specific Request */
|
|
#define RH_SET_EP 0x2000
|
|
|
|
|
|
/* Hub port features */
|
|
#define RH_PORT_CONNECTION 0x00
|
|
#define RH_PORT_ENABLE 0x01
|
|
#define RH_PORT_SUSPEND 0x02
|
|
#define RH_PORT_OVER_CURRENT 0x03
|
|
#define RH_PORT_RESET 0x04
|
|
#define RH_PORT_POWER 0x08
|
|
#define RH_PORT_LOW_SPEED 0x09
|
|
#define RH_C_PORT_CONNECTION 0x10
|
|
#define RH_C_PORT_ENABLE 0x11
|
|
#define RH_C_PORT_SUSPEND 0x12
|
|
#define RH_C_PORT_OVER_CURRENT 0x13
|
|
#define RH_C_PORT_RESET 0x14
|
|
|
|
/* Hub features */
|
|
#define RH_C_HUB_LOCAL_POWER 0x00
|
|
#define RH_C_HUB_OVER_CURRENT 0x01
|
|
|
|
#define RH_DEVICE_REMOTE_WAKEUP 0x00
|
|
#define RH_ENDPOINT_STALL 0x01
|
|
|
|
/* Our Vendor Specific feature */
|
|
#define RH_REMOVE_EP 0x00
|
|
|
|
|
|
#define RH_ACK 0x01
|
|
#define RH_REQ_ERR -1
|
|
#define RH_NACK 0x00
|
|
|
|
/* Field definitions for */
|
|
|
|
#define USB_IN_command__eol__BITNR 0 /* command macros */
|
|
#define USB_IN_command__eol__WIDTH 1
|
|
#define USB_IN_command__eol__no 0
|
|
#define USB_IN_command__eol__yes 1
|
|
|
|
#define USB_IN_command__intr__BITNR 3
|
|
#define USB_IN_command__intr__WIDTH 1
|
|
#define USB_IN_command__intr__no 0
|
|
#define USB_IN_command__intr__yes 1
|
|
|
|
#define USB_IN_status__eop__BITNR 1 /* status macros. */
|
|
#define USB_IN_status__eop__WIDTH 1
|
|
#define USB_IN_status__eop__no 0
|
|
#define USB_IN_status__eop__yes 1
|
|
|
|
#define USB_IN_status__eot__BITNR 5
|
|
#define USB_IN_status__eot__WIDTH 1
|
|
#define USB_IN_status__eot__no 0
|
|
#define USB_IN_status__eot__yes 1
|
|
|
|
#define USB_IN_status__error__BITNR 6
|
|
#define USB_IN_status__error__WIDTH 1
|
|
#define USB_IN_status__error__no 0
|
|
#define USB_IN_status__error__yes 1
|
|
|
|
#define USB_IN_status__nodata__BITNR 7
|
|
#define USB_IN_status__nodata__WIDTH 1
|
|
#define USB_IN_status__nodata__no 0
|
|
#define USB_IN_status__nodata__yes 1
|
|
|
|
#define USB_IN_status__epid__BITNR 8
|
|
#define USB_IN_status__epid__WIDTH 5
|
|
|
|
#define USB_EP_command__eol__BITNR 0
|
|
#define USB_EP_command__eol__WIDTH 1
|
|
#define USB_EP_command__eol__no 0
|
|
#define USB_EP_command__eol__yes 1
|
|
|
|
#define USB_EP_command__eof__BITNR 1
|
|
#define USB_EP_command__eof__WIDTH 1
|
|
#define USB_EP_command__eof__no 0
|
|
#define USB_EP_command__eof__yes 1
|
|
|
|
#define USB_EP_command__intr__BITNR 3
|
|
#define USB_EP_command__intr__WIDTH 1
|
|
#define USB_EP_command__intr__no 0
|
|
#define USB_EP_command__intr__yes 1
|
|
|
|
#define USB_EP_command__enable__BITNR 4
|
|
#define USB_EP_command__enable__WIDTH 1
|
|
#define USB_EP_command__enable__no 0
|
|
#define USB_EP_command__enable__yes 1
|
|
|
|
#define USB_EP_command__hw_valid__BITNR 5
|
|
#define USB_EP_command__hw_valid__WIDTH 1
|
|
#define USB_EP_command__hw_valid__no 0
|
|
#define USB_EP_command__hw_valid__yes 1
|
|
|
|
#define USB_EP_command__epid__BITNR 8
|
|
#define USB_EP_command__epid__WIDTH 5
|
|
|
|
#define USB_SB_command__eol__BITNR 0 /* command macros. */
|
|
#define USB_SB_command__eol__WIDTH 1
|
|
#define USB_SB_command__eol__no 0
|
|
#define USB_SB_command__eol__yes 1
|
|
|
|
#define USB_SB_command__eot__BITNR 1
|
|
#define USB_SB_command__eot__WIDTH 1
|
|
#define USB_SB_command__eot__no 0
|
|
#define USB_SB_command__eot__yes 1
|
|
|
|
#define USB_SB_command__intr__BITNR 3
|
|
#define USB_SB_command__intr__WIDTH 1
|
|
#define USB_SB_command__intr__no 0
|
|
#define USB_SB_command__intr__yes 1
|
|
|
|
#define USB_SB_command__tt__BITNR 4
|
|
#define USB_SB_command__tt__WIDTH 2
|
|
#define USB_SB_command__tt__zout 0
|
|
#define USB_SB_command__tt__in 1
|
|
#define USB_SB_command__tt__out 2
|
|
#define USB_SB_command__tt__setup 3
|
|
|
|
|
|
#define USB_SB_command__rem__BITNR 8
|
|
#define USB_SB_command__rem__WIDTH 6
|
|
|
|
#define USB_SB_command__full__BITNR 6
|
|
#define USB_SB_command__full__WIDTH 1
|
|
#define USB_SB_command__full__no 0
|
|
#define USB_SB_command__full__yes 1
|
|
|
|
#endif
|