mirror of https://github.com/hak5/openwrt.git
128 lines
3.7 KiB
Diff
128 lines
3.7 KiB
Diff
From 52ca91f1e28a45f4584432525b149f32a0048dd0 Mon Sep 17 00:00:00 2001
|
|
From: Michael Heimpold <michael.heimpold@i2se.com>
|
|
Date: Fri, 29 Jan 2016 12:00:37 +0100
|
|
Subject: [PATCH] Add overlay and enable support for QCA7000 board
|
|
|
|
This adds a device tree overlay for the QCA7000 which can be used
|
|
when attaching an I2SE's PLC Stamp micro EVK to the Raspberry Pi.
|
|
|
|
This Evaluation Board embeds a QCA7000 chip, a Homeplug Green PHY
|
|
powerline chip from Qualcomm/Atheros for the Internet of Things.
|
|
|
|
This patch also enables the required QCA7000 driver module
|
|
in the default configurations.
|
|
|
|
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
|
|
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
|
|
---
|
|
arch/arm/boot/dts/overlays/Makefile | 1 +
|
|
arch/arm/boot/dts/overlays/README | 8 ++++
|
|
arch/arm/boot/dts/overlays/qca7000-overlay.dts | 52 ++++++++++++++++++++++++++
|
|
arch/arm/configs/bcm2709_defconfig | 1 +
|
|
arch/arm/configs/bcmrpi_defconfig | 1 +
|
|
5 files changed, 63 insertions(+)
|
|
create mode 100644 arch/arm/boot/dts/overlays/qca7000-overlay.dts
|
|
|
|
--- a/arch/arm/boot/dts/overlays/Makefile
|
|
+++ b/arch/arm/boot/dts/overlays/Makefile
|
|
@@ -48,6 +48,7 @@ dtbo-$(RPI_DT_OVERLAYS) += pitft28-resis
|
|
dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
|
|
dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
|
|
dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
|
|
+dtbo-$(RPI_DT_OVERLAYS) += qca7000.dtbo
|
|
dtbo-$(RPI_DT_OVERLAYS) += raspidac3.dtbo
|
|
dtbo-$(RPI_DT_OVERLAYS) += rpi-backlight.dtbo
|
|
dtbo-$(RPI_DT_OVERLAYS) += rpi-dac.dtbo
|
|
--- a/arch/arm/boot/dts/overlays/README
|
|
+++ b/arch/arm/boot/dts/overlays/README
|
|
@@ -625,6 +625,14 @@ Params: pin Output p
|
|
clock PWM clock frequency (informational)
|
|
|
|
|
|
+Name: qca7000
|
|
+Info: I2SE's Evaluation Board for PLC Stamp micro
|
|
+Load: dtoverlay=qca7000,<param>=<val>
|
|
+Params: int_pin GPIO pin for interrupt signal (default 23)
|
|
+
|
|
+ speed SPI bus speed (default 12 MHz)
|
|
+
|
|
+
|
|
Name: raspidac3
|
|
Info: Configures the RaspiDAV Rev.3x audio card
|
|
Load: dtoverlay=raspidac3
|
|
--- /dev/null
|
|
+++ b/arch/arm/boot/dts/overlays/qca7000-overlay.dts
|
|
@@ -0,0 +1,52 @@
|
|
+// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK
|
|
+// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details
|
|
+
|
|
+/dts-v1/;
|
|
+/plugin/;
|
|
+
|
|
+/ {
|
|
+ compatible = "brcm,bcm2708";
|
|
+
|
|
+ fragment@0 {
|
|
+ target = <&spi0>;
|
|
+ __overlay__ {
|
|
+ /* needed to avoid dtc warning */
|
|
+ #address-cells = <1>;
|
|
+ #size-cells = <0>;
|
|
+
|
|
+ status = "okay";
|
|
+
|
|
+ spidev@0 {
|
|
+ status = "disabled";
|
|
+ };
|
|
+
|
|
+ eth1: qca7000@0 {
|
|
+ compatible = "qca,qca7000";
|
|
+ reg = <0>; /* CE0 */
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <ð1_pins>;
|
|
+ interrupt-parent = <&gpio>;
|
|
+ interrupts = <23 0x1>; /* rising edge */
|
|
+ spi-max-frequency = <12000000>;
|
|
+ status = "okay";
|
|
+ };
|
|
+ };
|
|
+ };
|
|
+
|
|
+ fragment@1 {
|
|
+ target = <&gpio>;
|
|
+ __overlay__ {
|
|
+ eth1_pins: eth1_pins {
|
|
+ brcm,pins = <23>;
|
|
+ brcm,function = <0>; /* in */
|
|
+ brcm,pull = <0>; /* none */
|
|
+ };
|
|
+ };
|
|
+ };
|
|
+
|
|
+ __overrides__ {
|
|
+ int_pin = <ð1>, "interrupts:0",
|
|
+ <ð1_pins>, "brcm,pins:0";
|
|
+ speed = <ð1>, "spi-max-frequency:0";
|
|
+ };
|
|
+};
|
|
--- a/arch/arm/configs/bcm2709_defconfig
|
|
+++ b/arch/arm/configs/bcm2709_defconfig
|
|
@@ -446,6 +446,7 @@ CONFIG_NETCONSOLE=m
|
|
CONFIG_TUN=m
|
|
CONFIG_VETH=m
|
|
CONFIG_ENC28J60=m
|
|
+CONFIG_QCA7000=m
|
|
CONFIG_MDIO_BITBANG=m
|
|
CONFIG_PPP=m
|
|
CONFIG_PPP_BSDCOMP=m
|
|
--- a/arch/arm/configs/bcmrpi_defconfig
|
|
+++ b/arch/arm/configs/bcmrpi_defconfig
|
|
@@ -439,6 +439,7 @@ CONFIG_NETCONSOLE=m
|
|
CONFIG_TUN=m
|
|
CONFIG_VETH=m
|
|
CONFIG_ENC28J60=m
|
|
+CONFIG_QCA7000=m
|
|
CONFIG_MDIO_BITBANG=m
|
|
CONFIG_PPP=m
|
|
CONFIG_PPP_BSDCOMP=m
|