mirror of https://github.com/hak5/openwrt.git
197 lines
4.6 KiB
C
197 lines
4.6 KiB
C
#include <linux/init.h>
|
|
#include <linux/mtd/nand.h>
|
|
#include <linux/mtd/mtd.h>
|
|
#include <linux/mtd/partitions.h>
|
|
#include <linux/delay.h>
|
|
#include <asm/io.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/bootinfo.h>
|
|
#ifdef CONFIG_MIPS_ADM5120
|
|
#include <asm/mach-adm5120/adm5120_defs.h>
|
|
#endif
|
|
|
|
#define IDT434_REG_BASE ((volatile void *) KSEG1ADDR(0x18000000))
|
|
|
|
#define GPIOF 0x050000
|
|
#define GPIOC 0x050004
|
|
#define GPIOD 0x050008
|
|
|
|
#define GPIO_RDY (1 << 0x08)
|
|
#define GPIO_WPX (1 << 0x09)
|
|
#define GPIO_ALE (1 << 0x0a)
|
|
#define GPIO_CLE (1 << 0x0b)
|
|
|
|
#define DEV2BASE 0x010020
|
|
|
|
#define LO_WPX (1 << 0)
|
|
#define LO_ALE (1 << 1)
|
|
#define LO_CLE (1 << 2)
|
|
#define LO_CEX (1 << 3)
|
|
#define LO_FOFF (1 << 5)
|
|
#define LO_SPICS (1 << 6)
|
|
#define LO_ULED (1 << 7)
|
|
|
|
#define MEM32(x) *((volatile unsigned *) (x))
|
|
|
|
|
|
/* RouterBoard RB1xx specific definitions */
|
|
#define SMEM1(x) (*((volatile unsigned char *) (KSEG1ADDR(ADM5120_SRAM1_BASE) + x)))
|
|
|
|
#define NAND_RW_REG 0x0 //data register
|
|
#define NAND_SET_CEn 0x1 //CE# low
|
|
#define NAND_CLR_CEn 0x2 //CE# high
|
|
#define NAND_CLR_CLE 0x3 //CLE low
|
|
#define NAND_SET_CLE 0x4 //CLE high
|
|
#define NAND_CLR_ALE 0x5 //ALE low
|
|
#define NAND_SET_ALE 0x6 //ALE high
|
|
#define NAND_SET_SPn 0x7 //SP# low (use spare area)
|
|
#define NAND_CLR_SPn 0x8 //SP# high (do not use spare area)
|
|
#define NAND_SET_WPn 0x9 //WP# low
|
|
#define NAND_CLR_WPn 0xA //WP# high
|
|
#define NAND_STS_REG 0xB //Status register
|
|
|
|
static void __iomem *p_nand;
|
|
|
|
#ifdef CONFIG_MIKROTIK_RB500
|
|
extern void changeLatchU5(unsigned char orMask, unsigned char nandMask);
|
|
|
|
static int rb500_dev_ready(struct mtd_info *mtd)
|
|
{
|
|
return MEM32(IDT434_REG_BASE + GPIOD) & GPIO_RDY;
|
|
}
|
|
|
|
/*
|
|
* hardware specific access to control-lines
|
|
*
|
|
* ctrl:
|
|
* NAND_CLE: bit 2 -> bit 3
|
|
* NAND_ALE: bit 3 -> bit 2
|
|
*/
|
|
static void rbmips_hwcontrol500(struct mtd_info *mtd, int cmd,
|
|
unsigned int ctrl)
|
|
{
|
|
struct nand_chip *chip = mtd->priv;
|
|
unsigned char orbits, nandbits;
|
|
|
|
if (ctrl & NAND_CTRL_CHANGE) {
|
|
|
|
orbits = (ctrl & NAND_CLE) << 1;
|
|
orbits |= (ctrl & NAND_ALE) >> 1;
|
|
|
|
nandbits = (~ctrl & NAND_CLE) << 1;
|
|
nandbits |= (~ctrl & NAND_ALE) >> 1;
|
|
|
|
changeLatchU5(orbits, nandbits);
|
|
}
|
|
if (cmd != NAND_CMD_NONE)
|
|
writeb(cmd, chip->IO_ADDR_W);
|
|
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_MIPS_ADM5120
|
|
