mirror of https://github.com/hak5/openwrt.git
91 lines
3.7 KiB
Diff
91 lines
3.7 KiB
Diff
Index: linux-2.6.23.17/drivers/ssb/driver_chipcommon.c
|
|
===================================================================
|
|
--- linux-2.6.23.17.orig/drivers/ssb/driver_chipcommon.c
|
|
+++ linux-2.6.23.17/drivers/ssb/driver_chipcommon.c
|
|
@@ -403,6 +403,7 @@ int ssb_chipco_serial_init(struct ssb_ch
|
|
unsigned int irq;
|
|
u32 baud_base, div;
|
|
u32 i, n;
|
|
+ unsigned int ccrev = cc->dev->id.revision;
|
|
|
|
plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
|
|
irq = ssb_mips_irq(cc->dev);
|
|
@@ -414,14 +415,39 @@ int ssb_chipco_serial_init(struct ssb_ch
|
|
chipco_read32(cc, SSB_CHIPCO_CLOCK_M2));
|
|
div = 1;
|
|
} else {
|
|
- if (cc->dev->id.revision >= 11) {
|
|
+ if (ccrev == 20) {
|
|
+ /* BCM5354 uses constant 25MHz clock */
|
|
+ baud_base = 25000000;
|
|
+ div = 48;
|
|
+ /* Set the override bit so we don't divide it */
|
|
+ chipco_write32(cc, SSB_CHIPCO_CORECTL,
|
|
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
|
|
+ | SSB_CHIPCO_CORECTL_UARTCLK0);
|
|
+ } else if ((ccrev >= 11) && (ccrev != 15)) {
|
|
/* Fixed ALP clock */
|
|
baud_base = 20000000;
|
|
+ if (cc->capabilities & SSB_CHIPCO_CAP_PMU) {
|
|
+ /* FIXME: baud_base is different for devices with a PMU */
|
|
+ SSB_WARN_ON(1);
|
|
+ }
|
|
div = 1;
|
|
+ if (ccrev >= 21) {
|
|
+ /* Turn off UART clock before switching clocksource. */
|
|
+ chipco_write32(cc, SSB_CHIPCO_CORECTL,
|
|
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
|
|
+ & ~SSB_CHIPCO_CORECTL_UARTCLKEN);
|
|
+ }
|
|
/* Set the override bit so we don't divide it */
|
|
chipco_write32(cc, SSB_CHIPCO_CORECTL,
|
|
- SSB_CHIPCO_CORECTL_UARTCLK0);
|
|
- } else if (cc->dev->id.revision >= 3) {
|
|
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
|
|
+ | SSB_CHIPCO_CORECTL_UARTCLK0);
|
|
+ if (ccrev >= 21) {
|
|
+ /* Re-enable the UART clock. */
|
|
+ chipco_write32(cc, SSB_CHIPCO_CORECTL,
|
|
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
|
|
+ | SSB_CHIPCO_CORECTL_UARTCLKEN);
|
|
+ }
|
|
+ } else if (ccrev >= 3) {
|
|
/* Internal backplane clock */
|
|
baud_base = ssb_clockspeed(bus);
|
|
div = chipco_read32(cc, SSB_CHIPCO_CLKDIV)
|
|
@@ -433,7 +459,7 @@ int ssb_chipco_serial_init(struct ssb_ch
|
|
}
|
|
|
|
/* Clock source depends on strapping if UartClkOverride is unset */
|
|
- if ((cc->dev->id.revision > 0) &&
|
|
+ if ((ccrev > 0) &&
|
|
!(chipco_read32(cc, SSB_CHIPCO_CORECTL) & SSB_CHIPCO_CORECTL_UARTCLK0)) {
|
|
if ((cc->capabilities & SSB_CHIPCO_CAP_UARTCLK) ==
|
|
SSB_CHIPCO_CAP_UARTCLK_INT) {
|
|
@@ -455,7 +481,7 @@ int ssb_chipco_serial_init(struct ssb_ch
|
|
cc_mmio = cc->dev->bus->mmio + (cc->dev->core_index * SSB_CORE_SIZE);
|
|
uart_regs = cc_mmio + SSB_CHIPCO_UART0_DATA;
|
|
/* Offset changed at after rev 0 */
|
|
- if (cc->dev->id.revision == 0)
|
|
+ if (ccrev == 0)
|
|
uart_regs += (i * 8);
|
|
else
|
|
uart_regs += (i * 256);
|
|
Index: linux-2.6.23.17/include/linux/ssb/ssb_driver_chipcommon.h
|
|
===================================================================
|
|
--- linux-2.6.23.17.orig/include/linux/ssb/ssb_driver_chipcommon.h
|
|
+++ linux-2.6.23.17/include/linux/ssb/ssb_driver_chipcommon.h
|
|
@@ -51,9 +51,12 @@
|
|
#define SSB_CHIPCO_CAP_JTAGM 0x00400000 /* JTAG master present */
|
|
#define SSB_CHIPCO_CAP_BROM 0x00800000 /* Internal boot ROM active */
|
|
#define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */
|
|
+#define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */
|
|
+#define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */
|
|
#define SSB_CHIPCO_CORECTL 0x0008
|
|
#define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */
|
|
#define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
|
|
+#define SSB_CHIPCO_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */
|
|
#define SSB_CHIPCO_BIST 0x000C
|
|
#define SSB_CHIPCO_OTPS 0x0010 /* OTP status */
|
|
#define SSB_CHIPCO_OTPS_PROGFAIL 0x80000000
|