mirror of https://github.com/hak5/openwrt.git
146 lines
3.7 KiB
C
146 lines
3.7 KiB
C
/*
|
|
* HND SiliconBackplane Gigabit Ethernet core software interface
|
|
*
|
|
* Copyright 2007, Broadcom Corporation
|
|
* All Rights Reserved.
|
|
*
|
|
* THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
|
|
* KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
|
|
* SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
|
|
* FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
|
|
*
|
|
*/
|
|
|
|
#include <typedefs.h>
|
|
#include <osl.h>
|
|
#include <pcicfg.h>
|
|
#include <sbconfig.h>
|
|
#include <sbutils.h>
|
|
#include "sbgige.h"
|
|
#include <hndpci.h>
|
|
#include "hndgige.h"
|
|
|
|
uint32
|
|
sb_base(uint32 admatch)
|
|
{
|
|
uint32 base;
|
|
uint type;
|
|
|
|
type = admatch & SBAM_TYPE_MASK;
|
|
ASSERT(type < 3);
|
|
|
|
base = 0;
|
|
|
|
if (type == 0) {
|
|
base = admatch & SBAM_BASE0_MASK;
|
|
} else if (type == 1) {
|
|
ASSERT(!(admatch & SBAM_ADNEG)); /* neg not supported */
|
|
base = admatch & SBAM_BASE1_MASK;
|
|
} else if (type == 2) {
|
|
ASSERT(!(admatch & SBAM_ADNEG)); /* neg not supported */
|
|
base = admatch & SBAM_BASE2_MASK;
|
|
}
|
|
|
|
return (base);
|
|
}
|
|
|
|
/*
|
|
* Setup the gige core.
|
|
* Resetting the core will lose all settings.
|
|
*/
|
|
void
|
|
sb_gige_init(sb_t *sbh, uint32 unit, bool *rgmii)
|
|
{
|
|
volatile pci_config_regs *pci;
|
|
sbgige_pcishim_t *ocp;
|
|
sbconfig_t *sb;
|
|
osl_t *osh;
|
|
uint32 statelow;
|
|
uint32 statehigh;
|
|
uint32 base;
|
|
uint32 idx;
|
|
void *regs;
|
|
|
|
/* Sanity checks */
|
|
ASSERT(sbh);
|
|
ASSERT(rgmii);
|
|
|
|
idx = sb_coreidx(sbh);
|
|
|
|
/* point to the gige core registers */
|
|
regs = sb_setcore(sbh, SB_GIGETH, unit);
|
|
ASSERT(regs);
|
|
|
|
osh = sb_osh(sbh);
|
|
|
|
pci = &((sbgige_t *)regs)->pcicfg;
|
|
ocp = &((sbgige_t *)regs)->pcishim;
|
|
sb = &((sbgige_t *)regs)->sbconfig;
|
|
|
|
/* Enable the core clock and memory access */
|
|
if (!sb_iscoreup(sbh))
|
|
sb_core_reset(sbh, 0, 0);
|
|
|
|
/*
|
|
* Setup the 64K memory-mapped region base address through BAR0.
|
|
* Leave the other BAR values alone.
|
|
*/
|
|
base = sb_base(R_REG(osh, &sb->sbadmatch1));
|
|
W_REG(osh, &pci->base[0], base);
|
|
W_REG(osh, &pci->base[1], 0);
|
|
|
|
/*
|
|
* Enable the PCI memory access anyway. Any PCI config commands
|
|
* issued before the core is enabled will go to the emulation
|
|
* only and will not go to the real PCI config registers.
|
|
*/
|
|
OR_REG(osh, &pci->command, 2);
|
|
|
|
/*
|
|
* Enable the posted write flush scheme as follows:
|
|
*
|
|
* - Enable flush on any core register read
|
|
* - Enable timeout on the flush
|
|
* - Disable the interrupt mask when flushing
|
|
*
|
|
* This differs from the default setting only in that interrupts are
|
|
* not masked. Since posted writes are not flushed on interrupt, the
|
|
* driver must explicitly request a flush in its interrupt handling
|
|
* by reading a core register.
|
|
*/
|
|
W_REG(osh, &ocp->FlushStatusControl, 0x68);
|
|
|
|
/*
|
|
* Determine whether the GbE is in GMII or RGMII mode. This is
|
|
* indicated in bit 16 of the SBTMStateHigh register, which is
|
|
* part of the core-specific flags field.
|
|
*
|
|
* For GMII, bypass the Rx/Tx DLLs, i.e. add no delay to RXC/GTXC
|
|
* within the core. For RGMII, do not bypass the DLLs, resulting
|
|
* in added delay for RXC/GTXC. The SBTMStateLow register contains
|
|
* the controls for doing this in the core-specific flags field:
|
|
*
|
|
* bit 24 - Enable DLL controls
|
|
* bit 20 - Bypass Rx DLL
|
|
* bit 19 - Bypass Tx DLL
|
|
*/
|
|
statelow = R_REG(osh, &sb->sbtmstatelow); /* DLL controls */
|
|
statehigh = R_REG(osh, &sb->sbtmstatehigh); /* GMII/RGMII mode */
|
|
if ((statehigh & (1 << 16)) != 0) /* RGMII */
|
|
{
|
|
statelow &= ~(1 << 20); /* no Rx bypass (delay) */
|
|
statelow &= ~(1 << 19); /* no Tx bypass (delay) */
|
|
*rgmii = TRUE;
|
|
}
|
|
else /* GMII */
|
|
{
|
|
statelow |= (1 << 20); /* Rx bypass (no delay) */
|
|
statelow |= (1 << 19); /* Tx bypass (no delay) */
|
|
*rgmii = FALSE;
|
|
}
|
|
statelow |= (1 << 24); /* enable DLL controls */
|
|
W_REG(osh, &sb->sbtmstatelow, statelow);
|
|
|
|
sb_setcoreidx(sbh, idx);
|
|
}
|