static int rb100_dev_ready(struct mtd_info *mtd)
|
|
{
|
|
return SMEM1(NAND_STS_REG) & 0x80; /* found out by experiment */
|
|
}
|
|
|
|
static void rbmips_hwcontrol100(struct mtd_info *mtd, int cmd, unsigned int ctrl)
|
|
{
|
|
struct nand_chip *chip = mtd->priv;
|
|
|
|
if (ctrl & NAND_CTRL_CHANGE)
|
|
SMEM1(ctrl) = 0x01;
|
|
if (cmd != NAND_CMD_NONE)
|
|
writeb(cmd, chip->IO_ADDR_W);
|
|
}
|
|
#endif
|
|
|
|
|
|
static struct mtd_partition partition_info[] = {
|
|
{
|
|
name:"RouterBoard NAND Boot",
|
|
offset:0,
|
|
size:4 * 1024 * 1024},
|
|
{
|
|
name:"RouterBoard NAND Main",
|
|
offset:MTDPART_OFS_NXTBLK,
|
|
size:MTDPART_SIZ_FULL}
|
|
};
|
|
|
|
static struct mtd_info rmtd;
|
|
static struct nand_chip rnand;
|
|
|
|
static unsigned init_ok = 0;
|
|
|
|
unsigned get_rbnand_block_size(void)
|
|
{
|
|
if (init_ok)
|
|
return rmtd.writesize;
|
|
else
|
|
return 0;
|
|
}
|
|
|
|
EXPORT_SYMBOL(get_rbnand_block_size);
|
|
|
|
int __init rbmips_init(void)
|
|
{
|
|
memset(&rmtd, 0, sizeof(rmtd));
|
|
memset(&rnand, 0, sizeof(rnand));
|
|
|
|
#ifdef CONFIG_MIKROTIK_RB500
|
|
printk("RB500 nand\n");
|
|
changeLatchU5(LO_WPX | LO_FOFF | LO_CEX,
|
|
LO_ULED | LO_ALE | LO_CLE);
|
|
rnand.cmd_ctrl = rbmips_hwcontrol500;
|
|
|
|
rnand.dev_ready = rb500_dev_ready;
|
|
rnand.IO_ADDR_W = (unsigned char *)
|
|
KSEG1ADDR(MEM32(IDT434_REG_BASE + DEV2BASE));
|
|
rnand.IO_ADDR_R = rnand.IO_ADDR_W;
|
|
#endif
|
|
|
|
#ifdef CONFIG_MIPS_ADM5120
|
|
printk("RB100 nand\n");
|
|
/* enable NAND flash */
|
|
MEM32(0xB2000064) = 0x100;
|
|
/* boot done */
|
|
MEM32(0xB2000008) = 0x1;
|
|
SMEM1(NAND_SET_SPn) = 0x01;
|
|
SMEM1(NAND_CLR_WPn) = 0x01;
|
|
rnand.IO_ADDR_R = (unsigned char *)KSEG1ADDR(ADM5120_SRAM1_BASE);
|
|
rnand.IO_ADDR_W = rnand.IO_ADDR_R;
|
|
rnand.cmd_ctrl = rbmips_hwcontrol100;
|
|
rnand.dev_ready = rb100_dev_ready;
|
|
#endif
|
|
p_nand = (void __iomem *) ioremap((void *) 0x18a20000, 0x1000);
|
|
if (!p_nand) {
|
|
printk("RBnand Unable ioremap buffer");
|
|
return -ENXIO;
|
|
}
|
|
rnand.ecc.mode = NAND_ECC_SOFT;
|
|
rnand.chip_delay = 25;
|
|
rnand.options |= NAND_NO_AUTOINCR;
|
|
rmtd.priv = &rnand;
|
|
|
|
#ifdef CONFIG_MIKROTIK_RB500
|
|
int *b;
|
|
|
|
b = (int *) KSEG1ADDR(0x18010020);
|
|
printk("dev2base 0x%08x mask 0x%08x c 0x%08x tc 0x%08x\n", b[0],
|
|
b[1], b[2], b[3]);
|
|
#endif
|
|
|
|
if (nand_scan(&rmtd, 1) && nand_scan(&rmtd, 1)
|
|
&& nand_scan(&rmtd, 1) && nand_scan(&rmtd, 1)) {
|
|
printk("RBxxx nand device not found");
|
|
iounmap((void *) p_nand);
|
|
return -ENXIO;
|
|
}
|
|
|
|
add_mtd_partitions(&rmtd, partition_info, 2);
|
|
init_ok = 1;
|
|
return 0;
|
|
}
|
|
|
|
module_init(rbmips_init);
|